Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › from 2021.07
RM3700E _57 Power Source / Network _093026 NETWORKING _0445205 CAN COMMUNICATION SYSTEM(for Gasoline Model) U

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  TERMINALS OF ECU  


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

This section describes the standard values for all CAN related components.



HINT:
·

The systems (ECUs and sensors) that use CAN communication vary depending on the vehicle and optional equipment. Check which systems (ECUs and sensors) are installed to the vehicle.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



NO. 1 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 1 global CAN junction connector.

i.

Connection diagram

C422304C08
1.521,0.74 2.021,0.99 0.5,0.25 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.604,0.792 2.021,0.99 0.417,0.198 10 false H110
*a Front view of wire harness connector
(to No. 1 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 1 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H110-1 (CANH) LG Power steering ECU assembly
(for Bus 4)
H110-12 (CANL) W
H110-2 (CANH) SB Steering sensor
(for Bus 4)
H110-13 (CANL) W
H110-4 (CANH) BR No. 2 global CAN junction connector
(for Bus 4)
H110-15 (CANL) W




NO. 2 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 2 global CAN junction connector.

i.

Connection diagram

C422305C02
1.531,0.802 2.031,1.052 0.5,0.25 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 1.604,0.854 2.042,1.115 0.438,0.26 10 false H112
*a Front view of wire harness connector
(to No. 2 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 2 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H112-1 (CANH) B Airbag sensor assembly
(for Bus 4)
H112-7 (CANL) W
H112-2 (CANH) V Central gateway ECU (network gateway ECU)
(for Bus 4)
H112-8 (CANL) W
H112-3 (CANH) G Brake actuator assembly
(for Bus 4)
H112-9 (CANL) W
H112-4 (CANH) BR No. 1 global CAN junction connector
(for Bus 4)
H112-10 (CANL) W




NO. 4 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 4 global CAN junction connector.

i.

Connection diagram

C422304C11
1.521,0.74 2.021,0.99 0.5,0.25 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.615,0.792 2.031,0.99 0.417,0.198 10 false H115
*a Front view of wire harness connector
(to No. 4 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 4 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H115-1 (CANH) R Central gateway ECU (network gateway ECU)
(for Bus 3)
H115-12 (CANL) W
H115-2 (CANH) BR Combination meter assembly
(for Bus 3)
H115-13 (CANL) W
H115-3 (CANH) LG Radio and display receiver assembly*1
(for Bus 3)
H115-14 (CANL) W
H115-4 (CANH) BE Telematics transceiver*2
(for Bus 3)
H115-15 (CANL) W
H115-5 (CANH) SB Meter mirror sub-assembly*3
(for Bus 3)
H115-16 (CANL) W

*1: for Radio and Display Type without TAS Type

*2: w/ Telematics Transceiver

*3: w/ Headup Display





NO. 6 GLOBAL CAN JUNCTION CONNECTOR (for TMC Made)


a.

Check the No. 6 global CAN junction connector.

i.

Connection diagram

C422304C14
1.521,0.74 2.021,0.99 0.5,0.25 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.604,0.792 2.021,0.99 0.417,0.198 10 false H117
*a Front view of wire harness connector
(to No. 6 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 5 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H117-1 (CANH) Y ECM
(for Bus 2)
H117-12 (CANL) W
H117-3 (CANH) LG Central gateway ECU (network gateway ECU)
(for Bus 2)
H117-14 (CANL) W
H117-4 (CANH) L TCM
(for Bus 2)
H117-15 (CANL) W




NO. 6 GLOBAL CAN JUNCTION CONNECTOR (for TMMF Made)


a.

Check the No. 6 global CAN junction connector.

i.

Connection diagram

C422304C38
1.521,0.74 2.021,0.99 0.5,0.25 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.604,0.792 2.021,0.99 0.417,0.198 10 false H117
*a Front view of wire harness connector
(to No. 6 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 5 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H117-1 (CANH) Y ECM
(for Bus 2)
H117-12 (CANL) W
H117-2 (CANH) BR Engine stop and start ECU*1
(for Bus 2)
H117-13 (CANL) W
H117-3 (CANH) LG Central gateway ECU (network gateway ECU)
(for Bus 2)
H117-14 (CANL) W
H117-4 (CANH) L TCM*2
(for Bus 2)
H117-15 (CANL) W
H117-9 (CANH) B Brake actuator assembly
(for Chassis Local Bus)
H117-20 (CANL) W
H117-10 (CANH) R Engine stop and start ECU*1
(for Chassis Local Bus)
H117-21 (CANL) W
H117-11 (CANH) V Central gateway ECU (network gateway ECU)
(for Chassis Local Bus)
H117-22 (CANL) W

*1: w/ Stop and Start System

*2: for CVT





NO. 7 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 7 global CAN junction connector.

i.

Connection diagram

C440226C06
1.521,0.74 2.021,0.99 0.5,0.25 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.604,0.781 2.021,0.979 0.417,0.198 10 false H143
*a Front view of wire harness connector
(to No. 7 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 7 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H143-1 (CANH) R Forward recognition camera*1
(for Bus 1)
H143-5 (CANL) W
H143-2 (CANH) SB Central gateway ECU (network gateway ECU)
(for Bus 1)
H143-6 (CANL) W
H143-3 (CANH) L Millimeter wave radar sensor assembly*1
(for Bus 1)
H143-7 (CANL) W
H143-4 (CANH) V No. 8 global CAN junction connector
(for Bus 1)
H143-8 (CANL) W

*1: w/ Toyota Safety Sense





NO. 8 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 8 global CAN junction connector.

i.

Connection diagram

C422305C09
1.531,0.802 2.031,1.052 0.5,0.25 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 1.604,0.844 2.042,1.104 0.438,0.26 10 false O113
*a Front view of wire harness connector
(to No. 8 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 8 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
O113-1 (CANH) BE Clearance warning ECU assembly*1
(for Bus 1)
O113-7 (CANL) W
O113-2 (CANH) V No. 7 global CAN junction connector
(for Bus 1)
O113-8 (CANL) W
O113-3 (CANH) GR Blind spot monitor sensor LH*2
(for Bus 1)
O113-9 (CANL) W
O113-4 (CANH) LG Rear television camera assembly*3
(for Bus 1)
O113-10 (CANL) W
O113-5 (CANH) R No. 1 CAN junction terminal
(for Bus 1)
O113-11 (CANL) W
O113-6 (CANH) P Parking assist ECU*4
(for Bus 1)
O113-12 (CANL) W

*1: w/ TOYOTA Parking Assist-sensor System

*2: w/ Blind Spot Monitor System

*3: w/ Parking Assist Monitor System

*4: w/ Panoramic View Monitor System





NO. 9 GLOBAL CAN JUNCTION CONNECTOR (for TMMF Made)


a.

Check the No. 9 global CAN junction connector.

i.

Connection diagram

C422306C54
1.51,0.781 2.01,1.031 0.5,0.25 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a 1.625,0.813 2.083,1.24 0.458,0.427 10 false O87
*a Front view of wire harness connector
(to No. 9 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 9 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
O87-1 (CANH) G Central gateway ECU (network gateway ECU)
(for Bus 6)
O87-12 (CANL) W
O87-2 (CANH) L Central gateway ECU (network gateway ECU)
(for Bus 6)
O87-13 (CANL) W
O87-4 (CANH) R Tire pressure warning ECU and receiver
(for Bus 6)
O87-15 (CANL) W




NO. 11 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 11 global CAN junction connector.

i.

Connection diagram

C440226C07
1.531,0.802 2.031,1.052 0.5,0.25 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 1.604,0.854 2.042,1.115 0.438,0.26 10 false H142
*a Front view of wire harness connector
(to No. 11 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 11 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H142-1 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 5)
H142-5 (CANL) W
H142-2 (CANH) P No. 12 global CAN junction connector
(for Bus 5)
H142-6 (CANL) W
H142-3 (CANH) L Certification ECU (smart key ECU assembly)*1
(for Bus 5)
H142-7 (CANL) W
H142-4 (CANH) Y Headlight ECU sub-assembly RH*2
(for Bus 5)
H142-8 (CANH) W

*1: w/ Entry and Start System

*2: w/ Adaptive High Beam System





NO. 12 GLOBAL CAN JUNCTION CONNECTOR


a.

Check the No. 12 global CAN junction connector.

i.

Connection diagram

C422305C10
1.531,0.802 2.031,1.052 0.5,0.25 0.146,0.125 0.458,0.281 0.313,0.156 10 false *a 1.604,0.854 2.042,1.115 0.438,0.26 10 false O114
*a Front view of wire harness connector
(to No. 12 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 12 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
O114-2 (CANH) R Air conditioning amplifier assembly
(for Bus 5)
O114-8 (CANL) W
O114-3 (CANH) V Headlight ECU sub-assembly LH*1
(for Bus 5)
O114-9 (CANL) W
O114-4 (CANH) SB Main body ECU (multiplex network body ECU)
(for Bus 5)
O114-10 (CANL) W
O114-5 (CANH) P No. 11 global CAN junction connector
(for Bus 5)
O114-11 (CANL) W
O114-6 (CANH) V Multiplex network door ECU*2
(for Bus 5)
O114-12 (CANL) W

*1: w/ Adaptive High Beam System

*2: w/ Power Back Door





NO. 13 GLOBAL CAN JUNCTION CONNECTOR (for TMMF Made)


a.

