Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY › from 2018.01
RM30M0E _52 Drivetrain _052969 K312 CVT _0259988 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY A

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 4.REMOVE FRONT WHEELS

Hide 51442C 5.REMOVE ENGINE UNDER COVER LH (w/o Metal Type Under Cover)

Hide 51441C 6.REMOVE ENGINE UNDER COVER RH (w/o Metal Type Under Cover)

Hide 51451A 7.REMOVE CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 51405A 8.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 10.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 17880 11.REMOVE AIR CLEANER HOSE ASSEMBLY

Hide 17801 13.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 14.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 58910C 18.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 58817A 20.REMOVE NO. 2 FRONT CONSOLE BOX INSERT

Hide 58911A 21.REMOVE NO. 1 BOX SIDE PANEL

Hide 58912C 22.REMOVE NO. 2 BOX SIDE PANEL

Hide 58839A 24.REMOVE CONSOLE BOX HOLE COVER

Hide 58810J 25.REMOVE CONSOLE BOX ASSEMBLY

Hide 33820B 26.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 82121 27.DISCONNECT ENGINE WIRE

a.
C375297C02
0.854,3.958 1.167,4.115 0.313,0.156 10 false *1 1.219,3.354 1.406,3.542 0.188,0.188 10 true *2 2.615,3.438 2.813,3.615 0.198,0.177 10 true *3 2.583,1.229 2.792,1.417 0.208,0.188 10 true *4
*1 Heated Oxygen Sensor Connector
*2 Transmission Wire Connector
*3 Transmission Revolution Sensor (NIN) Connector
*4 Park/Neutral Position Switch Connector


Disconnect the heated oxygen sensor connector.


b.

Disconnect the transmission wire connector.


c.

Disconnect the transmission revolution sensor (NIN) connector.


d.

Disconnect the park/neutral position switch connector.


e.

Remove the bolt to disconnect the engine wire from the continuously variable transaxle assembly.


f.

Disengage the 4 clamps to disconnect the engine wire from the continuously variable transaxle assembly.


g.
C349375C01
1.5,3.458 1.813,3.656 0.313,0.198 10 true *1 1.385,4.135 1.604,4.365 0.219,0.229 10 true *2
*1 Transmission Revolution Sensor (NOUT) Connector
*2 Oil Pressure Sensor Connector


Disconnect the transmission revolution sensor (NOUT) connector.


h.

Disconnect the oil pressure sensor connector.


i.

Disengage the 4 clamps to disconnect the engine wire from the continuously variable transaxle assembly.


Hide 16260 28.DISCONNECT WATER BY-PASS HOSE ASSEMBLY

a.
C354295

Slide the 2 hose clips and disconnect the 2 water by-pass hoses from the transmission oil cooler.


b.

Disengage the 2 clamps to separate the water by-pass hose assembly from the continuously variable transaxle assembly.


Hide 33823 29.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C349376

Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.


Hide 45259A 31.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45209 32.SEPARATE STEERING SLIDING YOKE SUB-ASSEMBLY

Hide 45025D 33.REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 57533B 34.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 35.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 43498A 36.REMOVE NO. 1 DRIVE SHAFT HEAT INSULATOR

Hide 38.SUPPORT ENGINE ASSEMBLY

a.
C354279C01
0,0 0,0 false
V100155

Attachment Placement Position


Place height adjustment attachments or plate lift attachments in the position shown in the illustration and set an engine lifter underneath the engine assembly.

NOTICE:

Using height adjustment attachments and plate lift attachments, keep the engine assembly horizontal.



Hide 51201 39.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 12364B 40.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C354280

Remove the 4 bolts and No. 2 engine moving control rod from the continuously variable transaxle assembly.


Hide 30400 41.SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C354278C01
0.969,1.615 1.802,1.042 true 0.865,1.594 1.177,1.792 0.313,0.198 10 false *a
*a Lashing Belt


Using a transmission jack, support the continuously variable transaxle assembly.

NOTICE:
·

Adjust the attachment of the transmission jack to securely fix the continuously variable transaxle assembly to the transmission jack.

·

To prevent the transaxle oil (CVT) pan sub-assembly from deforming, do not place any attachments under the transaxle oil (CVT) pan sub-assembly of the continuously variable transaxle assembly.

·

Using a lashing belt or a rope, fix the continuously variable transaxle assembly to the transmission jack.




Hide 28100 42.REMOVE STARTER ASSEMBLY

Hide 11363A 43.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 32101G 44.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C349377N01
2.083,1.615 1.865,1.333 true 2.146,1.542 2.479,1.708 0.333,0.167 10 true SST

Using SST, hold the crankshaft pulley.

