The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the parking brake cable assembly removal/installation are shown below.
When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.
Touching high-temperature areas such as the engine and exhaust pipe could result in burns.
Immediately after installing the brake shoes, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.
After replacing the brake shoes, the brake pedal may feel soft due to clearance between the rear brake shoe and brake drum. Depress the brake pedal several times until the brake pedal feels firm.
After replacing the brake shoes, always perform a road test to check the braking performance and check for vibrations.
When removing or installing the brake shoes or pushing back the wheel brake cylinder piston may cause a large clearance between the brake shoes and brake drum. When the brake pedal is depressed with a large clearance between the brake shoes and the brake drum, DTC C13DC00, C13DE00, C140000 related to abnormal brake fluid pressure may be stored. Make sure to clear any DTCs after performing this procedure. (for HV Model TMC Made)
While the auxiliary battery is connected, even if the power switch is off, the brake control system activates when the brake pedal is depressed or any door courtesy switch turns on. Therefore, when servicing the brake system components, do not operate the brake pedal or open/close the doors while the auxiliary battery is connected. (for HV Model TMC Made)
When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is operated normally
1. PRECAUTION (for HV Model TMC Made)
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
58911A
2.REMOVE NO. 1 BOX SIDE PANEL (for TMC Made)
58912C
3.REMOVE NO. 2 BOX SIDE PANEL (for TMC Made)
58903A
4.REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY (for TMC Made)
58857A
5.REMOVE UPPER NO. 1 CONSOLE SUPPORT BRACKET (for TMC Made)
58903A
6.REMOVE CONSOLE REAR END PANEL SUB-ASSEMBLY (for Gasoline Model TMMF Made)
58911A
7.REMOVE NO. 1 BOX SIDE PANEL (for HV Model TMMF Made)
58912C
8.REMOVE NO. 2 BOX SIDE PANEL (for HV Model TMMF Made)
58857A
9.REMOVE UPPER NO. 1 CONSOLE SUPPORT BRACKET (for HV Model TMMF Made)
10.LOOSEN PARKING BRAKE CABLE ASSEMBLY
11.DISCONNECT PARKING BRAKE CABLE ASSEMBLY
04495
12.REMOVE REAR BRAKE SHOE KIT (for TMC Made)
04495
13.REMOVE REAR BRAKE SHOE KIT (for TMMF Made)
51447D
14.REMOVE CENTER NO. 4 ENGINE UNDER COVER (for TMC Made)
51447D
15.REMOVE CENTER NO. 4 ENGINE UNDER COVER (for TMMF Made)
57543C
16.REMOVE CENTER NO. 1 FLOOR BRACE (for TMMF Made)
17410
17.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for 1KR-FE)
17410
18.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for M15A-FKS)
17410
19.REMOVE FRONT EXHAUST PIPE ASSEMBLY (for M15A-FXE)
58166A
20.REMOVE FRONT FLOOR COVER LH (w/ Cover)
58165C
21.REMOVE FRONT FLOOR COVER RH (w/ Cover)
Use the same procedure as for the LH side.
57628E
22.REMOVE REAR FLOOR SIDE MEMBER COVER LH (w/ Cover)
57627G
23.REMOVE REAR FLOOR SIDE MEMBER COVER RH (w/ Cover)
Use the same procedure as for the LH side.
58151
24.REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR (for TMMF Made)
58153
25.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR (for TMC Made)
58153
26.REMOVE FRONT NO. 2 FLOOR HEAT INSULATOR (for TMMF Made)
77606
27.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for Gasoline Model)
77606
28.REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY (for HV Model)
46430
29.REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Gasoline Model TMC Made)
Remove the 4 bolts, nut and No. 3 parking brake cable assembly.
46430
30.REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for HV Model TMC Made)
Remove the 4 bolts, nut and No. 3 parking brake cable assembly.
46430
31.REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for TMMF Made)
Disengage the claw to separate the No. 3 parking brake cable assembly.
Remove the 3 bolts, nut and No. 3 parking brake cable assembly.
46420
32.REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for Gasoline Model TMC Made)
Remove the 5 bolts, nut and No. 2 parking brake cable assembly.
46420
33.REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for HV Model TMC Made)
Remove the 5 bolts, nut and No. 2 parking brake cable assembly.
46420
34.REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for TMMF Made)
Disengage the claw to separate the No. 2 parking brake cable assembly.
Remove the 4 bolts, nut and No. 2 parking brake cable assembly.