Check the No. 13 global CAN junction connector.

i.

Connection diagram

C422304C39
1.521,0.74 2.021,0.99 0.5,0.25 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.604,0.792 2.021,0.99 0.417,0.198 10 false H156
*a Front view of wire harness connector
(to No. 13 Global CAN Junction Connector)
- -



ii.

Check the connection diagram of the components which are connected to the No. 13 global CAN junction connector.

Terminal No. (Symbol) Wiring Color Connected to
H156-1 (CANH) B Central gateway ECU (network gateway ECU)
(for Bus 7)
H156-12 (CANL) W
H156-2 (CANH) G Option connector (bus buffer ECU)
(for Bus 7)
H156-13 (CANL) W
H156-3 (CANH) L Central gateway ECU (network gateway ECU)
(for Bus 7)
H156-14 (CANL) W
H156-4 (CANH) P Radio and display receiver assembly*1
(for Bus 7)
H156-15 (CANL) W

*1: for Radio and Display Type with TAS Type





NO. 1 CAN JUNCTION TERMINAL


a.

Check the No. 1 CAN junction terminal.

i.
C395263C20
2.75,0.833 3.271,1.083 0.521,0.25 0.104,0.094 0.417,0.25 0.313,0.156 10 false *a 2.865,0.875 3.208,1.042 0.344,0.167 10 false O86
*a Rear view of wire harness connector
(to No. 1 CAN Junction Terminal)


Connection diagram


ii.

Check the connection diagram of the components which are connected to the No. 1 CAN junction terminal.

Terminal No. (Symbol) Wiring Color Connected to
O86-3 (CANH) R No. 8 global CAN junction connector
(for Bus 1)
O86-2 (CANL) W




DLC3


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

C427140C05
1.531,0.76 1.927,1.052 0.396,0.292 0.104,0.115 0.417,0.313 0.313,0.198 10 false *1 1.646,0.813 2.063,1.115 0.417,0.302 10 false H3
*1 DLC3 - -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H3-6 (CANH) - H3-14 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H3-6 (CANH) - H3-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H3-14 (CANL) - H3-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H3-6 (CANH) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H3-14 (CANL) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)


C422307C03
3.49,0.135 3.906,0.385 0.417,0.25 0.188,0.198 0.5,0.396 0.313,0.198 10 false *a 3.594,0.198 4.052,0.396 0.458,0.198 10 false H40
*a Component without harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H40 central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C422308C03
0.625,0.792 1.125,1.042 0.5,0.25 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 0.729,0.854 1.042,1.052 0.313,0.198 10 false H40
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Diagnosis Bus Branch Lines (DLC3 - Central gateway ECU (network gateway ECU))
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H40-16 (CA6H) - H40-17 (CA6L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 1 MΩ or higher
H40-16 (CA6H) - H40-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-17 (CA6L) - H40-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-16 (CA6H) - H40-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-17 (CA6L) - H40-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 1 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H40-28 (CA1H) - H40-27 (CA1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H40-28 (CA1H) - H40-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-27 (CA1L) - H40-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-28 (CA1H) - H40-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-27 (CA1L) - H40-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 2 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H40-26 (CA4H) - H40-25 (CA4L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H40-26 (CA4H) - H40-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-25 (CA4L) - H40-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-26 (CA4H) - H40-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-25 (CA4L) - H40-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 3 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H40-30 (CA3H) - H40-29 (CA3L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H40-30 (CA3H) - H40-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-29 (CA3L) - H40-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-30 (CA3H) - H40-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-29 (CA3L) - H40-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 4 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H40-24 (CA2H) - H40-23 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H40-24 (CA2H) - H40-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-23 (CA2L) - H40-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-24 (CA2H) - H40-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-23 (CA2L) - H40-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 5 Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H40-7 (CA5H) - H40-8 (CA5L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H40-7 (CA5H) - H40-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-8 (CA5L) - H40-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-7 (CA5H) - H40-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-8 (CA5L) - H40-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 6 Main Lines (for TMMF Made)
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H40-31 (CA7H) - H40-10 (CAVH) HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
H40-32 (CA7L) - H40-11 (CAVL) LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
H40-31 (CA7H) - H40-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-32 (CA7L) - H40-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-31 (CA7H) - H40-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-32 (CA7L) - H40-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 7 Main Lines (for TMC Made)
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H40-5 (CA8H) - H40-6 (CA8L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H40-5 (CA8H) - H40-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-6 (CA8L) - H40-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-5 (CA8H) - H40-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-6 (CA8L) - H40-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Bus 7 Main Lines (for TMMF Made)
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H40-5 (CA8H) - H40-14 (CAXH) HIGH-level CAN bus line - HIGH-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
H40-6 (CA8L) - H40-15 (CAXL) LOW-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal Below 1 Ω
H40-5 (CA8H) - H40-22 (GND) HIGH-level CAN bus ine - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-6 (CA8L) - H40-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-5 (CA8H) - H40-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-6 (CA8L) - H40-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher

Chassis Local Bus Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H40-12 (CAWH) - H40-13 (CAWL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H40-12 (CAWH) - H40-22 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-13 (CAWL) - H40-22 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H40-12 (CAWH) - H40-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H40-13 (CAWL) - H40-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




OPTION CONNECTOR (BUS BUFFER ECU)


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H62 option connector (bus buffer ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C446923C02
3.729,0.76 4.135,1.031 0.406,0.271 0.229,0.781 0.635,1.052 0.406,0.271 0.385,0.188 0.698,0.385 0.313,0.198 10 false *a 3.729,0.156 4.042,0.354 0.313,0.198 10 false *1 3.844,0.802 4.156,1 0.313,0.198 10 false H3 0.302,0.823 0.615,1.021 0.313,0.198 10 false H62
*1 DLC3 - -
*a Front view of wire harness connector
(to Option Connector (Bus Buffer ECU))
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H62-2 (CAN+) - H62-1 (CAN-) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H62-2 (CAN+) - H3-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H62-1 (CAN-) - H3-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H62-2 (CAN+) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H62-1 (CAN-) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




ECM


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>TERMINALS OF ECM

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A54 ECM connector.


c.
C392553C15
0.198,0.938 0.615,1.188 0.417,0.25 0.188,0.177 0.406,0.427 0.219,0.25 10 false *a 0.302,0.99 0.729,1.198 0.427,0.208 10 false A54
*a Front view of wire harness connector
(to ECM)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A54-8 (CANH) - A54-18 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A54-8 (CANH) - A54-10 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A54-18 (CANL) - A54-10 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A54-8 (CANH) - A54-1 (BATT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A54-18 (CANL) - A54-1 (BATT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




TCM (for CVT)


Refer to Terminals of ECU.

Click hereDrivetrain>K320 (MULTIDRIVE / CVT)>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the D71 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

C434462C01
0.167,0.75 0.667,1 0.5,0.25 3.75,0.75 4.25,1 0.5,0.25 0.292,0.792 0.75,0.99 0.458,0.198 10 false D71 3.906,0.792 4.365,0.99 0.458,0.198 10 false H3 0.146,0.094 0.604,0.292 0.458,0.198 10 false *a 3.792,0.125 4.104,0.323 0.313,0.198 10 false *1
*1 DLC3 - -
*a Front view of wire harness connector
(to TCM)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
D71-15 (CANH) - D71-16 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
D71-15 (CANH) - D71-2 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D71-16 (CANL) - D71-2 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
D71-15 (CANH) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
D71-16 (CANL) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type without TAS Type)


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C427752C05
3.729,0.76 4.135,1.031 0.406,0.271 0.229,0.781 0.635,1.052 0.406,0.271 0.385,0.188 0.698,0.385 0.313,0.198 10 false *a 3.729,0.156 4.042,0.354 0.313,0.198 10 false *1 3.854,0.813 4.167,1.01 0.313,0.198 10 false H3 0.302,0.823 0.615,1.021 0.313,0.198 10 false H80
*1 DLC3 - -
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H80-13 (CANH) - H80-14 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H80-13 (CANH) - H3-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H80-14 (CANL) - H3-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H80-13 (CANH) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H80-14 (CANL) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




RADIO AND DISPLAY RECEIVER ASSEMBLY (for Radio and Display Type with TAS Type)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type with TAS Type)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H80 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C427752C14
3.729,0.76 4.135,1.031 0.406,0.271 0.229,0.781 0.635,1.052 0.406,0.271 0.385,0.188 0.698,0.385 0.313,0.198 10 false *a 3.729,0.156 4.042,0.354 0.313,0.198 10 false *1 3.844,0.802 4.156,1 0.313,0.198 10 false H3 0.302,0.823 0.615,1.021 0.313,0.198 10 false H80
*1 DLC3 - -
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H80-1 (CA8H) - H80-2 (CA8L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H80-1 (CA8H) - H3-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H80-2 (CA8L) - H3-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H80-1 (CA8H) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H80-2 (CA8L) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BRAKE ACTUATOR ASSEMBLY (for TMC Made)


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMC Made)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A94 brake actuator assembly connector.


