| *A | for AWD | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 8 | HYBRID INVERTER PROTECTOR ASSEMBLY | G92D0 | ( )
|
- | - |
| 9 | REAR DECK FLOOR BOX | 64993 | - | - | - |
| 10 | DECK BOARD ASSEMBLY | 58410B | - | - | - |
| *A | for AWD | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| *A | for 2WD | *B | w/ Cover |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 17 | REAR SEAT CUSHION LEG SUB-ASSEMBLY | 71403 | - | - | - |
| 18 | REAR UNDER COVER | 76971G | - | - | - |
| 19 | REAR DOOR SCUFF PLATE INSIDE LH | 67918F | - | - | - |
| 20 | EAR SEAT CUSHION LOCK HOOK | 72693 | - | - | - |
| 21 | BENCH TYPE REAR SEAT CUSHION ASSEMBLY | - | - | - | - |
| 22 | REAR CENTER SEAT OUTER BELT ASSEMBLY | 73350C | - | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 23 | HV FLOOR UNDER WIRE | 821H1 | ( )
|
- | - |
| 24 | ENGINE WIRE | 82121 | ( )
|
- | - |
| 25 | SERVICE PLUG GRIP | G3834 | - | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
821H3
2.INSTALL HV BATTERY PACK WIRE (for AWD)
|
|
| *a | Interlock | *b | Waterproof Seal |
Temporarily install the HV battery pack wire with the 4 bolts..
Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.
Do not allow any foreign matter or water to enter the rear hybrid motor control inverter assembly.
Insulate the disconnected terminals with insulating tape.
To prevent damage due to staticelectricity, do not touch the terminals of the disconnected connectors.
Using an insulated tool, install 2 bolts (A).
Using an insulated tool, install 2 bolts (B).
| *a | Shield Ground | - | - |
Connect the shield ground to the HV battery.
Connect the 2 HV battery junction block assembly and floor wire connectors.
821H1
3.INSTALL FLOOR UNDER WIRE (for AWD)
|
|
| *a | Waterproof Seal | - | - |
Temporarily install the HV floor under wire with the 4 bolts.
Cover the hole where the cable was connected with tape (non-residue type) or equivalent to prevent entry of foreign matter.
Do not allow any foreign matter or water to enter the inverter with converter assembly.
Insulate the disconnected terminals with insulating tape.
To prevent damage due to staticelectricity, do not touch the terminalsof the disconnected connectors.
Using an insulated tool, fully tighten 2 bolts (A).
Using an insulated tool, fully tighten 2 bolts (B).
Connect the 3 connectors.
Connect the 4 clamps.
Connect the HV floor under wire connector.
Install the bolt and nut.
Install the 3 nuts and clamp.
Install the HV floor under wire with the 2 nuts
64740C
5.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH (for AWD)
58387B
6.INSTALL REAR FLOOR FINISH PLATE (for AWD)
7.INSTALL REAR SEATBACK ASSEMBLY LH (for AWD)
64993
9.INSTALL REAR DECK FLOOR BOX (for AWD)
58410B
10.INSTALL DECK BOARD ASSEMBLY (for AWD)
821H1
11.INSTALL FLOOR UNDER WIRE (for 2WD)
|
|
51201
12.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
64740C
13.INSTALL FRONT FLOOR COVER LH (w/ Cover)
57628E
14.INSTALL REAR FLOOR SIDE MEMBER COVER LH
71403
17.INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY
76971G
18.INSTALL REAR UNDER COVER
67918F
19.INSTALL REAR DOOR SCUFF PLATE INSIDE LH
72693
20.INSTALL REAR SEAT CUSHION LOCK HOOK
for 60/40 Split Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type)>INSTALLATION
for 40/20/40 Split Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 40/20/40 Split Seat Type)>INSTALLATION
21.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY
for 60/40 Split Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type)>INSTALLATION
for 40/20/40 Split Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 40/20/40 Split Seat Type)>INSTALLATION
73350C
22.CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
for 60/40 Split Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 60/40 Split Seat Type)>INSTALLATION
for 40/20/40 Split Seat Type:
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for 40/20/40 Split Seat Type)>INSTALLATION
G3834
25.INSTALL SERVICE PLUG GRIP