Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P017100  System Too Lean Bank 1  P017200  System Too Rich Bank 1  


DESCRIPTION

The fuel trim relates to the feedback compensation value, not to the basic injection time. The fuel trim includes the short-term fuel trim and the long-term fuel trim.

The short-term fuel trim is the short-term fuel compensation used to maintain the air fuel ratio at its ideal theoretical value. The signal from the heated oxygen sensor indicates whether the air fuel ratio is rich or lean compared to the ideal theoretical value, triggering a reduction in the fuel volume if the air fuel ratio is rich, and an increase in the fuel volume if it is lean.

Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P017100 System Too Lean Bank 1 When air fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on lean side (3 trip detection logic).
·

Fuel injector assembly blockage

·

Intake manifold

·

Engine coolant temperature sensor

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in heated oxygen sensor (sensor 1) circuit

·

Heated oxygen sensor (sensor 1)

·

ECM


Come on DTC stored Engine B
P017200 System Too Rich Bank 1 When air fuel ratio feedback is stable after warming up engine, fuel trim is considerably in error on rich side (3 trip detection logic).
·

Fuel injector assembly blockage

·

Intake manifold

·

Engine coolant temperature sensor

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in heated oxygen sensor (sensor 1) circuit

·

Heated oxygen sensor (sensor 1)

·

ECM


Come on DTC stored Engine B

HINT:
·

When DTC P017100 is stored, the actual air fuel ratio is lean. When DTC P017200 is stored, the actual air fuel ratio is rich.

·

If the vehicle runs out of fuel, the air fuel ratio is lean and DTC P017100 may be stored. The MIL then illuminates.

·

If the total of the short-term fuel trim value and long-term fuel trim value is within 20%, the system functions normally.

·

When the air fuel learning value is 1.31 or more, DTC P017100 is stored.

·

When the air fuel learning value is 0.77 or less, DTC P017200 is stored.



WIRING DIAGRAM

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


These DTCs are detected when the vehicle is driven for approximately 20 minutes at a constant vehicle speed of between 80 and 100 km/h (50 and 62 mph) with the shift lever in the 5th position (a malfunction is detected if the learning value of the driving range deviates by 25%).

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P017100 OR P017200)
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
Result:
Result Proceed to
Only P017100 or P017200 is output A
P017100 or P017200 and other DTCs are output B


HINT:

If any DTCs other than P017100 or P017200 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

B

GO TO DTC CHART

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)

Pre-procedure1

a.

Warm up the engine at an engine speed of 2500 rpm for approximately 3 minutes.


Procedure1

b.

Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

Powertrain > Engine > Active Test
Active Test Display
Control the Injection Volume for A/F Sensor
Data List Display
Injection Volume
O2 Sensor Voltage B1S1
O2 Sensor Voltage B1S2
50004 372 8 277,1305,218

c.

Monitor the voltage output of the heated oxygen sensor (sensor 1) and heated oxygen sensor (sensor 2) (O2 Sensor Voltage B1S1 and O2 Sensor Voltage B1S2) displayed on the GTS.

HINT:
·

The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The heated oxygen sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor (sensor 2) has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



Result:

The heated oxygen sensors reacts in accordance with increases and decreases of the fuel injection volume:

+12.5% = Rich output:

Higher than 0.55 V

-12.5% = Lean output:

Below 0.4 V


A318963E03
0.135,0.417 0.75,0.615 0.615,0.198 10 false Case 0.74,0.333 2.375,0.833 1.635,0.5 10 false Heated Oxygen Sensor (Sensor 1) Output Voltage 2.729,0.333 4.583,0.865 1.854,0.531 10 false Heated Oxygen Sensor (Sensor 2) Output Voltage 5.042,0.417 6.938,0.917 1.896,0.5 10 false Main Suspected Trouble Area 0.615,1 2.083,1.323 1.469,0.323 10 false Injection Volume 0.854,1.281 2.323,1.604 1.469,0.323 8 false +12.5% 0.865,1.531 2.333,1.854 1.469,0.323 8 false -12.5% 0.615,2 2.083,2.323 1.469,0.323 10 false Output Voltage 0.729,2.271 1.333,2.656 0.604,0.385 8 false Higher than 0.55 V 0.688,2.573 2.156,2.896 1.469,0.323 8 false Below 0.4 V 2.115,2.458 2.615,2.844 0.5,0.385 10 false OK 2.615,1 4.083,1.323 1.469,0.323 10 false Injection Volume 3.01,1.313 4.479,1.635 1.469,0.323 8 false +12.5% 3.021,1.531 4.49,1.854 1.469,0.323 8 false -12.5% 5.875,1.938 6.031,2.135 0.156,0.198 10 false - 4.885,3.927 7.031,4.302 2.146,0.375 10 false - Heated oxygen sensor (sensor 1) 4.917,5.167 6.969,5.635 2.052,0.469 10 false - Extremely rich or lean actual air fuel ratio 4.917,5.583 6.854,5.99 1.938,0.406 10 false - Fuel injector assembly leak or blockage 4.917,6 7.052,6.406 2.135,0.406 10 false - Gas leak from exhaust system 4.917,6.26 7.052,6.667 2.135,0.406 10 false - Ignition system 4.917,6.521 7.052,6.927 2.135,0.406 10 false - Fuel pressure 4.917,6.781 6.677,7.271 1.76,0.49 10 false - Manifold absolute pressure sensor 4.917,7.177 6.719,7.729 1.802,0.552 10 false - Engine coolant temperature sensor 0.667,3.083 2.135,3.406 1.469,0.323 10 false Injection Volume 0.802,3.333 2.271,3.656 1.469,0.323 8 false +12.5% 0.823,3.594 2.292,3.917 1.469,0.323 8 false -12.5% 0.698,4 2.167,4.323 1.469,0.323 10 false Output Voltage 0.76,4.521 1.292,4.875 0.531,0.354 8 false Almost no reaction 2.135,4.531 3.604,4.854 1.469,0.323 10 false NG 2.615,3.083 4.083,3.406 1.469,0.323 10 false Injection Volume 3.021,3.333 4.49,3.656 1.469,0.323 8 false +12.5% 3.042,3.594 4.51,3.917 1.469,0.323 8 false -12.5% 2.667,4.01 4.135,4.333 1.469,0.323 10 false Output Voltage 2.635,4.406 3.854,4.771 1.219,0.365 8 false Higher than 0.55 V 2.958,4.656 4.427,4.979 1.469,0.323 8 false Below 0.4 V 4.281,4.521 5.75,4.844 1.469,0.323 10 false OK 0.667,5.167 2.135,5.49 1.469,0.323 10 false Injection Volume 0.896,5.688 2.365,6.01 1.469,0.323 8 false +12.5% 0.896,5.948 2.365,6.271 1.469,0.323 8 false -12.5% 0.667,6.417 2.135,6.74 1.469,0.323 10 false Output Voltage 0.813,6.854 1.344,7.24 0.531,0.385 8 false Almost no reaction 2.115,6.906 3.583,7.229 1.469,0.323 10 false NG 4.375,6.885 5.844,7.208 1.469,0.323 10 false NG 2.667,6.427 4.135,6.75 1.469,0.323 10 false Output Voltage 2.667,6.885 3.833,7.167 1.167,0.281 8 false Almost no reaction 2.667,5.177 4.135,5.5 1.469,0.323 10 false Injection Volume 3.115,5.688 4.583,6.01 1.469,0.323 8 false +12.5% 3.125,5.969 4.594,6.292 1.469,0.323 8 false -12.5% 2.615,2 4.083,2.323 1.469,0.323 10 false Output Voltage 2.656,2.313 3.99,2.604 1.333,0.292 8 false Higher than 0.55 V 2.958,2.542 4.427,2.865 1.469,0.323 8 false Below 0.4 V 4.354,2.427 4.854,2.813 0.5,0.385 10 false OK 0.26,1.896 0.875,2.094 0.615,0.198 10 false 1 0.26,3.906 0.875,4.104 0.615,0.198 10 false 2 0.25,6.188 0.865,6.385 0.615,0.198 10 false 3

The following procedure enables the technician to check and graph the voltage outputs of both the heated oxygen sensors.

To display the graph, enter the following menus:

Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / All Data / O2 Sensor Voltage B1S1 and O2 Sensor Voltage B1S2; then press the view button.

HINT:

If the vehicle is short of fuel, the air fuel ratio becomes lean and the heated oxygen sensor DTCs are recorded, and then the MIL illuminates.


Result:
Result Proceed to
Case 3 A
Case 2 B
Case 1 C



Post-procedure1

d.

None.



A

3.READ VALUE USING GTS (COOLANT TEMPERATURE)

B

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)

C

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P017100 OR P017200)
3.READ VALUE USING GTS (COOLANT TEMPERATURE)
a.

Read the Data List twice, when the engine is both cold and warmed up.

Powertrain > Engine > Data List
Tester Display
Coolant Temperature
50003 372 205
Standard:
GTS Display Condition Specified Condition
Coolant Temperature Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

NG

4.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Read the Intake Manifold Absolute Pressure value at ignition switch ON.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
50003 372 211,385,205
Result:
Result Proceed to
The value of Intake Manifold Absolute Pressure is between 80 and 110 kPa A
None of the above conditions are met B




A

5.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

B

5.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

Pre-procedure1

a.

Start the engine.


b.

Warm up the engine.


Procedure1

c.

Read the Intake Manifold Absolute Pressure value at idling.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
50003 372 211,385,205
Result:
Result Proceed to
The value of Intake Manifold Absolute Pressure is between 29 and 37 kPa A
None of the above conditions are met B



Post-procedure1

d.

None.



A

6.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

B

15.CHECK INTAKE SYSTEM
6.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)

Pre-procedure1

a.

Start the engine.


b.

Warm up the engine.


Procedure1

c.

Read the Intake Manifold Absolute Pressure value at 2500 rpm.

Powertrain > Engine > Data List
Tester Display
Engine Speed
Intake Manifold Absolute Pressure
Coolant Temperature
50003 372 211,385,205
Result:
Result Proceed to
The value of Intake Manifold Absolute Pressure is between 22 and 50 kPa A
None of the above conditions are met B



Post-procedure1

d.

None.



A

7.CHECK FOR SPARK (SPARK TEST)

B

15.CHECK INTAKE SYSTEM
7.CHECK FOR SPARK (SPARK TEST)

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

If the spark plugs or ignition system malfunctions, engine misfire may occur. The misfire count can be read using the GTS. Enter the following menus: Powertrain / Engine / Data List / All Data / Misfire Count Cylinder #1 (to Misfire Count Cylinder #3).



Result:
Proceed to
NEXT



NEXT

8.CHECK FOR EXHAUST GAS LEAK
8.CHECK FOR EXHAUST GAS LEAK
a.

Check the exhaust gas leaks.

OK:

No gas leaks.



Result:
Proceed to
OK
NG



OK

9.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE EXHAUST SYSTEM

9.CHECK FUEL PRESSURE

OK

10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)

NG

REPAIR OR REPLACE FUEL SYSTEM

10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
a.

Check the injection and volume.

HINT:
·

Refer to the fuel injector assembly inspection procedure.

Click hereEngine / Hybrid System>1KR-FE (FUEL)>FUEL INJECTOR>INSPECTION

·

If the fuel injector assemblies malfunction, engine misfire may occur. The misfire count can be read using the GTS. Enter the following menus: Powertrain / Engine / Data List / All Data / Misfire Count Cylinder #1 (to Misfire Count Cylinder #3).




Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)

NG

REPLACE FUEL INJECTOR ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)

Pre-procedure1

a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D38-4 (OX1A) - D50-126 (OX1A) Always Below 1 Ω
D38-2 (HT1A) - D50-25 (HT1A) Always Below 1 Ω
D38-3 (E1) - D50-125 (E11) Always Below 1 Ω
D38-4 (OX1A) or D50-126 (OX1A) - Body ground Always 10 kΩ or higher
D38-2 (HT1A) or D50-25 (HT1A) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

12.REPLACE HEATED OXYGEN SENSOR (SENSOR 1)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE HEATED OXYGEN SENSOR (SENSOR 1)

NEXT

13.CLEAR DTC
13.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P017100 OR P017200)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P017100 OR P017200)

Pre-procedure1

a.

Start the engine and warm it up.


b.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


Procedure1

c.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
P017100 or P017200 is output A
DTCs are not output B


Post-procedure1

d.

None.



A

B

END

15.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

HINT:

Click hereEngine / Hybrid System>1KR-FE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION


OK:

No leaks in intake system.



b.

Check the intake manifold.

OK:

The intake manifold is not cracked.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE INTAKE SYSTEM