c.
C434856C11
1.479,0.115 1.885,0.344 0.406,0.229 0.073,0.094 0.385,0.292 0.313,0.198 10 false *a 1.573,0.156 1.885,0.354 0.313,0.198 10 false A94
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A94-27 (CANH) - A94-43 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A94-27 (CANH) - A94-1(GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A94-43 (CANL) - A94-1 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A94-27 (CANH) - A94-14 (+BS) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A94-43 (CANL) - A94-14 (+BS) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BRAKE ACTUATOR ASSEMBLY (for TMMF Made)


Refer to Terminals of ECU.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A39 brake actuator assembly connector.


c.
C434481C01
1.5,0.25 2,0.5 0.5,0.25 0.125,0.104 0.438,0.26 0.313,0.156 10 false *a 1.625,0.302 1.938,0.458 0.313,0.156 10 false A39
*a Front view of wire harness connector
(to Brake Actuator Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Bus 4 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A39-5 (CANH) - A39-19 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A39-5 (CANH) - A39-46 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A39-19 (CANL) - A39-46 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A39-5 (CANH) - A39-30 (+BS) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A39-19 (CANL) - A39-30 (+BS) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Chassis Local Bus Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A39-11 (CA2H) - A39-25 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
A39-11 (CA2H) - A39-46 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A39-25 (CA2H) - A39-46 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A39-11 (CA2L) - A39-30 (+BS) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A39-25 (CA2L) - A39-30 (+BS) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



STEERING SENSOR


C358931C13
4.74,0.854 5.073,1.104 0.333,0.25 4.667,0.177 4.979,0.375 0.313,0.198 10 false *a 4.792,0.917 5.104,1.115 0.313,0.198 10 false H39
*a Component without harness connected
(Steering Sensor)
- -


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H39 steering sensor connector.


c.
C427527C05
0.552,0.927 0.958,1.229 0.406,0.302 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 0.625,0.99 0.938,1.188 0.313,0.198 10 false H39
*a Front view of wire harness connector
(to Steering Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H39-3 (CANH) - H39-8 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H39-3 (CANH) - H39-6 (ESS) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H39-8 (CANL) - H39-6 (ESS) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H39-3 (CANH) - H39-4 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H39-8 (CANL) - H39-4 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




POWER STEERING ECU ASSEMBLY


Refer to Terminals of ECU.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H1 and H2 power steering ECU assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

C434461C03
1.094,0.792 1.594,1.042 0.5,0.25 3.948,0.792 4.448,1.042 0.5,0.25 0.104,0.115 0.417,0.313 0.313,0.198 10 false *a 1.26,0.833 1.573,1.031 0.313,0.198 10 false H1 4.115,0.833 4.427,1.031 0.313,0.198 10 false H2
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H1-7 (CANH) - H1-8 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H1-7 (CANH) - H2-2 (PGND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H1-8 (CANL) - H2-2 (PGND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H1-7 (CANH) - H2-1 (PIG) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H1-8 (CANL) - H2-1 (PIG) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIRBAG SENSOR ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H14 airbag sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C427534C05
0.792,0.781 1.177,1.042 0.385,0.26 3.594,0.771 3.979,1.031 0.385,0.26 0.385,0.208 0.698,0.406 0.313,0.198 10 false *a 3.406,0.208 3.719,0.406 0.313,0.198 10 false *1 3.698,0.823 4.01,1.021 0.313,0.198 10 false H3 0.865,0.833 1.177,1.031 0.313,0.198 10 false H14
*1 DLC3 - -
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H14-26 (CAFH) - H14-27 (CAFL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H14-26 (CAFH) - H14-33 (E1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H14-27 (CAFL) - H14-33 (E1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H14-26 (CAFH) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H14-27 (CAFL) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)


Refer to Terminals of ECU.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, Gasoline Model)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


c.
C422313C02
1.563,0.125 2.063,0.375 0.5,0.25 0.115,0.115 0.427,0.313 0.313,0.198 10 false *a 1.688,0.167 2,0.365 0.313,0.198 10 false H46
*a Front view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H46-1 (CANH) - H46-2 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H46-1 (CANH) - H46-29 (E) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H46-2 (CANL) - H46-29 (E) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H46-1 (CANH) - H46-6 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H46-2 (CANL) - H46-6 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




METER MIRROR SUB-ASSEMBLY (w/ Headup Display)


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H61 meter mirror sub-assembly connector.


c.
C427758C04
1.5,0.177 1.896,0.458 0.396,0.281 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 1.573,0.229 1.885,0.427 0.313,0.198 10 false H61
*a Front view of wire harness connector
(to Meter Mirror Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H61-12 (MPX1) - H61-13 (MPX2) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H61-12 (MPX1) - H61-4 (ES) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H61-13 (MPX2) - H61-4 (ES) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H61-12 (MPX1) - H61-2 (B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H61-13 (MPX2) - H61-2 (B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY (for Automatic Air Conditioning System)


Refer to Terminals of ECU.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Gasoline Model with Automatic Air Conditioning System)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H24 air conditioning amplifier assembly connector.


c.
C422314C02
1.594,0.125 2.094,0.375 0.5,0.25 0.104,0.094 0.417,0.292 0.313,0.198 10 false *a 1.719,0.167 2.031,0.365 0.313,0.198 10 false H24
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H24-2 (CANH) - H24-1 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H24-2 (CANH) - H24-17 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H24-1 (CANL) - H24-17 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H24-2 (CANH) - H24-5 (B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H24-1 (CANL) - H24-5 (B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




AIR CONDITIONING AMPLIFIER ASSEMBLY (for Manual Air Conditioning System)


Refer to Terminals of ECU.

Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Gasoline Model with Manual Air Conditioning System)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H23 air conditioning amplifier assembly connector.


c.
C425284C01
1.5,0.177 1.896,0.458 0.396,0.281 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 1.573,0.229 1.885,0.427 0.313,0.198 10 false H23
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H23-9 (CANH) - H23-26 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H23-9 (CANH) - H23-27 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H23-26 (CANL) - H23-27 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H23-9 (CANH) - H23-1 (B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H23-26 (CANL) - H23-1 (B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


Refer to Terminals of ECU.

Click hereVehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H4 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C427524C05
0.354,0.792 0.729,1.01 0.375,0.219 3.625,0.792 4,1.01 0.375,0.219 0.198,0.104 0.51,0.302 0.313,0.198 10 false *a 3.771,0.167 4.083,0.365 0.313,0.198 10 false *1 0.458,0.823 0.771,1.021 0.313,0.198 10 false H4 3.729,0.823 4.042,1.021 0.313,0.198 10 false H3
*1 DLC3 - -
*a Front view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU))
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H4-2 (CANH) - H4-1 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H4-2 (CANH) - H3-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H4-1 (CANL) - H3-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H4-2 (CANH) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H4-1 (CANL) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




COMBINATION METER ASSEMBLY


Refer to Terminals of ECU.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H6 combination meter assembly connector.


c.
C406366C59
1.479,0.167 1.979,0.417 0.5,0.25 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 1.615,0.208 1.927,0.365 0.313,0.156 10 false H6
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H6-9 (CANH) - H6-25 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
H6-9 (CANH) - H6-23 (ES) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H6-25 (CANL) - H6-23 (ES) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H6-9 (CANH) - H6-22 (B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H6-25 (CANL) - H6-22 (B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)


Refer to Terminals of ECU.


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the O60 clearance warning ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C427760C04
0.281,0.771 0.656,1.01 0.375,0.24 3.865,0.771 4.24,1.01 0.375,0.24 3.74,0.188 4.052,0.385 0.313,0.198 10 false *1 0.469,0.146 0.781,0.344 0.313,0.198 10 false *a 3.969,0.802 4.281,1 0.313,0.198 10 false H3 0.344,0.802 0.656,1 0.313,0.198 10 false O60
*1 DLC3 - -
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
O60-17 (R1) - O60-18 (R2) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
O60-17 (R1) - O60-31 (E) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O60-18 (R2) - O60-31 (E) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O60-17 (R1) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O60-18 (R2) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




FORWARD RECOGNITION CAMERA (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT CAMERA SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the V10 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

C427754C04
3.76,0.75 4.156,1 0.396,0.25 0.844,0.76 1.24,1.01 0.396,0.25 0.927,0.802 1.24,1 0.313,0.198 10 false V10 0.417,0.208 0.729,0.406 0.313,0.198 10 false *a 3.646,0.26 3.958,0.458 0.313,0.198 10 false *1 3.875,0.792 4.188,0.99 0.313,0.198 10 false H3
*1 DLC3 - -
*a Front view of wire harness connector
(to Forward Recognition Camera)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
V10-5 (CA1P) - V10-11 (CA1N) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
V10-5 (CA1P) - V10-10 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V10-11 (CA1N) - V10-10 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
V10-5 (CA1P) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
V10-11 (CA1N) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense)


Refer to Terminals of ECU.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>FRONT RADAR SENSOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the B8 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C427755C04
0.729,0.792 1.115,1.042 0.385,0.25 3.719,0.823 4.146,1.063 0.427,0.24 3.594,0.177 3.906,0.375 0.313,0.198 10 false *1 0.708,0.135 1.021,0.333 0.313,0.198 10 false *a 0.823,0.833 1.135,1.031 0.313,0.198 10 false B8 3.844,0.854 4.156,1.052 0.313,0.198 10 false H3
*1 DLC3 - -
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
B8-3 (CA2H) - B8-2 (CA2L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
B8-3 (CA2H) - B8-1 (SGND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B8-2 (CA2L) - B8-1 (SGND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B8-3 (CA2H) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
B8-2 (CA2L) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the T6 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

