Home › Engine / Hybrid System › 2NZ-FE ENGINE CONTROL › SFI SYSTEM › from 2016.09
RM19S0E _51 Engine / Hybrid System _051449 2NZ-FE ENGINE CONTROL _0248054 SFI SYSTEM C

2NZ-FE ENGINE CONTROL  SFI SYSTEM  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  P102D  O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON  


DESCRIPTION

Refer to DTC P0136

Click hereEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>P0136

HINT:
·

When any of these DTCs are set, the ECM enters fail-safe mode. The ECM turns off the heated oxygen sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.

·

The ECM uses pulse width modulation to adjust the current through the heater. The heated oxygen sensor heater circuit uses a relay on the +B side of the circuit.

A327377E03
0.115,0.052 3.49,0.458 3.375,0.406 12 false Reference (System Diagram of Sensor 2): 0.156,1.115 0.625,1.635 0.469,0.521 10 false from Battery 0.792,1.292 1.438,1.438 0.646,0.146 10 false EFI MAIN 1.781,2.385 2.427,2.531 0.646,0.146 10 false EFI MAIN 2.74,1.292 3.375,1.438 0.635,0.146 10 false EFI No. 2 0.729,3.292 1.229,3.438 0.5,0.146 10 false Ground 3.865,0.823 4.323,1.052 0.458,0.229 10 false Heater 3.865,1.396 4.344,1.625 0.479,0.229 10 false Sensor 3.469,1.052 3.667,1.198 0.198,0.146 10 false +B 3.469,1.604 3.667,1.75 0.198,0.146 10 false E2 4.521,1.052 4.927,1.198 0.406,0.146 10 false HT1B 4.521,1.604 4.927,1.75 0.406,0.146 10 false OX1B 5.115,1.052 5.521,1.198 0.406,0.146 10 false HT1B 5.115,2.188 5.51,2.333 0.396,0.146 10 false EX1B 5.115,2.76 5.521,2.906 0.406,0.146 10 false MREL 5.115,1.604 5.521,1.75 0.406,0.146 10 false OX1B 3.49,2.031 4.979,2.396 1.49,0.365 10 false Heated Oxygen Sensor 5.906,3.438 6.24,3.615 0.333,0.177 10 false ECM



DTC No. DTC Detection Condition Trouble Area
P0037 Heated oxygen sensor heater current is the specified value or less while the heater is operating.
(1 trip detection logic).
·

Open in heated oxygen sensor heater circuit

·

Heated oxygen sensor heater

·

No. 1 integration relay (EFI MAIN relay)

·

ECM


P0038 Heated oxygen sensor heater current reaches high limit (Hybrid IC high current limiter monitor input "Fail")
(1 trip detection logic).
·

Short in heated oxygen sensor heater circuit

·

Heated oxygen sensor heater

·

No. 1 integration relay (EFI MAIN relay)

·

ECM


P102D The heated oxygen sensor heater current is higher than a specified value while the heater is not operating. (1 trip detection logic)
(1 trip detection logic).
ECM

MONITOR DESCRIPTION

The sensing portion of the heated oxygen sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated oxygen sensor heater range check (P0037, P0038 and P102D):

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.


HINT:

Normally, the heated oxygen sensor current is 0.4 to 1 A (when the engine is idling, the heated oxygen sensor is warmed up and battery voltage is 11 to 14 V).


CONFIRMATION DRIVING PATTERN

A198819E21
0.75,0.969 1.396,1.162 0.647,0.193 10 3000 rpm 1.011,1.717 1.417,1.878 0.406,0.161 10 Idling 0.196,2.028 1.442,2.239 1.246,0.211 10 Ignition Switch ON 1.926,2.132 2.161,2.297 0.235,0.165 10 [A] 2.762,1.622 2.955,1.815 0.193,0.193 10 [B] 4.026,0.868 4.283,1.006 0.258,0.137 10 [C] 5.39,1.6 5.614,1.782 0.223,0.181 10 [D] 2.272,2.589 3.465,2.745 1.193,0.156 10 5 minutes or more 4.873,2.608 6.066,2.764 1.193,0.156 10 5 minutes or more 3.851,2.617 4.423,2.782 0.573,0.165 10 1 minute 5.98,3.028 6.182,3.230 0.202,0.202 10 [E]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and idle it for 5 minutes or more [B].

7.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of 3000 rpm for 1 minute [C].

8.

Idle the engine for 5 minutes or more [D].

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0037, P0038 or P102D.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


UNKNOWN
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or UNKNOWN, perform steps [B] through [E] again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Refer to "Data List / Active Test [O2 Heater B1S2, O2 Heater Curr Val B1S2] (See page Engine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).

·

When the values for the Data List item O2 Heater Curr Val B1S2 is not 0 A, the heater is on.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
a.
A326245C01
1.938,1.156 2.354,0.76 true 1.094,1.823 1.5,1.438 true 1.479,1.167 1.063,0.771 true 2.417,0.635 2.813,0.875 0.396,0.24 10 false HT1B 0.771,0.625 1,0.865 0.229,0.24 10 false +B 0.104,0.052 0.333,0.292 0.229,0.24 10 false *a 0.865,1.823 1.094,2.063 0.229,0.24 10 false E2
*a Component without harness connected
(Heated Oxygen Sensor)


Disconnect the F137 heated oxygen sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (HT1B) - 2 (+B) 20°C (68°F) 9 to 14 Ω
1 (HT1B) - 4 (E2) Always 10 kΩ or higher



HINT:

Perform "Inspection After Repair" after replacing the heated oxygen sensor (See pageEngine / Hybrid System>2NZ-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE)

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE)
a.
U126565C02
1.875,0.958 2.417,0.417 true 0.469,1.083 0.802,1.25 0.333,0.167 10 false F137 2.469,0.292 2.729,0.469 0.26,0.177 10 false +B 0.104,0.094 0.344,0.281 0.24,0.188 10 false *a
*a Front view of wire harness connector
(to Heated Oxygen Sensor)


Disconnect the heated oxygen sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F137-2 (+B) - Body ground Ignition switch ON 11 to 14 V




OK

3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)

NG

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM)
a.

Disconnect the F137 heated oxygen sensor connector.


b.

Disconnect the B89 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F137-1 (HT1B) - B89-22 (HT1B) Always Below 1 Ω


Standard Resistance:
Tester Connection Condition Specified Condition
F137-1 (HT1B) or B89-22 (HT1B) - Body ground Always 10 kΩ or higher




OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038 OR P102D)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (HEATED OXYGEN SENSOR - ECM)

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038 OR P102D)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Start the engine and idle it for 5 minutes or more.


f.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed 3000 rpm for 1 minute.


g.

Idle the engine for 5 minutes or more.


h.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


i.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P0037, P0038 or P102D is output B




A

B

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - NO. 1 INTEGRATION RELAY)
a.

Disconnect the F137 heated oxygen sensor connector.


b.

Remove the No. 1 integration relay from the engine room main relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F137-2 (+B) - 1D-11 Always Below 1 Ω


Standard Resistance:
Tester Connection Condition Specified Condition
F137-2 (+B) or 1D-11 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR