| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 1 | TRANSMISSION CONTROL CABLE ASSEMBLY | 33820B | ( )
|
- | - |
| 2 | REAR CONSOLE BOX ASSEMBLY | 58910C | - | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 3 | FRONT NO. 1 FLOOR HEAT INSULATOR | 58153 | - | - | - |
| 4 | FRONT NO. 2 FLOOR HEAT INSULATOR | 58151 | - | - | - |
| *A | for TMC Made | *B | for TMMF Made |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 5 | FRONT EXHAUST PIPE ASSEMBLY | 17410 | ( )
|
- | - |
| 6 | CENTER NO. 1 FLOOR BRACE | 57543C | - | - | - |
| 7 | CENTER NO. 4 ENGINE UNDER COVER | 51447D | - | - | - |
| *A | for 2WD | *B | for AWD |
| *C | for TMC Made | *D | for TMMF Made |
|
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| Procedure | Part Name Code |
|
|
|
|
|---|---|---|---|---|---|
| 8 | FRONT FLOOR COVER LH | 58166A | - | - | - |
| 9 | FRONT FLOOR COVER RH | 58165C | - | - | - |
| *A | for TMMF Made | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
|
N*m (kgf*cm, ft.*lbf): Specified torque | - | - |
33820B
1.INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY
|
|
Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.
Engage the guide to connect the transmission control cable assembly to vehicle body.
Install the nut.
Install the transmission control cable assembly to the hybrid vehicle transaxle assembly with the bolt.
Engage the clamp to connect the transmission control cable assembly.
Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip.
Turn the control shaft lever clockwise until it stops, and then from that position turn it counterclockwise by 2 notches to set it to the N position.
Connect the transmission control cable assembly to the control shaft lever with the nut.
| *1 | Adjuster Case | *2 | Adjuster Case Cover |
| *3 | Lock Piece | - | - |
Slide the adjuster case cover in the direction shown by the arrow.
Using a precision screwdriver, pull out the lock piece of the adjuster case.
| *1 | Lock Nut | *2 | Stopper |
| *a | Push in | - | - |
Turn the lock nut of the transmission control cable assembly counterclockwise. While holding the lock nut, push in the stopper.
Connect the transmission control cable assembly to the transmission floor shift assembly.
After installation, check that the outer part of the stopper is as shown in the illustration.
Do not forcibly pull the transmission control cable assembly into the cabin.
Connect the transmission control cable assembly to the transmission floor shift assembly.
Push the end of the transmission control cable assembly all the way to the base of the transmission floor shift assembly pin.
Connect the transmission control cable assembly so that the lock piece faces the driver side.
Before connecting the floor shift transmission control select cable, check that the shift lever is in N.
| *1 | Adjuster Case | *2 | Lock Piece |
| *3 | Adjuster Case Cover | - | - |
Push in the lock piece of the adjuster case to lock it.
| *1 | Transmission Control Cable Assembly |
| *2 | Lever Shaft |
When pushing in the lock piece of the adjuster case to lock it, remove your hand from the lever shaft.
When pushing in the lock piece of the adjuster case to lock it, do not move the lever shaft or transmission control cable assembly forward or backward.
Move the adjuster case cover in the direction shown by the arrow.
If the adjuster case cover is not moved far enough so that the adjuster case cover engages the lock piece, the cable will not be able to lock, and reliable shift operation will not be possible.
58910C
2.INSTALL REAR CONSOLE BOX ASSEMBLY
58151
3.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR
58153
4.INSTALL FRONT NO. 2 FLOOR HEAT INSULATOR
57543C
6.INSTALL CENTER NO. 1 FLOOR BRACE (for TMMF Made)
51447D
7.INSTALL CENTER NO. 4 ENGINE UNDER COVER
58166A
8.INSTALL FRONT FLOOR COVER LH (for TMMF Made)
58165C
9.INSTALL FRONT FLOOR COVER RH (for TMMF Made)
G92A0
10.INSTALL HYBRID MOTOR CONTROL INVERTER ASSEMBLY
11.INSPECT SHIFT LEVER POSITION
for TMMF Made: Click hereDrivetrain>P910 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT LEVER (for TMMF Made)>ON-VEHICLE INSPECTION
12.ADJUST SHIFT LEVER POSITION
13.INSPECT FOR EXHAUST GAS LEAK
51410
14.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY