Home › Drivetrain › K411 CVT › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY › 2016.07–2017.10
RM30M0E _52 Drivetrain _052750 K411 CVT _0259915 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY A

K411 CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 4.REMOVE FRONT WHEELS

Hide 51442C 5.REMOVE ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

Hide 51441C 6.REMOVE ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51451A 7.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 51405A 8.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 10.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 17880 11.REMOVE AIR CLEANER HOSE ASSEMBLY

Hide 17801 13.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 14.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 58910C 18.REMOVE REAR CONSOLE BOX ASSEMBLY (w/ Console Box Lid)

Hide 58910C 19.REMOVE REAR CONSOLE BOX ASSEMBLY (w/o Console Box Lid)

Hide 33820B 20.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 45259A 22.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 23.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 24.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 57533B 25.REMOVE FRONT FLOOR CENTER BRACE (for Sedan)

Hide 57533B 26.REMOVE FRONT FLOOR CENTER BRACE (for Hatchback)

Hide 17410 27.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for Sedan)

Hide 17410 28.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for Hatchback)

Hide 43498A 29.REMOVE NO. 1 DRIVE SHAFT HEAT INSULATOR

Hide 30.REMOVE FRONT DRIVE SHAFT ASSEMBLIES

Hide 28100 31.REMOVE STARTER ASSEMBLY

Hide 11363A 32.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 35141F 33.SEPARATE NO. 1 BREATHER PLUG

a.
A304776

Disengage the clamp and separate the No. 1 breather plug from the hose clamp.


Hide 16260 34.DISCONNECT WATER BY-PASS HOSE ASSEMBLY

a.
C354296

Slide the 2 hose clips and disconnect the 2 water by-pass hoses from the transmission oil cooler.


b.

Disengage the 2 clamps to separate the water by-pass hose assembly from the continuously variable transaxle assembly.


Hide 82121 35.DISCONNECT ENGINE WIRE

a.
C288087

Disconnect the 6 connectors from the continuously variable transaxle assembly.


b.

Disengage the 8 clamps to separate the engine wire from the continuously variable transaxle assembly.


c.

Remove the bolt to separate the engine wire from the continuously variable transaxle assembly.


d.
C264909

Remove the bolt and wire harness clamp bracket from the continuously variable transaxle assembly.


Hide 32101A 36.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
A305670N01
0.635,1.833 0.958,1.708 false 0.344,1.75 0.802,1.948 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley.

SST
09960-10010  (09962-01000, 09963-01000)


b.
C236683

Remove the 6 drive plate and torque converter assembly setting bolts.


Hide 37.SUPPORT ENGINE ASSEMBLY

a.
C288088C01
1.448,1.188 1.083,0.708 1.083,0.708 1.792,1.26 true 0.708,2.219 0.854,2.094 false 0.896,0.604 1.063,0.802 0.167,0.198 10 true *a 0.552,2.135 0.865,2.292 0.313,0.156 10 false *b
*a Attachment
*b Engine Lifter
V100155

Attachment Placement Positions


Place the height adjustment attachments or plate lift attachments in the positions shown in the illustration and set the engine lifter underneath the engine assembly.

NOTICE:
·

Place the height adjustment attachments or plate lift attachments so that the engine assembly with the continuously variable transaxle assembly is level.

·

As the engine assembly with the continuously variable transaxle assembly is very heavy, be sure to support it securely.

·

To prevent deformation of the oil pan sub-assembly, never set any attachments against the oil pan sub-assembly of the engine assembly.

·

To prevent deformation of the transaxle oil pan sub-assembly, never set any attachments against the transaxle oil pan sub-assembly.




Hide 51201 38.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 12364B 39.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

C219025

a.

Remove the 3 bolts and No. 2 engine moving control rod from the continuously variable transaxle assembly.


Hide 30400 40.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C288089C01
2.094,2.094 2.271,1.99 false 1.75,0.323 2.052,0.573 true 1.948,2.01 2.26,2.167 0.313,0.156 10 false *a 1.594,0.219 1.76,0.385 0.167,0.167 10 false *b
*a Transmission Jack
*b Lashing Belt
V100155

Attachment Placement Positions


Set the attachments in the positions shown in the illustration and set the transmission jack underneath the continuously variable transaxle assembly.

