|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
| ● | Non-reusable part |
|
Lithium soap base glycol grease |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 13 | NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY | - | ( )
|
- | - |
| 14 | COLUMN HOLE COVER SILENCER SHEET | - | - | - | - |
| 15 | NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY | - | - | - | - |
|
Tightening torque for "Major areas involving basic vehicle performance such as moving/turning/stopping" : N*m (kgf*cm, ft.*lbf) | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 16 | DASH PANEL HEAT INSULATOR | 55225C | ( )
|
- | - |
| 17 | NO. 1 ENGINE UNDER COVER ASSEMBLY | 51410 | - | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
44785
1.INSTALL BRAKE BOOSTER GASKET
44610
2.TEMPORARILY INSTALL BRAKE BOOSTER ASSEMBLY
|
|
Temporarily install the brake booster assembly to the vehicle.
Return the front No. 1 brake tube and front No. 2 brake tube to their original positions.
3.TEMPORARILY INSTALL CLEVIS LOCK NUT
|
|
4.TEMPORARILY INSTALL BRAKE MASTER CYLINDER PUSH ROD CLEVIS
|
|
44610
5.INSTALL BRAKE BOOSTER ASSEMBLY
| *A | w/o Stop And Start System | *B | w/ Stop And Start System |
|
Protective Tape | - | - |
Install the 4 nuts to secure the brake booster assembly.
Tighten the 4 nuts in the order shown in the illustration.
Remove the protective tape.
Connect the vacuum warning switch connector.
Connect the vacuum sensor connector.
6.CONNECT BRAKE LINE
| *a | Torque Wrench Fulcrum Length | - | - |
Using a union nut wrench, connect the 2 brake lines to the brake actuator assembly.
Do not kink or damage the brake lines.
Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
17.4 N*m (177 kgf*cm, 13 ft.*lbf)
47374B
7.INSTALL NO. 4 BRAKE TUBE CLAMP
47373B
8.INSTALL NO. 3 BRAKE TUBE CLAMP
82111
9.INSTALL ENGINE ROOM MAIN WIRE
44773F
10.CONNECT UNION TO CHECK VALVE HOSE
| *a | Paint Mark | - | - |
Connect the union to check valve hose to the brake booster assembly and slide the clip to secure it.
When connecting the union to check valve hose, face the paint mark up.
Make sure that the tabs of the clip are facing upward.
45259A
14.INSTALL COLUMN HOLE COVER SILENCER SHEET
55606
15.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
55225C
16.INSTALL DASH PANEL HEAT INSULATOR
Temporarily install the dash panel heat insulator to the vehicle body with the 2 nuts.
Install the nut.
Tighten the 2 nuts.
51410
17.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
74404A
18.INSTALL BATTERY CLAMP SUB-ASSEMBLY
17701
19.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
17801
20.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
47201
23.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY
24.INSPECT AND ADJUST BRAKE PEDAL