C427753C04
0.594,0.792 1.042,1.01 0.448,0.219 3.625,0.865 4.073,1.083 0.448,0.219 0.708,0.188 1.021,0.385 0.313,0.198 10 false *a 3.542,0.198 3.854,0.396 0.313,0.198 10 false *1 0.74,0.813 1.052,1.01 0.313,0.198 10 false T6 3.771,0.885 4.083,1.083 0.313,0.198 10 false H3
*1 DLC3 - -
*a Front view of wire harness connector
(to Blind Spot Monitor Sensor LH)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
T6-2 (CA1P) - T6-7 (CA1N) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
T6-2 (CA1P) - T6-10 (BLGD) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
T6-7 (CA1N) - T6-10 (BLGD) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
T6-2 (CA1P) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
T6-7 (CA1N) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the Y2 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

C427757C04
0.635,0.75 1.031,1.031 0.396,0.281 3.719,0.792 4.115,1.073 0.396,0.281 0.5,0.219 0.813,0.417 0.313,0.198 10 false *a 3.458,0.25 3.771,0.448 0.313,0.198 10 false *1 3.833,0.844 4.146,1.042 0.313,0.198 10 false H3 0.74,0.802 1.146,1.01 0.406,0.208 10 false Y2
*1 DLC3 - -
*a Front view of wire harness connector
(to Rear Television Camera Assembly)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
Y2-4 (CANH) - Y2-1 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
Y2-4 (CANH) - H3-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
Y2-1 (CANL) - H3-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
Y2-4 (CANH) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
Y2-1 (CANL) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




PARKING ASSIST ECU (w/ Panoramic View Monitor System )


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM (w/o Advanced Park)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the O25 parking assist ECU connector.


c.
C403821C20
1.458,0.844 1.958,1.094 0.5,0.25 1.573,0.896 1.865,1.063 0.292,0.167 10 false O25 0.094,0.094 0.708,0.292 0.615,0.198 10 false *a
*a Front view of wire harness connector
(to Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
O25-40 (CANH) - O25-18 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
O25-40 (CANH) - O25-2 (GND1) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O25-18 (CANL) - O25-2 (GND1) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O25-40 (CANH) - O25-1 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O25-18 (CANL) - O25-1 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




TELEMATICS TRANSCEIVER (w/ Telematics System for Toyota Connected Services)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H85 telematics transceiver connector.


c.
C404434C49
1.5,0.917 2,1.167 0.5,0.25 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 1.625,0.958 2.083,1.156 0.458,0.198 10 false H85
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H85-25 (CANP) - H85-26 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H85-25 (CANP) - H85-20 (E) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H85-26 (CANN) - H85-20 (E) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H85-25 (CANP) - H85-1 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H85-26 (CANN) - H85-1 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




TELEPHONE TRANSCEIVER ASSEMBLY (w/ Telematics System for eCall)


Refer to Terminals of ECU.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H85 telematics transceiver connector.


c.
C404434C48
1.5,0.917 2,1.167 0.5,0.25 0.135,0.104 0.448,0.26 0.313,0.156 10 false *a 1.625,0.958 2.083,1.156 0.458,0.198 10 false H85
*a Front view of wire harness connector
(to Telephone Transceiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H85-25 (CANP) - H85-26 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H85-25 (CANP) - H85-20 (E) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H85-26 (CANN) - H85-20 (E) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H85-25 (CANP) - H85-1 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H85-26 (CANN) - H85-1 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door)


Refer to Terminals of ECU.

Click hereVehicle Exterior>DOOR / HATCH>POWER BACK DOOR SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the Y30 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

C446922C02
0.719,0.781 1.219,1.031 0.5,0.25 3.583,0.781 4.083,1.031 0.5,0.25 0.24,0.135 0.552,0.333 0.313,0.198 10 false *a 3.76,0.156 4.073,0.354 0.313,0.198 10 false *1 0.844,0.813 1.156,1.01 0.313,0.198 10 false Y30 3.75,0.823 4.063,1.021 0.313,0.198 10 false H3
*1 DLC3 - -
*a Front view of wire harness connector
(to Multiplex Network Door ECU)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
Y30-10 (CANP) - Y30-20 (CANN) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω
Y30-10 (CANP) - H3-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
Y30-20 (CANN) - H3-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
Y30-10 (CANP) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
Y30-20 (CANN) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




ENGINE STOP AND START ECU (w/ Stop and Start System)


Refer to Terminals of ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the H43 engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

