Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › ENGINE › 2013.08–2016.07
RM30M0E _51 Engine / Hybrid System _017073 1NZ-FE ENGINE MECHANICAL _0090998 ENGINE G

1NZ-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 17801 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner cap with No. 1 air cleaner hose.

Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>THROTTLE BODY>REMOVAL


b.

Remove the air cleaner filter element sub-assembly.


c.

Visually check that there is no dirt, blockage, or damage to the air cleaner filter element sub-assembly.

HINT:
·

If there is any dirt or a blockage in the air cleaner filter element sub-assembly, clean it with compressed air.

·

If any dirt or a blockage remains even after cleaning the air cleaner filter element sub-assembly with compressed air, replace it.




d.

Install the air cleaner filter element sub-assembly.


e.

Install the air cleaner cap with No. 1 air cleaner hose.

Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>THROTTLE BODY>INSTALLATION


Hide 16361A 5.INSPECT FAN AND GENERATOR V BELT

Hide 7.INSPECT IGNITION TIMING

a.

When using the GTS:

i.

Warm up the engine.


ii.

Turn all the electrical systems and the A/C off.


iii.

Turn the ignition switch off.


iv.

Connect the GTS to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the GTS on.


vii.

Start the engine.


viii.

Enter the following menus:

Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / ON.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

ix.

Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

Powertrain > Engine and ECT > Data List
Tester Display
IGN Advance
50003 234 29

x.

Inspect the ignition timing at idle.

Standard Ignition Timing:
Transaxle Ignition Timing
Manual Transaxle 8 to 12 degrees BTDC
Automatic Transaxle


NOTICE:
·

Inspect the ignition timing with the cooling fan off.

·

When checking the ignition timing, shift the transaxle to the neutral position.




xi.

Enter the following menus:

Powertrain / Engine and ECT / Active Test / Connect the TC and TE1 / OFF.


xii.

Turn the ignition switch off.


xiii.

Disconnect the GTS from the DLC3.



b.

When not using the GTS:

i.

ii.
A111160

Pull out the wire harness (brown) shown in the illustration.

NOTICE:

After checking, wrap the wire harness with tape.



iii.

Warm up the engine.


iv.

Turn all the electrical systems and the A/C off.


v.

Turn the ignition switch off.


vi.

Connect the clip of the timing light to the wire harness (brown).

NOTICE:

Use a timing light that detects the first signal.



vii.
A206183C30
1.583,0.906 1.313,0.542 true 1.771,1.479 2.063,1.823 true 1.01,0.406 1.292,0.604 0.281,0.198 10 false CG 2.156,1.771 2.417,1.948 0.26,0.177 10 false TC 0.094,0.083 0.406,0.24 0.313,0.156 10 false *1
*1 DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.



viii.

Start the engine.


ix.

Inspect the ignition timing at idle.

Standard Ignition Timing:
Transaxle Ignition Timing
Manual Transaxle 8 to 12 degrees BTDC
Automatic Transaxle


NOTICE:
·

Inspect the ignition timing with the cooling fan off.

·

When checking the ignition timing, shift the transaxle to the neutral position.




x.

Turn the ignition switch off.


xi.

Remove the timing light.


xii.

xiii.

Disconnect SST from terminals 13 (TC) and 4 (CG) of the DLC3.



Hide 8.INSPECT ENGINE IDLING SPEED

a.

When using the GTS:

i.

Warm up the engine.


ii.

Turn all the electrical systems and the A/C off.


iii.

Turn the ignition switch off.


iv.

Connect the GTS to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the GTS on.


vii.

Start the engine.


viii.

Enter the following menu items: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

ix.

Inspect the engine idle speed.

Standard Idling Speed:
Transaxle Idling Speed
Manual Transaxle 600 to 700 rpm
Automatic Transaxle 650 to 750 rpm


NOTICE:
·

Inspect the engine idling speed with the cooling fan off.

·

When checking the engine idling speed, shift the transaxle to the neutral position or the park position.




x.

Turn the ignition switch off.


xi.

Disconnect the GTS from the DLC3.



b.

When not using the GTS.

i.

Warm up the engine.


ii.

Turn all the electrical systems and the A/C off.


iii.

Turn the ignition switch off.


iv.
A206183C31
1.052,1.469 0.813,1.76 true 0.625,1.833 0.969,2.021 0.344,0.188 10 false TAC 0.104,0.104 0.417,0.26 0.313,0.156 10 false *1
*1 DLC3


Using SST, connect terminal 9 (TAC) of the DLC3.

SST
09843-18040  

NOTICE:

Examine the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.



v.

Connect a tachometer.


vi.

Start the engine.


vii.

Inspect the engine idle speed.

Standard Idling Speed:
Transaxle Idling Speed
Manual Transaxle 600 to 700 rpm
Automatic Transaxle 650 to 750 rpm


NOTICE:
·

Inspect the engine idling speed with the cooling fan off.


·

When checking the engine idling speed, shift the transaxle to the neutral position or the park position.




viii.

Turn the ignition switch off.


ix.

Disconnect the tachometer.


x.

Disconnect SST from terminal 9 (TAC) of the DLC3.



Hide 10.INSPECT COMPRESSION

a.

Warm up and stop the engine.



c.

Disconnect the 4 fuel injector assembly connectors.


d.
A116195

Inspect the cylinder compression pressure.

i.

Insert a compression gauge into the spark plug hole.


ii.

Fully open the throttle.


iii.

While cranking the engine, measure the compression pressure.

Compression:

980 kPa (10.0 kgf/cm2, 142 psi)


Minimum pressure:

784 kPa (8.0 kgf/cm2, 114 psi)


Difference between each cylinder:

98 kPa (1.0 kgf/cm2, 14 psi) or less


NOTICE:
·

Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression in as short a time as possible.




iv.

If the cylinder compression is low, pour a light coat of engine oil into the cylinder through the spark plug hole, then inspect it again.

HINT:
·

If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.

·

If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.





e.

Connect the 4 fuel injector assembly connectors.




Hide 11.INSPECT CO/HC

a.

Warm up the engine.


b.

Run the engine at 2500 rpm for approximately 180 seconds.


c.

Insert the CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe while idling.


d.

Check the CO/HC concentration during idling and when running at 2500 rpm.

HINT:

When doing the 2 mode (with the engine idling/running at 2500 rpm) test, the measuring procedures are determined by applicable local regulations.


If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.

i.

Check the heated oxygen sensor (for Sensor 1) operation.

Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>HEATED OXYGEN SENSOR(for Sensor 1)>INSPECTION


ii.

Check the heated oxygen sensor (for Sensor 2) operation.

Click hereEngine / Hybrid System>1NZ-FE ENGINE CONTROL>HEATED OXYGEN SENSOR(for Sensor 2)>INSPECTION


iii.

See the table below for possible causes, then inspect the applicable parts and repair them if necessary.

CO HC Problems Possible Causes
Normal High Rough idling
1.

Faulty ignition:

·

Incorrect timing

·

Fouled, shorted or improperly gapped plugs


2.

Incorrect valve clearance

3.

Leakage from intake and exhaust valves

4.

Leakage from cylinders


Low High Rough idling
(Fluctuating HC reading)
1.

Vacuum leaks:

·

PCV hoses

·

Intake manifold

·

Throttle body with motor assembly

·

Brake booster line


2.

Lean mixture causing misfire


High High Rough idling
(Black smoke from exhaust)
1.

Restricted air cleaner filter element sub-assembly

2.

Plugged PCV valve

3.

Faulty EFI systems:

·

Faulty fuel pressure regulator assembly

·

Faulty engine coolant temperature sensor

·

Faulty mass air flow meter

·

Faulty ECM

·

Faulty fuel injector assembly

·

Throttle body with motor assembly