44785
1.INSTALL BRAKE BOOSTER GASKET
Install a new brake booster gasket to the brake booster assembly.
44610
2.INSTALL BRAKE BOOSTER ASSEMBLY
Temporarily install the brake booster assembly to the vehicle body.
Do not apply excessive force to the brake lines.
Temporarily install the lock nut and brake master cylinder push rod clevis to the brake booster assembly.
Fully tighten the lock nut when adjusting the brake pedal height.
Install the 4 nuts to secure the brake booster assembly.
Tighten the 4 nuts in the order shown in the illustration.
| *a | Torque Wrench Fulcrum Length |
Using a union nut wrench, connect the 2 brake lines to the brake actuator assembly.
Do not kink or damage the brake lines.
Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):
17.4 N*m (177 kgf*cm, 13 ft.*lbf)
for G16E-GTS:
Engage the 5 clamps to install a new No. 1 brake tube clamp to the brake lines.
Engage the clamp and install a new No. 2 brake tube clamp to the vehicle body.
Engage the 5 clamps to install the brake lines to the No. 2 brake tube clamp.
except G16E-GTS:
Engage the 5 clamps to install a new No. 2 brake tube clamp to the brake lines.
Engage the clamp and install a new No. 1 brake tube clamp to the vehicle body.
Engage the 5 clamps to install the brake lines to the No. 1 brake tube clamp.
Remove the protective tape.
w/ Vacuum Warning Switch:
Connect the vacuum warning switch connector.
w/ Vacuum Sensor:
Connect the vacuum sensor connector.
Engage the clamp.
Install the engine room main wire with the bolt.
47264A
3.INSTALL PUSH ROD PIN
47101A
4.INSTALL BRAKE PEDAL RETURN SPRING
45260
5.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45259A
6.INSTALL COLUMN HOLE COVER SILENCER SHEET
55606
7.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
44773F
8.CONNECT UNION TO CHECK VALVE HOSE
| *A | for M15A-FKS |
| *B | for G16E-GTS |
| *a | Paint Mark |
Connect the union to check valve hose to the brake booster assembly and slide the clip to secure it.
When connecting the union to check valve hose, face the paint mark up.
Make sure that the tabs of the clip are facing upward.
44772
9.CONNECT CHECK VALVE TO CONNECTOR TUBE HOSE (for 1KR-FE)
| *a | Paint Mark |
Install the vacuum hose assembly to the vehicle body with the 2 nuts.
Connect the check valve to connector tube hose to the brake booster assembly and slide the clip to secure it.
When connecting the check valve to connector tube hose, make sure that the paint mark is facing the front of the vehicle.
Make sure that the tabs of the clip are facing the front of the vehicle.
55225C
10.INSTALL DASH PANEL HEAT INSULATOR
for M15A-FKS:
Temporarily install the dash panel heat insulator to the vehicle body with the 2 nuts (B).
Install the nut (A).
Tighten the 2 nuts (B).
for G16E-GTS:
Temporarily install the dash panel heat insulator to the vehicle body with the nut (A) and clamp.
Install the nut (B).
Tighten the nut (A).
51451A
11.INSTALL CENTER ENGINE UNDER COVER (for M15A-FKS)
51410
12.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY (for G16E-GTS)
74404A
13.INSTALL BATTERY CLAMP SUB-ASSEMBLY
for M15A-FKS:
Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for 1KR-FE:
Click hereEngine / Hybrid System>1KR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
17701
14.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
for M15A-FKS:
Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for 1KR-FE:
Click hereEngine / Hybrid System>1KR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
15.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE
for M15A-FKS:
Click hereEngine / Hybrid System>M15A-FKS (ENGINE MECHANICAL)>ENGINE ASSEMBLY>INSTALLATION
for 1KR-FE:
Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>THROTTLE BODY>INSTALLATION
89661
16.INSTALL ECM
for M15A-FKS:
Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>ECM>INSTALLATION
for 1KR-FE:
Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>ECM>INSTALLATION
47201
17.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY
for TMC Model:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER (for Gasoline Model TMC Made LHD)>INSTALLATION
for TMMF Made:
Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE MASTER CYLINDER (for Gasoline Model TMMF Made LHD)>INSTALLATION
18.INSPECT AND ADJUST BRAKE PEDAL