Refer to DTC P0031 (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0031).
Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0133 | While idling with warm engine, response time for voltage output of heated oxygen sensor to change from rich to lean or from lean to rich is 1 second or more (2 trip detection logic) | ·
Open or short in heated oxygen sensor (sensor 1) circuit ·
Heated oxygen sensor (sensor 1) ·
Heated oxygen sensor heater (sensor 1) ·
No. 1 integration relay (EFI MAIN relay) ·
Intake system ·
Fuel pressure ·
Fuel injector assembly ·
ECM |
The ECM uses the heated oxygen sensor information to regulate the air-fuel ratio close to the stoichiometric air-fuel ratio. This maximizes the catalytic converter's ability to purify the exhaust gases. The sensor detects oxygen levels in the exhaust gas and sends a signal to the ECM.
The inner surface of the sensor element is exposed to outside air. The outer surface of the sensor element is exposed to the exhaust gases. The sensor element is made of platinum coated zirconia and includes an integrated heating element. The heated oxygen sensor's output voltage changes suddenly in the vicinity of the stoichiometric air-fuel ratio. The heated oxygen sensor generates waveforms of a voltage between 0 V and 1 V in response to the oxygen concentration in the exhaust gas. When the heated oxygen sensor voltage is 0.45 V or more, the ECM judges that the air-fuel ratio is rich. When it is 0.45 V or less, the ECM judges that the air-fuel ratio is lean. The ECM monitors the response feature of the heated oxygen sensor. If the response time of the heated oxygen sensor status change from rich to lean (or vice versa) becomes longer, the ECM interprets this as a malfunction in the heated oxygen sensor and stores a DTC.
| Required Sensors/Components (Main) | Heated oxygen sensor (sensor 1) |
| Required Sensors/Components (Related) | Mass air flow meter, Throttle with motor body assembly, Crankshaft position sensor, Vehicle speed sensor |
| Frequency of Operation | Once per driving cycle |
| Duration that vehicle has run with the following conditions A and B | 15 seconds or more |
| A. Vehicle speed | 40 km/h (24 mph) or more |
| B. Engine speed | 900 rpm or more |
| Time after engine start | 120 seconds or more |
| Idle | ON |
| Fuel system status | Closed loop |
| Vehicle speed | Less than 5 km/h (3 mph) |
| Engine coolant temperature | 75°C (167°F) or more |
| One of the following conditions is met | - |
| Average of switch time from lean to rich* | 1 second or more |
| Average of switch time from rich to lean* | 1 second or more |
| * Lean | 0.4 V or lower |
| * Rich | 0.5 V or higher |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the tester on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
Allow the engine and idle it for 120 seconds or more [B].
Drive the vehicle at 40 km/h (24 mph) or more for 35 seconds [C].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Idle the engine for 40 seconds or more [D].
Perform step [C] and [D] at least 3 times.
Enter the following menus: Powertrain / Engine and ECT / DTC [E].
Read pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0133.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E].
Refer to DTC P0031 (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>P0031).
Malfunctioning areas can be identified by performing the Control the Injection Volume function provided in the Active Test. The Control the Injection Volume function can help to determine whether the heated oxygen sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume operation using the intelligent tester.
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Perform the Active Test operation with the engine idling.
Monitor the output voltages of the heated oxygen sensors (O2S B1S1 and O2S B1S2) displayed on the tester.
Change the fuel injection volume within the range of -12% to +12%. The injection volume can be changed in fine gradations.
Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
| Tester Display
(Sensor) |
Injection Volume | Status | Voltage |
|---|---|---|---|
| O2S B1S1
(Heated oxygen sensor (sensor 1)) |
+12% | Rich | Higher than 0.5 V |
| -12% | Lean | Below 0.4 V | |
| O2S B1S2
(Heated oxygen sensor (sensor 2)) |
+12% | Rich | Higher than 0.5 V |
| -12% | Lean | Below 0.4 V |
The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.
Following the Control the Injection Volume procedure enables technicians to check and graph the voltage outputs of both the heated oxygen sensors
To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / O2S B1S1 and O2S B1S2; then press the view button.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
|---|---|
| DTC P0133 is output | A |
| DTC P0133 and other DTCs are output | B |
If any DTCs other than P0133 are output, troubleshoot those DTCs first.
A
B
(See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>DIAGNOSTIC TROUBLE CODE CHART)
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / O2S B1S1.
Warm up the heated oxygen sensor at an engine speed of 2500 rpm for approximately 90 seconds.
Read the voltage output of the front heated oxygen sensor displayed on the tester, while the engine is idling.
Fluctuates between less than 0.4 V and more than 0.5 V, and period "t" is less than 1 second (refer to table below).
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Inspect the heated oxygen sensor (sensor 1) (See page Engine / Hybrid System>1NZ-FE ENGINE CONTROL>HEATED OXYGEN SENSOR(for Sensor 1)>INSPECTION).
OK
NG
Disconnect the heated oxygen sensor (sensor 1) connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B37-2 (+B) -Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Heated Oxygen Sensor (Sensor 1)) |
OK
NG
Disconnect the heated oxygen sensor (sensor 1) connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B37-1 (HT1A) - B84-109 (HT1A) | Always | Below 1 Ω |
| B37-3 (OX1A) - B84-112 (OX1A) | Always | Below 1 Ω |
| B37-4 (E2) - B84-90 (EX1A) | Always | Below 1 Ω |
| B37-1 (HT1A) or B84-109 (HT1A) - Body ground | Always | 10 kΩ or higher |
| B37-3 (OX1A) or B84-112 (OX1A) - Body ground | Always | 10 kΩ or higher |
| B37-4 (E2) or B84-90 (EX1A) - Body ground | Always | 10 kΩ or higher |
OK
NG
Check the intake system for vacuum leaks.
No leakage from intake system.
OK
NG
Check the fuel pressure (See page Engine / Hybrid System>1NZ-FE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).
OK
NG
Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor) (See page Engine / Hybrid System>1NZ-FE FUEL>FUEL INJECTOR>INSPECTION).
OK
NG
Disconnect the heated oxygen sensor (sensor 1) connector.
Remove the No. 1 integration relay connector from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B37-2 (+B) - 1E-4 | Always | Below 1 Ω |
OK
NG
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0133 is output | A |
| DTC is not output | B |
A
B
(See pageEngine / Hybrid System>1NZ-FE ENGINE CONTROL>1NZ-FE SFI SYSTEM>CHECK FOR INTERMITTENT PROBLEMS)