Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P001600  Crankshaft Position - Camshaft Position Correlation - Bank 1 Sensor A  P001700  Crankshaft Position - Camshaft Position Correlation - Bank 1 Sensor B  


DESCRIPTION

In the VVT system, the appropriate intake and exhaust valve open and close timing is controlled by the ECM. The ECM performs intake and exhaust valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve, and operating the camshaft timing gear; and 2) changing the relative positions of the gaps between the camshaft and crankshaft.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P001600 Crankshaft Position - Camshaft Position Correlation - Bank 1 Sensor A Deviation in crankshaft position sensor (for intake camshaft) signal and camshaft position sensor signal (3 trip detection logic).
·

Mechanical system (Timing chain has jumped tooth or chain stretched)

·

Camshaft timing oil control valve assembly (for intake camshaft)

·

Oil control valve filter

·

Camshaft timing sprocket assembly

·

ECM


Comes on DTC stored Engine B
P001700 Crankshaft Position - Camshaft Position Correlation - Bank 1 Sensor B Deviation in crankshaft position sensor signal and camshaft position sensor (for exhaust camshaft) signal (3 trip detection logic).
·

Mechanical system (Timing chain has jumped tooth or chain stretched)

·

Camshaft timing oil control valve assembly (for exhaust camshaft)

·

Oil control valve filter

·

Camshaft timing exhaust gear assembly

·

ECM


Comes on DTC stored Engine B

WIRING DIAGRAM

Refer to DTC P001011 for camshaft timing oil control valve assembly (for intake camshaft).

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P001011

Refer to DTC P001311 for camshaft timing oil control valve assembly (for exhaust camshaft).

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P001311

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P001600 OR P001700)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Only P001600 is output A
Only P001700 is output B
DTC P001600 or P001700 and other DTCs are output C


HINT:

If any DTCs other than P001600 or P001700 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)

B

6.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)

C

GO TO DTC CHART

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INTAKE VVT OCV DUTY RATIO BANK 1)

Pre-procedure1

a.

Start the engine.


b.

Warm up the engine.


Procedure1

c.

Check the engine speed when operating the camshaft timing oil control valve assembly using the GTS.

Powertrain > Engine > Active Test
Active Test Display
Control the Intake VVT OCV Duty Ratio Bank 1
Data List Display
Intake VVT Change Angle Bank 1
Intake VVT OCV Control Duty Ratio Bank 1
50004 372 4 397,296
Result:
Result Proceed to
Engine changes from steady idling to rough idling or engine stalling A
No change in engine speed B



Post-procedure1

d.

None.



A

7.CHECK ENGINE MECHANICAL SYSTEM

B

3.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)
3.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

OK

4.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

4.INSPECT OIL CONTROL VALVE FILTER
A322749

Pre-procedure1

a.

Remove the oil control valve filter.

HINT:

Click hereEngine / Hybrid System>1KR-FE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY



Procedure1

b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

5.INSPECT CAMSHAFT TIMING SPROCKET ASSEMBLY

NG

CLEAN OR REPLACE OIL CONTROL VALVE FILTER

5.INSPECT CAMSHAFT TIMING SPROCKET ASSEMBLY

OK

12.CHECK WHETHER DTC OUTPUT RECURS

NG

REPLACE CAMSHAFT TIMING SPROCKET ASSEMBLY

6.PERFORM ACTIVE TEST USING GTS (CONTROL THE EXHAUST VVT OCV DUTY RATIO BANK 1)

Pre-procedure1

a.

Start the engine.


b.

Warm up the engine.


Procedure1

c.

Check the engine speed when operating the camshaft timing oil control valve assembly using the GTS.

Powertrain > Engine > Active Test
Active Test Display
Control the Exhaust VVT OCV Duty Ratio Bank 1
Data List Display
Exhaust VVT Change Angle Bank 1
Exhaust VVT OCV Control Duty Ratio Bank 1
50004 372 5 398,297
Result:
Result Proceed to
Engine changes from steady idling to rough idling or engine stalling A
No change in engine speed B



Post-procedure1

d.

None.



A

7.CHECK ENGINE MECHANICAL SYSTEM

B

8.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)
7.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.


Result:
Proceed to
OK
NG



OK

12.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

8.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

OK

9.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)

9.INSPECT OIL CONTROL VALVE FILTER
A425320

Pre-procedure1

a.

Remove the oil control valve filter.

HINT:

Click hereEngine / Hybrid System>1KR-FE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY



Procedure1

b.

Check that the filter is not clogged.

OK:

Filter is not clogged.



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

10.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

NG

CLEAN OR REPLACE OIL CONTROL VALVE FILTER

10.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

OK

11.CLEAR DTC

NG

REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

11.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

12.CHECK WHETHER DTC OUTPUT RECURS
12.CHECK WHETHER DTC OUTPUT RECURS

Pre-procedure1

a.

Start the engine and warm it up.


b.

Drive the vehicle for 20 minutes or more.


Procedure1

c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

DTCs are not output.



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

END

NG