| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 7 | CENTER NO. 4 ENGINE UNDER COVER | 51447D | - | - | - |
| 8 | CENTER NO. 1 FLOOR BRACE | 57543C | - | - | - |
| 9 | NO. 2 AIR FUEL RATIO SENSOR | 89467C | - | - | - |
| 10 | FRONT EXHAUST PIPE ASSEMBLY | 17410 | ( )
|
- | - |
| ● | Non-reusable part | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 11 | FRONT FLOOR COVER LH | 58166A | - | - | - |
| 12 | FRONT FLOOR COVER RH | 58165C | - | - | - |
| 13 | FRONT NO. 1 FLOOR HEAT INSULATOR | 58151 | - | - | - |
| 14 | FRONT NO. 2 FLOOR HEAT INSULATOR | 58153 | - | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 15 | REAR CONSOLE BOX ASSEMBLY | 58910C | - | - | - |
| 16 | TRANSMISSION CONTROL CABLE ASSEMBLY | 33820B | ( )
|
- | - |
| ● | Non-reusable part | - | - |
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during transmission control cable assembly removal/installation are shown below.
When the cable is disconnected / reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
2.SECURE VEHICLE
Fully apply the parking brake and chock a wheel.
Make sure to apply the parking brake and chock a wheel before performing this procedure.
If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.
28800
3.REMOVE AUXILIARY BATTERY
4.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
w/ Stop and Start System:
Click hereEngine / Hybrid System>M15A-FKS (STARTING)>STARTER (w/ Stop And Start System)>REMOVAL
w/o Stop and Start System:
Click hereEngine / Hybrid System>M15A-FKS (STARTING)>STARTER (w/o Stop And Start System)>REMOVAL
74404A
6.REMOVE BATTERY CLAMP SUB-ASSEMBLY
51447D
7.REMOVE CENTER NO. 4 ENGINE UNDER COVER
57543C
8.REMOVE CENTER NO. 1 FLOOR BRACE
89467C
9.DISCONNECT NO. 2 AIR FUEL RATIO SENSOR
58166A
11.REMOVE FRONT FLOOR COVER LH
58165C
12.REMOVE FRONT FLOOR COVER RH
Use the same procedure as for the LH side.
58151
13.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR
58153
14.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR
58910C
15.REMOVE REAR CONSOLE BOX ASSEMBLY
33820B
16.REMOVE TRANSMISSION CONTROL CABLE ASSEMBLY
|
Remove in this Direction | - | - |
Remove the clip and disconnect the transmission control select cable from the floor shift shift lever assembly.
Disconnect the transmission control shift cable from the floor shift shift lever assembly.
Disengage the 2 claws and disconnect the transmission control cable assembly from the floor shift shift lever assembly as shown in the illustration.
Do not forcibly pull the transmission control cable assembly into the cabin.
Remove the 2 clips (A) to disconnect the transmission control cable assembly from the manual transaxle assembly.
Remove the 2 clips (B) to disconnect the transmission control cable assembly from the control cable bracket assembly.
Remove the nut.
Disengage the guide and disconnect the transmission control cable assembly from the vehicle body.
Remove the 2 nuts and transmission control cable assembly from the vehicle body.