NOTICE:
·

To prevent deformation of the transaxle oil pan sub-assembly, never set any attachments against the transaxle oil pan sub-assembly.

·

Secure the continuously variable transaxle assembly to the transmission jack with a lashing belt, etc., to prevent the continuously variable transaxle assembly from falling.




b.
C288090

Remove the bolt and nut, and separate the engine mounting bracket LH from the engine mounting insulator LH.

HINT:

Turn the bolt while holding the nut.



c.
C288091

Remove the 5 bolts and engine mounting insulator LH from the body.


d.
C231550

Remove the 4 bolts and engine mounting bracket LH from the continuously variable transaxle assembly.


e.
C231548N02
1.396,0.375 1.552,0.573 0.156,0.198 10 false A 2.667,0.531 2.823,0.729 0.156,0.198 10 false A 2.99,1.26 3.146,1.458 0.156,0.198 10 false A 3.052,1.854 3.208,2.052 0.156,0.198 10 true A 2.729,2.427 2.885,2.625 0.156,0.198 10 false B 2.385,2.708 2.542,2.906 0.156,0.198 10 false B 1.75,2.813 1.906,3.01 0.156,0.198 10 false B 1.208,2.677 1.365,2.875 0.156,0.198 10 true B

Remove the 8 bolts and continuously variable transaxle assembly from the engine assembly.

NOTICE:
·

Make sure that the engine assembly is not tilted.

·

To prevent damage to the knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.

·

Do not allow the torque converter assembly to fall off.



HINT:
·

Bolt A: Remove from continuously variable transaxle assembly side

·

Bolt B: Remove from engine assembly side




Hide 32000A 41.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C231549

Remove the torque converter assembly from the continuously variable transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 30400E 42.REMOVE CVT OIL PUMP TYPE T OIL SEAL

NOTICE:
·

Do not remove the front oil pump assembly from the CVT main body, as there is the possibility of the entry of dust and foreign matter.

·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which may prevent the vehicle from being driven, may occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, paper towels, etc. that may produce lint, dust or foreign matter.

·

Perform the operation as quickly as possible, as dust and foreign matter may enter the CVT while the torque converter assembly is not attached to it.

·

Do not use an air gun until the torque converter assembly has been installed, as it may cause dust and foreign matter to be stirred up.



a.
C208788N09
2.406,2.063 2.406,2.688 false 2.281,2.688 2.635,2.896 0.354,0.208 10 false SST

Clean the tips of both the claws of SST and the center bolt.


b.

Using SST, remove the CVT oil pump type T oil seal from the continuously variable transaxle assembly.

SST
09308-10010  

NOTICE:

Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles may be produced if they do.



Hide 33823 43.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C288092

Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.


Hide 44.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C264993

Disengage the breather hose clamp and separate the breather plug hose from the wire harness clamp bracket.


b.

Remove the 5 bolts and 4 wire harness clamp brackets from the continuously variable transaxle assembly.

C288094


Hide 35141D 45.REMOVE BREATHER PLUG HOSE

HINT:

Perform this procedure only when replacement of the breather plug hose is necessary.


a.
C288093C02
0.417,1.844 1.677,1.844 true 0.427,1.021 0.917,1.021 false 0.417,0.271 0.708,0.271 false 0.25,0.177 0.563,0.333 0.313,0.156 10 false *1 0.25,0.938 0.563,1.094 0.313,0.156 10 false *2 0.25,1.76 0.563,1.917 0.313,0.156 10 false *3
*1 No. 1 Breather Plug
*2 Breather Plug Hose
*3 Breather Hose Clamp


Disengage the clamp and remove the breather hose clamp from the breather plug hose.


b.

Remove the breather plug hose with the No. 1 breather plug from the continuously variable transaxle assembly.


c.

Remove the No. 1 breather plug from the breather plug hose.


Hide 32000A 46.INSPECT TORQUE CONVERTER ASSEMBLY