C430928C01
0.552,0.75 0.948,1.031 0.396,0.281 3.823,0.792 4.219,1.073 0.396,0.281 0.5,0.219 0.813,0.417 0.313,0.198 10 false *a 3.458,0.25 3.771,0.448 0.313,0.198 10 false *1 3.917,0.833 4.229,1.031 0.313,0.198 10 false H3 0.615,0.802 1.073,1.021 0.458,0.219 10 false H43
*1 DLC3 - -
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -


Standard Resistance:
Bus 2 Branch Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H43-13 (CANH) - H43-14 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H43-13 (CANH) - H3-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H43-14 (CANL) - H3-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H43-13 (CANH) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H43-14 (CANL) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


Chassis Local Bus Main Lines
Terminal No. (Symbol) Terminal Description Condition Specified Condition
H43-15 (LC1H) - H43-16 (LC1L) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
H43-15 (LC1H) - H3-4 (CG) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H43-16 (LC1L) - H3-4 (CG) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
H43-15 (LC1H) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
H43-16 (LC1L) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



TIRE PRESSURE WARNING ECU AND RECEIVER (w/ Tire Pressure Warning System)


Refer to Terminals of ECU.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the O33*1 or O34*2 tire pressure warning ECU and receiver connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



c.
C427521C12
0.333,1 0.833,1.25 0.5,0.25 0.333,1.354 0.833,1.604 0.5,0.25 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 0.448,1.031 0.792,1.292 0.344,0.26 10 false O33 0.865,1.021 1.156,1.281 0.292,0.26 12 false *A 0.448,1.396 0.792,1.656 0.344,0.26 10 false O34 0.875,1.396 1.198,1.708 0.323,0.313 12 false *B
*A w/o Entry and Start System
*B w/ Entry and Start System
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Entry and Start System
Terminal No. (Symbol) Terminal Description Condition Specified Condition
O33-9 (CANH) - O33-10 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
O33-9 (CANH) - O33-12 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O33-10 (CANL) - O33-12 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O33-9 (CANH) - O33-7 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O33-10 (CANL) - O33-7 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher


w/ Entry and Start System
Terminal No. (Symbol) Terminal Description Condition Specified Condition
O34-9 (CANH) - O34-10 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
O34-9 (CANH) - O34-12 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O34-10 (CANL) - O34-12 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
O34-9 (CANH) - O34-7 (+B) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
O34-10 (CANL) - O34-7 (+B) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



HEADLIGHT ECU SUB-ASSEMBLY LH (w/ Adaptive High Beam System)


Refer to Terminals of ECU.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>ADAPTIVE HIGH BEAM SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A110 headlight ECU sub-assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

C442099C06
0.167,0.813 0.563,1.115 0.396,0.302 3.781,0.76 4.156,1.073 0.375,0.313 0.313,0.156 0.625,0.354 0.313,0.198 10 false *a 3.698,0.198 4.01,0.396 0.313,0.198 10 false *1 0.208,0.885 0.594,1.083 0.385,0.198 10 false A110 3.885,0.833 4.198,1.031 0.313,0.198 10 false H3
*1 DLC3 - -
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly LH)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A110-24 (CANH) - A110-23 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A110-24 (CANH) - A110-12 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A110-23 (CANL) - A110-12 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A110-24 (CANH) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A110-23 (CANL) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher




HEADLIGHT ECU SUB-ASSEMBLY RH (w/ Adaptive High Beam System)


Refer to Terminals of ECU.

Click hereADAS / AD>ADVANCED DRIVER ASSISTANCE SYSTEM>ADAPTIVE HIGH BEAM SYSTEM>TERMINALS OF ECU

a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the A111 headlight ECU sub-assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

C442099C07
0.177,0.823 0.552,1.135 0.375,0.313 3.781,0.76 4.156,1.073 0.375,0.313 0.313,0.156 0.625,0.354 0.313,0.198 10 false *a 3.698,0.198 4.01,0.396 0.313,0.198 10 false *1 0.208,0.885 0.573,1.094 0.365,0.208 10 false A111 3.875,0.833 4.188,1.031 0.313,0.198 10 false H3
*1 DLC3 - -
*a Front view of wire harness connector
(to Headlight ECU Sub-assembly RH)
- -


Standard Resistance:
Terminal No. (Symbol) Terminal Description Condition Specified Condition
A111-24 (CANH) - A111-23 (CANL) HIGH-level CAN bus line - LOW-level CAN bus line Cable disconnected from negative (-) auxiliary battery terminal 54 to 69 Ω
A111-24 (CANH) - A111-12 (GND) HIGH-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A111-23 (CANL) - A111-12 (GND) LOW-level CAN bus line - Ground Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
A111-24 (CANH) - H3-16 (BAT) HIGH-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
A111-23 (CANL) - H3-16 (BAT) LOW-level CAN bus line - Auxiliary battery positive (+) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher