Home › Engine / Hybrid System › 2NZ-FE ENGINE MECHANICAL › ENGINE ASSEMBLY(for Manual Transaxle) › 2014.03–2016.07
RM30M0E _51 Engine / Hybrid System _017074 2NZ-FE ENGINE MECHANICAL _0091018 ENGINE ASSEMBLY(for Manual Transaxle) A

2NZ-FE ENGINE MECHANICAL  ENGINE ASSEMBLY(for Manual Transaxle)  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with manual transaxle assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Fan Shroud Ventilation Duct)

Hide 3.DISCHARGE FUEL SYSTEM PRESSURE

Hide 4.REMOVE FRONT WHEELS

Hide 51442C 5.REMOVE ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

a.

Remove the 3 bolts, 5 screws and engine under cover LH from the vehicle.


Hide 51441C 6.REMOVE ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

a.

Remove the 2 bolts, 2 screws and engine under cover RH from the vehicle.


Hide 51451A 7.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

a.

Remove the 4 screws, 5 clips and center engine under cover from the vehicle.


Hide 51405A 8.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

a.

Remove the 11 bolts and No. 1 engine under cover sub-assembly from the vehicle.


Hide 11.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 11212 12.REMOVE NO. 2 CYLINDER HEAD COVER

Hide 23820 13.DISCONNECT FUEL VAPOR FEED HOSE ASSEMBLY

Hide 23827A 14.DISCONNECT NO. 2 FUEL VAPOR FEED HOSE

Hide 17735 15.REMOVE AIR CLEANER CAP WITH NO. 1 AIR CLEANER HOSE

Hide 17801 16.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.
A310643

Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


Hide 17.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A111178

Disengage the clamp to disconnect the engine wire from the air cleaner case sub-assembly.


b.

Remove the 3 bolts and air cleaner case sub-assembly from the air cleaner bracket.


Hide 23820 18.REMOVE FUEL VAPOR FEED HOSE ASSEMBLY

A106615

a.

Loosen the 2 hose clips and remove the fuel vapor feed hose assembly from the cylinder head cover sub-assembly and fuel tube.


Hide 28800 19.REMOVE BATTERY

a.

Remove the terminal cover from the positive (+) battery terminal.


b.
A111179C01
0.406,0.198 0.573,0.333 true 0.854,0.24 0.729,0.5 true 0.229,0.094 0.542,0.25 0.313,0.156 10 false *1 0.885,0.125 1.104,0.281 0.219,0.156 10 false *2
*1 Engine Room Main Wire
*2 Engine Wire


Remove the nut and disconnect the engine room main wire with engine wire from the positive (+) battery terminal.


c.

Disengage the 2 claws to disconnect the engine room main wire from the engine wire.


d.

Remove the 2 nuts, battery clamp bolt and battery clamp sub-assembly from the battery carrier assembly.


e.

Remove the battery from the battery tray.


Hide 74431 20.REMOVE BATTERY TRAY

a.
A310644

Remove the battery tray from the battery carrier assembly.


Hide 74410 21.REMOVE BATTERY CARRIER ASSEMBLY

A304753

a.

Disengage the 6 clamps to disconnect the engine wire from the battery carrier assembly.


b.

Remove the 5 bolts and battery carrier assembly from the engine mounting insulator LH and vehicle.


Hide 22.DISCONNECT RADIATOR RESERVOIR TANK HOSE

Hide 16573B 23.DISCONNECT NO. 3 RADIATOR HOSE

A111184

a.

Loosen the hose clip and disconnect the No. 3 radiator hose from the water filler sub-assembly.


Hide 16572D 24.DISCONNECT NO. 2 RADIATOR HOSE

A111512

a.

Loosen the hose clip and disconnect the No. 2 radiator hose from the water inlet.


Hide 87245 25.DISCONNECT INLET HEATER WATER HOSE

a.
A305927

Loosen the hose clip and disconnect the inlet heater water hose from the cylinder head sub-assembly.


Hide 87246 26.DISCONNECT OUTLET HEATER WATER HOSE

a.
A305930

Loosen the hose clip and disconnect the outlet heater water hose from the No. 1 water by-pass pipe.


Hide 23842A 27.REMOVE EFI FUEL PIPE CLAMP

Hide 23901 28.DISCONNECT FUEL TUBE SUB-ASSEMBLY

Hide 44772 29.DISCONNECT CHECK VALVE TO CONNECTOR TUBE HOSE

A111514

a.

Loosen the hose clip and disconnect the check valve to connector tube hose from the booster vacuum tube.


Hide 16361A 30.REMOVE FAN AND GENERATOR V BELT

Hide 31470 31.SEPARATE CLUTCH RELEASE CYLINDER ASSEMBLY

Hide 88320 32.SEPARATE COOLER COMPRESSOR ASSEMBLY (w/o Fan Shroud Ventilation Duct)

A111513

a.

Disconnect the cooler compressor assembly connector.


b.

Remove the 3 bolts to separate the cooler compressor assembly from the oil pan sub-assembly.

HINT:

Separate the cooler compressor assembly together with the No. 1 cooler refrigerant discharge hose and No. 1 cooler refrigerant suction hose, then suspend them from the vehicle with a piece of rope.



Hide 88711 33.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (w/ Fan Shroud Ventilation Duct)

Hide 88712 34.DISCONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE (w/ Fan Shroud Ventilation Duct)

Hide 88320 35.REMOVE COOLER COMPRESSOR ASSEMBLY (w/ Fan Shroud Ventilation Duct)

Hide 55550 36.REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY

Hide 82121 37.DISCONNECT ENGINE WIRE

a.

Remove the relay block cover from the engine room relay block.


b.
A111519

Disengage the clamp to disconnect the engine wire from the vehicle.


c.

Disconnect the connector from the engine room relay block.


d.

Remove the nut from the engine room relay block.


e.

Disengage the 2 claws to disconnect the engine wire from the engine room relay block.


f.
A304754

Disconnect the 3 connectors as shown in the illustration.


g.

Disengage the 2 clamps to disconnect the engine wire from the wire harness clamp bracket and vehicle.


h.
A304743

Disengage the clamp to disconnect the engine wire from the wire harness clamp bracket.


i.

Disengage the grommet and pass the engine wire through the hole to the inside of the engine room.


j.
A111518

Disengage the 2 clamps to disconnect the engine wire from the engine mounting bracket LH.


k.

Remove the bolt to disconnect the engine wire from the manual transaxle assembly.


Hide 58910C 38.REMOVE REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58910C 39.REMOVE REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)

Hide 57533B 40.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 41.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 33820B 42.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 43420 43.REMOVE FRONT DRIVE SHAFT ASSEMBLY

Hide 45259A 44.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45209 45.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45025D 46.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 47.REMOVE ENGINE ASSEMBLY WITH MANUAL TRANSAXLE ASSEMBLY

a.
A112925

Loosen the engine moving control rod bolt.


b.
A112927C01
0,0 0.01,0 false
V100155

Attachment Placement Position


Place the height adjustment attachments or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the engine assembly with manual transaxle assembly and front suspension crossmember sub-assembly.

NOTICE:
·

Place the height adjustment attachments or plate lift attachments so that the engine assembly with manual transaxle assembly is level.

·

Do not perform any procedure while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

As the engine assembly with manual transaxle assembly is very heavy, be sure to support it securely.

·

To prevent deformation of the No. 2 oil pan sub-assembly, never set any attachments against the No. 2 oil pan sub-assembly of the engine assembly.




c.
A113659

Remove the bolt and 2 nuts to disconnect the engine mounting insulator sub-assembly RH from the engine mounting bracket RH.


d.
A113661

Remove the through bolt and nut to disconnect the engine mounting insulator LH from the engine mounting bracket LH.

HINT:

Loosen by holding the nut and turning the through bolt.



e.
A116978

Remove the 6 bolts, engine assembly with manual transaxle assembly and front suspension crossmember sub-assembly from the vehicle.

NOTICE:

When removing the engine assembly with manual transaxle assembly and front suspension crossmember sub-assembly, be careful not to damage any engine wire or the steering shaft.



Hide 12281A 48.INSTALL NO. 1 ENGINE HANGER

a.

Separate the air fuel ratio sensor wire from the wire harness clamp bracket.


b.
A310645

Remove the bolt and wire harness clamp bracket from the cylinder head sub-assembly.


c.
A105871C01
0.927,0.542 1.104,0.375 false 2.896,0.542 3.083,0.375 false 1.167,0.26 1.479,0.417 0.313,0.156 10 false *1 0.052,0.052 0.365,0.208 0.313,0.156 10 false *a 1.906,0.063 2.219,0.219 0.313,0.156 10 false *b 3.115,0.281 3.323,0.438 0.208,0.156 10 false *1
*1 No. 1 Engine Hanger
*a Front Side
*b Rear Side


Install the 2 No. 1 engine hangers to the cylinder head sub-assembly with the 2 bolts.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

HINT:
Part Name Part No.
No. 1 Engine Hanger 12281-0M020
Bolt 90119-T0011



Hide 51201 49.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

A304742

a.

Using an engine sling device and a chain block, suspend the engine assembly with manual transaxle assembly.


b.

Remove the through bolt and front suspension crossmember sub-assembly from the engine moving control rod bracket.


Hide 50.FIX MANUAL TRANSAXLE ASSEMBLY

a.

Attach the sling device to the engine hangers and chain block.

NOTICE:

Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.



b.
A116981C01
0,2.177 0.01,2.177 false
V100155

Attachment Placement Position


To enable removal of the engine assembly, adjust the positions of the height adjustment attachments or plate lift attachments and set them in place.

NOTICE:
·

Place the height adjustment attachments or plate lift attachments so that the engine assembly with manual transaxle assembly is level.

·

As the engine assembly with manual transaxle assembly is very heavy, be sure to support it securely.




c.
A116982

Use a lashing belt or a rope to secure the manual transaxle assembly to the engine lifter.

NOTICE:

Do not tighten the lashing belt or the rope any more than is necessary.



Hide 12321B 51.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

Hide 11363A 52.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 28100 53.REMOVE STARTER ASSEMBLY

Hide 33524B 54.REMOVE CONTROL CABLE BRACKET

a.
A302815

Remove the 2 bolts and control cable bracket from the manual transaxle assembly.


Hide 55.REMOVE ENGINE ASSEMBLY

a.
C261396E02
2.5,0.042 2.656,0.24 0.156,0.198 10 false A 0.917,0.083 1.073,0.281 0.156,0.198 10 false A 0.719,0.708 0.844,0.875 0.125,0.167 10 true B 1.021,1.719 1.146,1.885 0.125,0.167 10 true B 1.479,1.958 1.604,2.115 0.125,0.156 10 false B 2.146,1.969 2.271,2.125 0.125,0.156 10 false B 2.635,1.802 2.76,1.958 0.125,0.156 10 false B

Remove the 7 bolts and engine assembly from the manual transaxle assembly.

HINT:
·

Bolt A: Remove from manual transaxle assembly side

·

Bolt B: Remove from engine assembly side




Hide 31210 56.REMOVE CLUTCH COVER ASSEMBLY

Hide 31250B 57.REMOVE CLUTCH DISC ASSEMBLY

Hide 13405 58.REMOVE FLYWHEEL SUB-ASSEMBLY

a.

Using height adjustment attachments or plate lift attachments, place the engine assembly on a flat, level surface.

NOTICE:
·

Using height adjustment attachments or plate lift attachments, place the engine assembly horizontally.

·

To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.

·

Using an engine sling device and engine lift, secure the engine assembly before servicing.




b.
A166739E01
2.63,1.619 2.935,1.773 0.304,0.155 10 SST 1.954,2.054 2.592,1.726 false

Using SST, hold the crankshaft damper sub-assembly.

SST
09960-10010  (09962-01000, 09963-01000)


c.
A249640

Remove the 6 bolts and flywheel sub-assembly from the crankshaft.


Hide 59.INSTALL ENGINE STAND

a.

Using a sling device and a chain block, install the engine stand to the engine assembly.

NOTICE:
·

Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.

·

Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.




Hide 82121 60.REMOVE ENGINE WIRE

A121490

a.

Remove the 2 bolts to disconnect the engine wire from the cylinder head sub-assembly.


b.

Disconnect all the engine wire and connectors. Make sure that no engine wire are connected to the engine assembly.


Hide 12261 61.REMOVE VENTILATION HOSE

A259822

a.

Loosen the 2 hose clips and remove the ventilation hose from the cylinder head cover sub-assembly and intake manifold.


Hide 16502 62.REMOVE WATER FILLER SUB-ASSEMBLY

A116983

a.

Loosen the hose clip and disconnect the No. 1 radiator hose from the cylinder head sub-assembly.


b.

Remove the 2 nuts and water filler sub-assembly from the throttle body with motor assembly.


Hide 15301 63.REMOVE OIL LEVEL DIPSTICK SUB-ASSEMBLY

Hide 17111 64.REMOVE INTAKE MANIFOLD WITH THROTTLE BODY WITH MOTOR ASSEMBLY

A117312

a.

Loosen the hose clip and disconnect the union to connector tube hose from the booster vacuum tube.


b.
A117313

Loosen the hose clip and disconnect the water by-pass hose from the cylinder head sub-assembly.


c.
A116984

Loosen the hose clip and disconnect the No. 2 water by-pass hose from the No. 1 water by-pass pipe.


d.
A302829

Remove the 3 bolts, 2 nuts and intake manifold with throttle body with motor assembly from the cylinder head sub-assembly.


e.

Remove the intake manifold to head gasket from the intake manifold.


Hide 17167 65.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 25591 66.REMOVE MANIFOLD SUPPORT BRACKET

Hide 12305 69.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Only perform this procedure when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A121467

Remove the 3 bolts and engine mounting insulator sub-assembly RH from the vehicle.


Hide 12372A 70.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Only perform this procedure when replacement of the engine mounting insulator LH is necessary.


a.
A121469

Remove the 5 bolts and engine mounting insulator LH from the vehicle.