Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › from 2017.01
RM19S0E _58 Vehicle Interior _063185 PRE-CRASH SAFETY _0307822 PRE-CRASH SAFETY SYSTEM J

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  Pre-crash Safety System Switch Circuit  


DESCRIPTION

Each time the pre-crash safety system cancel switch assembly is pressed, the LCD display sensitivity setting display changes to switch the sensitivity of the pre-crash safety system between 3 levels. Also, when the switch is pressed and held, the pre-crash safety system cancels.

WIRING DIAGRAM

E297408E61
5.198,2.031 5.563,2.24 0.365,0.208 10 false L11 5.198,2.188 7.115,2.521 1.917,0.333 10 false Pre-crash Safety City Sensor 5.521,1.042 6.042,1.188 0.521,0.146 10 false PCSW 5.323,0.927 5.49,1.094 0.167,0.167 10 false 9 3.583,0.927 3.896,1.104 0.313,0.177 10 false ECU 3.979,0.927 4.146,1.094 0.167,0.167 10 false 4 2.677,0.927 2.99,1.104 0.313,0.177 10 false GND 2.479,0.927 2.646,1.094 0.167,0.167 10 false 1 2.406,1.448 2.802,1.615 0.396,0.167 10 false F140 2.406,1.604 3.99,2.031 1.583,0.427 10 false Pre-crash Safety System Cancel Switch Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the pre-crash safety city sensor, replace it with a new one. If an ECU which was installed to another vehicle is used, the information stored in the pre-crash safety city sensor will not match the information from the vehicle and, as a result, a DTC may be output.

·

If the pre-crash safety city sensor has been replaced, or the windshield glass has been replaced or removed/installed, be sure to perform Recognition Camera/Target Position Memory and Recognition Camera Axis Adjust.

·

Perform adjustment using "ONE TIME RECOGNITION" or "SEQUENTIAL RECOGNITION".



PROCEDURE

1.READ VALUE USING GTS (PCS Operation State Retention Setting)
a.

Read the Data List according to the display on the GTS (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST).

PCS/LDA/RSA/LVN
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
PCS Operation State Retention Setting Displays pre-crash safety system operation status retained settings / ON or OFF ON: PCS Operation State Retention Setting customize setting is set to ON
OFF: PCS Operation State Retention Setting customize setting is set to OFF
-
PCS Alarm Activation Distance Retention Setting 1 Displays status of pre-crash safety warning operation distance retention setting 1 / ON or OFF ON: Pre-crash safety system warning operation distance "far"
OFF: Pre-crash safety system warning operation distance other than "far"
-
PCS Alarm Activation Distance Retention Setting 2 Displays status of pre-crash safety warning operation distance retention setting 2 / ON or OFF ON: Pre-crash safety system warning operation distance "normal"
OFF: Pre-crash safety system warning operation distance other than "normal"
-
PCS Alarm Activation Distance Retention Setting 3 Displays status of pre-crash safety warning operation distance retention setting 3 / ON or OFF ON: Pre-crash safety system warning operation distance "near"
OFF: Pre-crash safety system warning operation distance other than "near"
-

HINT:

Refer to the OPERATION CHECK for operation of the of pre-crash safety system cancel switch assembly (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>OPERATION CHECK).


Result
Result Proceed to
Pressing the pre-crash safety system cancel switch assembly turns the pre-crash safety system on and off and switches the operation distance A
Pressing the pre-crash safety system cancel switch assembly does not turn the pre-crash safety system on and off and switch the operation distance B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT PRE-CRASH SAFETY SYSTEM CANCEL SWITCH ASSEMBLY
2.INSPECT PRE-CRASH SAFETY SYSTEM CANCEL SWITCH ASSEMBLY
a.

Remove the pre-crash safety system cancel switch assembly (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH BRAKE CANCEL SWITCH>REMOVAL).


b.

Inspect the pre-crash safety system cancel switch assembly (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH BRAKE CANCEL SWITCH>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (PRE-CRASH SAFETY SYSTEM CANCEL SWITCH ASSEMBLY - PRE-CRASH SAFETY CITY SENSOR AND BODY GROUND)

NG

REPLACE PRE-CRASH SAFETY SYSTEM CANCEL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (PRE-CRASH SAFETY SYSTEM CANCEL SWITCH ASSEMBLY - PRE-CRASH SAFETY CITY SENSOR AND BODY GROUND)
a.

Disconnect the F140 pre-crash safety system cancel switch assembly connector.


b.

Disconnect the L11 pre-crash safety city sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F140-4 (ECU) - L11-9 (PCSW) Always Below 1 Ω
F140-1 (GND) - Body ground Always Below 1 Ω
F140-4 (ECU) - Body ground Always 10 kΩ or higher




OK

REPLACE PRE-CRASH SAFETY CITY SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR