Home › Engine / Hybrid System › M15A-FXE (ENGINE CONTROL) › SFI SYSTEM
RM36W0E _51 Engine / Hybrid System _087500 M15A-FXE ENGINE CONTROL _0418535 SFI SYSTEM C

M15A-FXE ENGINE CONTROL  SFI SYSTEM  P319000  Poor Engine Power  P319100  Engine does not Start  


DESCRIPTION

The ECM receives signals from the hybrid vehicle control ECU assembly such as the requested engine torque, target engine speed and engine cranking status, and controls the engine output based on the target engine speed and requested torque.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P319000 Poor Engine Power When all of the following conditions are met (1 trip detection logic):
·

The engine speed is 650 rpm or more (varies depending on the engine coolant temperature).

·

Engine torque requested by the hybrid vehicle control ECU exceeds a certain value.

·

The hybrid vehicle control ECU assembly judges that the engine has started.

·

The fuel tank is not empty.

·

Communication between the hybrid vehicle control ECU assembly and ECM is normal.

·

The actual engine torque is less than 20% of the requested engine torque for 6 seconds, or until the crankshaft rotates 100 times (whichever takes longer, differs depending on the engine coolant temperature).


·

Intake system

·

Throttle with motor body assembly

·

Fuel system

·

Engine assembly

·

Mass air flow meter

·

Out of fuel

·

Engine coolant temperature sensor

·

Crankshaft position sensor

·

Camshaft position sensor

·

EGR valve assembly

·

Fuel pump control circuit

·

PCV valve and hose

·

PCV hose connections

·

ECM


Comes on DTC stored SAE Code: P3190
P319100 Engine does not Start When all of the following conditions are met (1 trip detection logic):
·

The engine speed is 650 rpm or more (varies depending on the engine coolant temperature).

·

The fuel tank is not empty.

·

Communication between the hybrid vehicle control ECU assembly and ECM is normal.

·

After the hybrid vehicle control ECU assembly sends the engine start request signal, it does not detect engine start (generation of engine torque) for 6 seconds, or until the crankshaft rotates 100 times (whichever takes longer, differs depending on the engine coolant temperature).


·

Intake system

·

Throttle with motor body assembly

·

Fuel system

·

Engine assembly

·

Mass air flow meter

·

Out of fuel

·

Engine coolant temperature sensor

·

Crankshaft position sensor

·

Camshaft position sensor

·

EGR valve assembly

·

Fuel pump control circuit

·

PCV valve and hose

·

PCV hose connections

·

ECM


Comes on DTC stored SAE Code: P3191

MONITOR DESCRIPTION

1.

The ECM receives signals such as requested engine torque, target engine speed and engine cranking status from the hybrid vehicle control ECU assembly.

2.

The ECM controls engine start and stop and the throttle valve angle based on the signals received from the hybrid vehicle control ECU assembly.

3.

The ECM receives the actual engine torque calculated by the hybrid vehicle control ECU assembly based on the generator torque.

4.

When the actual engine torque is less than 20% of the requested engine torque*, the ECM judges that the engine output is abnormal and stores DTC P319000.

(The engine may not have started in the above situation.)

*: Requested torque = Requested Engine Torque (kW) / HV Target Engine Speed (rpm) x 9549


5.

If the ECM does not detect engine start torque (actual engine torque) even though it has received an engine start request and started the engine, it stores DTC P319100.

HINT:
·

When DTCs P319000, P319100 and P319300 are output, the engine may be stopped due to the engine condition.

At this time, after adding fuel or performing repairs, clear the DTCs. Then turn the ignition switch off to return to the normal condition.

·

When this DTC is output and the engine is stopped, the HV battery cannot be charged since the vehicle is driven with the motor only. If the vehicle continues to be driven under this condition, the HV battery will become depleted and the ignition switch will not be able to be turned to ON (READY).

·

When DTC P319000 or P319100 is stored, the engine torque has dropped by 80% or the engine cannot be started. If any DTCs that indicate malfunctioning of engine related parts are stored at the same time, repair the malfunctioning parts first.

·

If engine knock is detected due to mechanical noise or a knock sensor being loose, the ignition timing (Knock F/B Value, Knock Correct Learn Value) may be excessively retarded and DTC P319000 may be stored.

Relevant Data List Items:

ECM (Powertrain / Engine / Data List)
HV Target Engine Speed Engine Speed Requested Engine Torque Actual Engine Torque
Throttle Position Command Throttle Position Sensor No.1 Voltage Calculate Load Coolant Temperature
Short FT B1S1 Long FT B1S1 Target EGR Valve Position No.1 Ignition Timing Cylinder #1
Knock F/B Value Knock Correct Learn Value - -

Hybrid Vehicle Control ECU (Powertrain / Hybrid Control / Data List)
Target Engine Revolution Engine Speed Target Engine Power Coolant Temperature
Engine Idling Request - - -




MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

NOTICE:

If the MIL or a master warning light illuminates, immediately end the confirmation driving pattern. If DTCs P319000, P319100 and P319300 are output and the engine is stopped, the HV battery will no longer be chargeable and the distance that the vehicle can be driven will be limited.


A299140E51
0.594,2.198 1.74,2.75 1.146,0.552 10 false Ignition Switch ON (READY) 0.667,0.927 1.719,1.375 1.052,0.448 10 false 40 km/h [Engine running] 3.063,2.854 4.865,3.354 1.802,0.5 10 false Total engine operation time of 10 minutes or more 2.229,2.094 2.688,2.292 0.458,0.198 10 false [A] 5.115,3.208 5.573,3.406 0.458,0.198 10 false [C] 3.458,0.51 3.917,0.708 0.458,0.198 10 false [B]

1.

Apply the parking brake firmly.

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON.

4.

Turn the GTS on.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Turn the ignition switch to ON (READY).

8.

Turn the GTS on.

9.

Fully depress the accelerator pedal for 10 seconds with the vehicle stopped, the shift lever in P and the brake pedal depressed [A].

NOTICE:

As soon as the engine starts, release the accelerator pedal.


10.

Release the parking brake.

11.

Drive the vehicle at an average of approximately 40 km/h (25 mph) or more until the total engine operation time is 10 minutes or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

It is not necessary to maintain the vehicle speed at 40 km/h (25 mph) throughout the road test.

·

If the engine stops, further depress the accelerator pedal to restart the engine.



12.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

15.

Input the DTC: P319000 or P319100.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system is malfunctioning.

·

If the judgment result shows INCOMPLETE, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>VEHICLE CONTROL HISTORY



HINT:
·

Performing this diagnosis procedure repeatedly for symptom confirmation may cause the SOC to drop, preventing the system from entering the READY-on state. In this case, use the THS charger to charge the HV battery.

·

Cranking the engine once causes the SOC to drop by approximately 1%.

·

Charging the HV battery once (10 minutes) using the THS charger restores the SOC approximately 2%.

·

Charging the HV battery using the THS charger takes approximately 10 minutes when the HV battery temperature is 25°C (77°F) or approximately 30 minutes when the HV battery temperature is 0°C (32°F).

·

The THS charger is a supplemental charging device that charges the HV battery enough to enable the engine to start (the vehicle can enter the READY-on state).

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P319000, P319100 AND/OR P319300)
a.

Check for DTCs and freeze frame data and write them down.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
P319000, P319100 or P319300 and other DTCs are output A
P319000 or P319100 are output B
P319300 is output C


HINT:

If any SFI system DTCs other than DTC P319000, P319100 or P319300 are output, perform troubleshooting for those DTCs first.




A

GO TO DTC CHART

B

2.CHECK SHORTAGE OF FUEL

C

2.CHECK SHORTAGE OF FUEL
a.

Check the amount of fuel remaining.

OK:

There is enough fuel.


HINT:
·

DTCs P319000, P319100 and/or P319300 may be output if the vehicle ran out of fuel in the past.

·

If not enough fuel is added, DTC P319000, P319100 or P319300 may be output again. If the engine cannot be started because the vehicle is out of fuel, add fuel until the fuel level warning turns off.




Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REFILL FUEL

3.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK PCV VALVE AND HOSE CONNECTIONS
4.CHECK PCV VALVE AND HOSE CONNECTIONS
A457192

a.

Check the PCV hose connections.


b.

Check the PCV valve.

Click hereEngine / Hybrid System>M15A-FXE (EMISSION CONTROL)>PCV VALVE>INSPECTION

OK:

PCV hose and PCV valve are connected correctly and are not damaged.



Result:
Proceed to
OK
NG



OK

5.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE PCV VALVE OR HOSE

5.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>M15A-FXE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from the intake system.



Result:
Proceed to
OK
NG



OK

6.CHECK FOR UNUSUAL NOISE OR VIBRATION WHEN STARTING ENGINE OR REVVING

NG

REPAIR OR REPLACE INTAKE SYSTEM
HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



6.CHECK FOR UNUSUAL NOISE OR VIBRATION WHEN STARTING ENGINE OR REVVING
OK:

Unusual noise and vibration do not occur.


Result:
Proceed to
OK
NG



OK

7.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS

7.CHECK FUEL PRESSURE

OK

8.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY

NG

25.CHECK FUEL LINE
8.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY

OK

9.INSPECT MASS AIR FLOW METER

NG

REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>THROTTLE BODY>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the throttle body with motor assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



9.INSPECT MASS AIR FLOW METER
a.

Inspect the mass air flow meter, referring to On-vehicle Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>ON-VEHICLE INSPECTION


b.

Inspect the mass air flow meter, referring to Inspection for Mass Air Flow Meter.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION


Result:
Proceed to
OK
NG



OK

10.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

NG

REPLACE MASS AIR FLOW METER

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the mass air flow meter.



10.INSPECT ENGINE COOLANT TEMPERATURE SENSOR

OK

11.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

NG

REPLACE ENGINE COOLANT TEMPERATURE SENSOR

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>ENGINE COOLANT TEMPERATURE SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



11.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)

Pre-procedure1

a.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

b.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.

HINT:

The A/C switch and all accessories should be off.



Procedure1

c.

Confirm that the value of Data List item Engine Independent is "Operate" and then check the value of Intake Manifold Absolute Pressure while performing the Active Test.

Powertrain > Engine > Active Test
Active Test Display
Control the EGR Step Position
Data List Display
Intake Manifold Absolute Pressure
Coolant Temperature
EGR Step Position
Engine Independent
50004 372 25 385,205,386,428
NOTICE:
·

Make sure that the value of Data List item Engine Independent is "Operate" while performing the Active Test.

·

Do not leave the EGR valve open for 10 seconds or more during the Active Test.

·

Be sure to return the EGR valve to step 0 when the Active Test is completed.

·

Do not open the EGR valve 30 steps or more during the Active Test.



OK:

The value of Intake Manifold Absolute Pressure changes in response to the EGR step position when the value of Engine Independent is "Operate".


Standard:
- Control the EGR Step Position (Active Test)
0 Steps 0 to 30 Steps
Intake Manifold Absolute Pressure
(Data List)
(EGR valve is fully closed) Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed


HINT:
·

If the value of Data List item Engine Independent is "Not Opr" when the engine is idling, charge control is being performed. Perform the Active Test after charge control is complete ("Operate" is displayed).

·

While performing the Active Test, if the increase in the value of Intake Manifold Absolute Pressure is small, the EGR valve assembly may be malfunctioning.

·

Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of Intake Manifold Absolute Pressure may occur while performing the Active Test. However, the amount that the value of Intake Manifold Absolute Pressure increases will be smaller than normal.

·

If the Active Test cannot be performed due to a malfunction such as the engine not starting, perform the EGR valve assembly inspection the following step.




Post-procedure1

d.

None.


Result:
Proceed to
OK
NG



OK

13.REPLACE CRANKSHAFT POSITION SENSOR

NG

12.INSPECT EGR VALVE ASSEMBLY
12.INSPECT EGR VALVE ASSEMBLY

Pre-procedure1

a.

Remove the EGR valve assembly.

HINT:

Click hereEngine / Hybrid System>M15A-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL



Procedure1

b.

Check if the EGR valve is stuck open.

OK:

EGR valve is tightly closed.



Post-procedure1

c.

None.


Result:
Proceed to
OK
NG



OK

13.REPLACE CRANKSHAFT POSITION SENSOR

NG

REPLACE EGR VALVE ASSEMBLY

Click hereEngine / Hybrid System>M15A-FXE (EMISSION CONTROL)>EGR VALVE>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the EGR valve assembly.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



13.REPLACE CRANKSHAFT POSITION SENSOR

NEXT

14.CLEAR DTC
14.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P319000 OR P319100)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P319000 OR P319100)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

c.

None.


Result:
Result Proceed to
DTCs are not output A
P319000 or P319100 is output B



A

END

B

16.REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)
16.REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

NEXT

17.CLEAR DTC
17.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

18.CHECK WHETHER DTC OUTPUT RECURS (DTC P319000 OR P319100)
18.CHECK WHETHER DTC OUTPUT RECURS (DTC P319000 OR P319100)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

c.

None.


Result:
Result Proceed to
DTCs are not output A
P319000 or P319100 is output B



A

END

B

19.REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)
19.REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

NEXT

20.CLEAR DTC
20.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

21.CHECK WHETHER DTC OUTPUT RECURS (DTC P319000 OR P319100)
21.CHECK WHETHER DTC OUTPUT RECURS (DTC P319000 OR P319100)

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

c.

None.


Result:
Result Proceed to
DTCs are not output A
P319000 or P319100 is output B



A

END

B

22.REPLACE ECM
22.REPLACE ECM
HINT:

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

23.CLEAR DTC
23.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
24.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

Pre-procedure1

a.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Post-procedure1

c.

None.


Result:
Proceed to
NEXT



NEXT

END

25.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.


Result:
Proceed to
OK
NG



OK

GO TO FUEL PUMP CONTROL CIRCUIT

NG

REPAIR OR REPLACE FUEL SYSTEM