The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during radiator assembly removal/installation are shown below.
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
Learning completes when vehicle is operated normally
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
Click hereGeneral>MAINTENANCE>G16E-GTS AUXILIARY BATTERY>REMOVAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If an SRS part is accidentally deployed, it may cause a serious injury.
51410
3.REMOVE NO. 1 ENGINE UNDER COVER ASSEMBLY
4.DRAIN ENGINE COOLANT
5.REMOVE HEADLIGHT ASSEMBLY LH
6.REMOVE HEADLIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
17753
7.REMOVE NO. 3 AIR CLEANER INLET
Disengage the 2 claws to remove the No. 3 air cleaner inlet from the vehicle.
17751
8.REMOVE NO. 1 AIR CLEANER INLET
Remove the 2 clips and No. 1 air cleaner inlet from the vehicle.
16681A
9.REMOVE RADIATOR UPPER AIR GUIDE PLATE
52611
10.REMOVE FRONT BUMPER ENERGY ABSORBER
53288A
11.REMOVE COOL AIR INTAKE DUCT
Remove the 3 clips and cool air intake duct from the vehicle.
52131A
12.REMOVE FRONT BUMPER REINFORCEMENT
53510
13.REMOVE HOOD LOCK ASSEMBLY
53205
14.REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
Disconnect the 2 airbag connectors.
When disconnecting any airbag connector, take care not to damage the airbag wire harness.
Refer to How to Connect or Disconnect Airbag Connector:
| *A | for RHD |
| *B | for LHD |
Disconnect the hood lock control cable assembly from the upper radiator support sub-assembly.
Disconnect the airbag connector.
Disconnect the airbag connector.
Disconnect the horn connector.
Disengage the 3 clamps.
Disengage the clamp.
Disengage the 3 clamps to disconnect the wire harness from the upper radiator support sub-assembly.
Disengage the clamps to disconnect the No. 3 water by-pass hose from the upper radiator support sub-assembly.
Remove the 4 bolts and upper radiator support sub-assembly from the front side member bracket sub-assembly.
16695A
15.REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE LH
16691A
16.REMOVE FRONT RADIATOR SIDE AIR GUIDE PLATE RH
16595D
17.REMOVE NO. 1 RADIATOR AIR GUIDE LH
Disengage the 2 clamps and disconnect the wire harness.
Disengage the claw and 2 guides to remove the No. 1 radiator air guide LH.
16593B
18.REMOVE NO. 1 RADIATOR AIR GUIDE RH
Disengage the claw and 2 guides to remove the No. 1 radiator air guide LH.
16261
19.DISCONNECT WATER BY-PASS HOSE
Disengage the clamp.
Slide the clip and disconnect the water by-pass hose from the radiator assembly.
16267K
20.DISCONNECT NO. 3 WATER BY-PASS HOSE
Slide the clip and disconnect the No. 3 water by-pass hose from the radiator assembly.
16571C
21.DISCONNECT NO. 1 RADIATOR HOSE
Slide the clip and disconnect the No. 1 radiator hose from the radiator assembly.
16572D
22.DISCONNECT NO. 2 RADIATOR HOSE
Slide the clip and disconnect the No. 2 radiator hose from the radiator assembly.
88460
23.SEPARATE COOLER CONDENSER ASSEMBLY
Remove the 3 bolts.
Disengage the guide to separate the cooler condenser assembly from the radiator assembly.
Do not damage the cooler condenser assembly or radiator assembly when removing the cooler condenser assembly.
17344E
24.SEPARATE NO. 4 AIR HOSE
17343D
25.SEPARATE NO. 3 AIR HOSE
17940D
26.REMOVE INTERCOOLER ASSEMBLY
16400
27.REMOVE RADIATOR ASSEMBLY
Remove the radiator assembly together with the fan shroud from the vehicle body.
Do not apply excessive force to the cooler condenser assembly or pipe when removing the radiator assembly with the fan shroud.
Disengage the 2 claws and 2 guides to remove the fan shroud from the radiator assembly.
Do not damage the radiator assembly when removing the fan shroud.
16523A
28.REMOVE RADIATOR SUPPORT CUSHION
Remove the 2 radiator support cushions from the radiator assembly.
16535
29.REMOVE LOWER RADIATOR SUPPORT
Remove the 2 lower radiator supports from the radiator assembly.
30.REMOVE RADIATOR DRAIN COCK PLUG
Remove the radiator drain cock plug.
Remove the O-ring from the radiator drain cock plug.