Home › Engine / Hybrid System › 1NZ-FE ENGINE CONTROL › 1NZ-FE SFI SYSTEM › 2016.09–2017.01
RM19S0E _51 Engine / Hybrid System _051448 1NZ-FE ENGINE CONTROL _0248039 1NZ-FE SFI SYSTEM C

1NZ-FE ENGINE CONTROL  1NZ-FE SFI SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The stop light switch is part of a duplex system that transmits 2 signals: STP and ST1-. These 2 signals are used by the ECM to monitor whether or not the brake system is working properly. This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0724 Stop light switch assembly remains ON even when vehicle repeats 5 cycles of STOP (less than 3 km/h [1.86 mph]) and GO (30 km/h [18.64 mph] or more)
(2 trip detection logic)
·

Short in stop light switch assembly signal circuit

·

Stop light switch assembly

·

ECM



MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC. The vehicle must GO (30 km/h (18.64 mph) or more) and STOP (less than 3 km/h (1.86 mph)) 5 times for 2 driving cycles in order for the DTC to be stored.

MONITOR STRATEGY

Required Sensors/Components Stop light switch assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A199312E35
1.414,2.021 1.792,2.191 0.378,0.170 10 Idling 0.61,2.352 1.882,2.679 1.272,0.327 10 Ignition Switch ON 2.509,2.467 2.707,2.665 0.198,0.198 10 [A] 2.583,3.079 3.295,3.221 0.711,0.142 10 5 seconds 3.27,3.494 3.474,3.674 0.205,0.180 10 [B] 3.409,1.912 3.619,2.090 0.210,0.178 10 [C] 6.755,3.475 6.953,3.672 0.198,0.198 10 [E] 4.043,1.495 4.253,1.673 0.210,0.178 10 [D] 0.479,1.201 1.827,1.385 1.348,0.184 10 30 km/h (18.64 mph) 0.631,1.726 1.867,1.903 1.237,0.177 10 3 km/h (1.86 mph)

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Wait 5 seconds.

7.

Enter the following menus: Powertrain / Engine and ECT / DTC [B].

8.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



9.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

10.

Input the DTC: P0724.

11.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E].



12.

Start the engine [C].

13.

Accelerate the vehicle to 30 km/h (18.64 mph) or more, and then depress the brake pedal and decelerate the vehicle to 3 km/h (1.86 mph) or less [D]. Repeat step [D] 5 times.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Check the DTC judgment result [E].


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Using the GTS, the Data List item "Stop Light Switch" can be read.



Item Measurement Item/Range Normal Condition Diagnostic Note
Stop Light Switch Stop light switch status/
ON or OFF
·

Brake pedal depressed: ON

·

Brake pedal released: OFF


-

PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.


d.

Check the STP signal when the brake pedal is depressed and released.


Brake Pedal Operation Stop Light Switch
Depressed ON
Released OFF


OK

NG

2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
2.CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Check the stop light switch assembly installation.

OK:

Stop light switch assembly is installed correctly.




OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

SECURELY REINSTALL STOP LIGHT SWITCH ASSEMBLY

3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the A81 stop light switch assembly connector.


b.

Disconnect the A83 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A81-3 - A83-10 (ST1-) Always Below 1 Ω
A81-1 - A83-9 (STP) Always Below 1 Ω
A81-3 or A83-10 (ST1-) - Body ground Always 10 kΩ or higher
A81-1 or A83-9 (STP) - Body ground Always 10 kΩ or higher



OK

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY (STOP CONTROL RELAY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 1 INTEGRATION RELAY (STOP CONTROL RELAY))
a.

Remove the STOP fuse from the junction block assembly.


b.

Disconnect the A81 stop light switch assembly connector.


c.

Remove the No. 1 integration relay from the engine room relay block.


d.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
A81-2 - 1E-6 Always Below 1 Ω
A81-1 - 1D-2 Always Below 1 Ω
A81-2 or 1E-6 - Body ground Always 10 kΩ or higher
A81-1 or 1D-2 - Body ground Always 10 kΩ or higher



OK

6.INSPECT NO. 1 INTEGRATION RELAY (STOP CONTROL RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT NO. 1 INTEGRATION RELAY (STOP CONTROL RELAY)
a.
U158068C01
0.167,0.063 0.906,0.385 0.74,0.323 10 false *a 0.74,1.292 1.063,1.49 0.323,0.198 10 false A81
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Disconnect the stop light switch assembly connector.


b.

Disconnect the A83 ECM connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A81-1 - Body ground Always Below 1.5 V




OK

NG