SST
09960-10010  (09962-01000, 09963-01000)


b.
C349378

Remove the 6 drive plate and torque converter assembly setting bolts.


Hide 12372A 45.REMOVE ENGINE MOUNTING INSULATOR LH

a.
C354275

Remove the bolt and nut to separate the engine mounting insulator LH from the engine mounting bracket LH.


b.
C354276

Remove the 5 bolts.


c.

Disengage the hook to remove the engine mounting insulator LH from the vehicle body.


Hide 12325A 46.REMOVE ENGINE MOUNTING BRACKET LH

a.
C354277

Remove the 3 bolts and engine mounting bracket LH from the continuously variable transaxle assembly.


Hide 30400 47.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C349368N01
1.49,0.083 1.646,0.281 0.156,0.198 10 false A 2.271,0.188 2.427,0.385 0.156,0.198 10 false A 2.573,0.792 2.729,0.99 0.156,0.198 10 false A 2.594,1.323 2.75,1.521 0.156,0.198 10 false A 2.354,1.688 2.51,1.885 0.156,0.198 10 true B 2.073,1.875 2.229,2.073 0.156,0.198 10 true B 1.625,1.938 1.781,2.135 0.156,0.198 10 true B 1.208,1.76 1.365,1.958 0.156,0.198 10 true B

Remove the 8 bolts and continuously variable transaxle assembly from the engine assembly.

NOTICE:

To prevent damage to the knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.


HINT:
·

Bolt (A): Remove from continuously variable transaxle assembly side.

·

Bolt (B): Remove from engine assembly side.




Hide 32000A 48.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C349369

Remove the torque converter assembly from the continuously variable transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 30400E 49.REMOVE CVT OIL PUMP TYPE T OIL SEAL

NOTICE:
·

Do not remove the front oil pump assembly from the CVT main body, as there is a possibility of the entry of dust and foreign matter.

·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a CVT malfunction, which could prevent the vehicle from being able to be driven, could occur if dust or fine foreign matter enters the CVT.

·

Do not use cotton work gloves, cloths, or paper towels, etc. that may produce lint, dust or foreign matter.

·

Perform the operation as quickly as possible, as dust and foreign matter could enter the CVT while the torque converter assembly is removed.

·

Do not use an air gun until the torque converter assembly has been installed, as it could cause dust and foreign matter to be stirred up.



a.

Clean the tips of both the claws of SST and the center bolt.

SST
09308-10010  


b.
C329642N01
1.552,2.635 1.552,2.24 false 1.448,2.677 1.906,2.875 0.458,0.198 10 false SST

Using SST, remove the CVT oil pump type T oil seal.

NOTICE:

Pay attention to the angle of the claws when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles could be produced if they do.



Hide 50.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C349379

Remove the 5 bolts and 5 wire harness clamp brackets from the continuously variable transaxle assembly.


Hide 35123B 51.REMOVE TRANSMISSION BREATHER SKIRT

a.
C354264

Separate the No. 1 breather plug (CVT) from the clamp.


b.
C354265

Remove the clamp from the transmission breather skirt.


c.
C354266

Remove the bolt and transmission breather skirt from the continuously variable transaxle assembly.


Hide 52.REMOVE STRAIGHT SCREW PLUG

a.
C354282

Remove the straight screw plug and gasket from the continuously variable transaxle assembly.


Hide 35141D 53.REMOVE BREATHER PLUG HOSE

HINT:

Perform this procedure only when replacement of the breather plug hose is necessary.


a.
C267511

Remove the breather plug hose from the continuously variable transaxle assembly.


b.
C333415C01
0.823,0.969 0.823,0.635 false 2.615,1.115 2.948,1.115 false 1.688,1.51 1.688,1.177 false 2.646,1.667 2.979,1.667 false 0.76,0.99 1.073,1.146 0.313,0.156 10 false *1 1.635,1.542 1.948,1.698 0.313,0.156 10 false *2 3,1.052 3.313,1.208 0.313,0.156 10 false *3 3.021,1.604 3.333,1.76 0.313,0.156 10 false *4
*1 No. 1 Breather Plug (CVT)
*2 Breather Plug Hose
*3 No. 2 Breather Plug (CVT)
*4 O-ring


Remove the No. 1 breather plug (CVT) and No. 2 breather plug (CVT) from the breather plug hose.


c.

Remove the O-ring from the No. 2 breather plug (CVT).


Hide 32000A 54.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 32101B 55.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY