Home › TRANSMISSION ยท A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION SYSTEM (for 2UZ-FE)

AUTOMATIC TRANSMISSION SYSTEM (for 2UZ-FE) > PROBLEM SYMPTOMS TABLE

for Preparation Click here


HINT:
If a normal code is displayed during the diagnostic trouble code check although the trouble still occurs, check the electrical circuits for each symptom in the order given in the charts on the following pages and proceed to the page given for troubleshooting.
The Matrix Chart is divided into 3 chapters.
Chapter 1:
Refer to the table below when the trouble cause is considered to be electrical.
If the instruction "Proceed to next circuit inspection shown on matrix chart" is given in the flow chart of each circuit, proceed to the circuit with the next highest number in the table to continue the check.
If the trouble still occurs even though there are no abnormalities in any of the other circuits, check and replace the ECM.


1. Chapter 1: Electronic Circuit Matrix Chart 
Symptom
Suspected area
See page
No up-shift (A particular gear, from 1st to 4th gear, is not up-shifted)
1. Shift solenoid valve (S1) circuit *1
Click here
2. Shift solenoid valve (S2) circuit *1
Click here
3. ECM
Click here
No up-shift (4th -> 5th)
1. Transmission control switch circuit (D - 4) *1
Click here
2. Engine coolant temp. sensor circuit *1
Click here
3. Speed sensor NT circuit *1
Click here
4. Shift solenoid valve (SL1) circuit *1
Click here
5. Shift solenoid valve (SL2) circuit *1
Click here
6. Shift solenoid valve (SR) circuit *1
Click here
7. ECM
Click here
No up-shift (3rd -> 4th)
1. Engine coolant temp. sensor circuit *1
Click here
2. Shift solenoid valve (S2) circuit *1
Click here
3. ECM
Click here
No up-shift (1st -> 2nd)
1. Transmission control switch circuit (2 - L) *1
Click here
2. Shift solenoid valve (S2) circuit *1
Click here
3. ECM
Click here
No down-shift (5th -> 4th)
1. Transmission control switch circuit (D - 4) *1
Click here
2. Shift solenoid valve (SL1) circuit *1
Click here
3. Shift solenoid valve (SL2) circuit *1
Click here
4. Shift solenoid valve (SR) circuit *1
Click here
5. ECM
Click here
No down-shift (2nd -> 1st)
1. Transmission control switch circuit (2 - L) *1
Click here
2. Shift solenoid valve (S2) circuit *1
Click here
3. ECM
Click here
No down-shift (A particular gear, from 1st to 4th gear, is not down-shifted)
1. Shift solenoid valve (S1) circuit *1
Click here
2. Shift solenoid valve (S2) circuit *1
Click here
3. ECM
Click here
No lock-up
1. ATF temperature sensor circuit *1
Click here
2. Transfer L4 position switch circuit *1
Click here
3. Stop light switch circuit *1
Click here
4. Speed sensor NT circuit *1
Click here
5. Shift solenoid valve (SLU) circuit *1
Click here
6. Engine coolant temp. sensor circuit *1
Click here
7. ECM
Click here
No lock-up off
1. Shift solenoid valve (SLU) circuit *1
Click here
2. ECM
Click here
Shift point too high or too low
1. Shift solenoid valve (SLT) circuit *1
Click here
2. Speed sensor NT circuit *1
Click here
3. Speed sensor SP2 circuit *1
Click here
4. Throttle position sensor circuit *1
Click here
5. ATF temperature sensor circuit *1
Click here
6. Transfer L4 position switch circuit *1
Click here
7. ECM
Click here
Up-shift to 5th from 4th while shift lever is in 4 position
1. Transmission control switch circuit (D - 4) *1
Click here
2. ECM
Click here
Up-shift to 5th from 4th while engine is cold
1. Engine coolant temp. sensor circuit *1
Click here
2. ECM
Click here
Up-shift to 4th from 3rd while shift lever is in 3 position
1. Park/neutral position switch circuit *1
Click here
2. ECM
Click here
Up-shift to 3rd from 2nd while shift lever is in 2 position
1. Park/neutral position switch circuit *1
Click here
2. ECM
Click here
Up-shift to 2nd from 1st while shift lever is in L position
1. Transmission control switch circuit (2 - L) *1
Click here
2. ECM
Click here
Harsh engagement (N -> D)
1. Speed sensor NT circuit *1
Click here
2. Shift solenoid valve (SL1) circuit *1
Click here
3. Shift solenoid valve (SLT) circuit *1
Click here
4. ECM
Click here
Harsh engagement (Lock-up)
1. Speed sensor NT circuit *1
Click here
2. Speed sensor SP2 circuit *1
Click here
3. Shift solenoid valve (SLU) circuit *1
Click here
4. ECM
Click here
Harsh engagement (Any driving position)
ECM
Click here
Poor acceleration
1. ATF temperature sensor No. 2 circuit
Click here
2. Engine coolant temp. sensor circuit *1
Click here
3. Shift solenoid valve (SLT) circuit *1
Click here
4. ECM
Click here
No engine braking
ECM
Click here
No kick-down
ECM
Click here
Engine stalls when starting off or stopping
1. Shift solenoid valve (SLU) circuit *1
Click here
2. ECM
Click here
AT Oil Temp. warning light remains on, Lock-up at 3rd gear and/or shift point too high
1. ATF temperature sensor No. 2 circuit
Click here
2. Engine coolant temp. sensor circuit
Click here
3. ECM
Click here
Malfunction in shifting
1. Park/neutral position switch circuit *1
Click here
2. ECM
Click here

HINT:
*1: When the circuit is detective, a DTC may be output.


2. Chapter 2: On-vehicle Repair 
Symptom
Suspected area
See page
Vehicle does not move with shift lever in any forward position and reverse position
1. Transmission control cable
Click here
2. Manual valve
Click here
3. Parking lock pawl
Click here
4. Off-vehicle repair matrix chart
-
Vehicle does not move with shift lever in R position
1. Valve body assembly
Click here
2. Off-vehicle repair matrix chart
-
No up-shift (1st -> 2nd)
1. Valve body assembly
Click here
2. Off-vehicle repair matrix chart
-
No up-shift (2nd -> 3rd)
1. Valve body assembly
Click here
2. Off-vehicle repair matrix chart
-
No up-shift (3rd -> 4th)
1. Valve body assembly
Click here
2. Off-vehicle repair matrix chart
-
No up-shift (4th -> 5th)
1. Valve body assembly
Click here
2. Off-vehicle repair matrix chart
-
No down-shift (5th -> 4th)
1. Valve body assembly
Click here
2. Off-vehicle repair matrix chart
-
No down-shift (4th -> 3rd)
1. Valve body assembly
Click here
2. Off-vehicle repair matrix chart
-
No down-shift (3rd -> 2nd)
1. Valve body assembly
Click here
2. Off-vehicle repair matrix chart
-
No down-shift (2nd -> 1st)
1. Valve body assembly
Click here
2. Off-vehicle repair matrix chart
-
No lock-up or No lock-up off
1. Shift solenoid valve (SLU)
Click here
2. Valve body assembly
Click here
3. Off-vehicle repair matrix chart
-
Harsh engagement (N -> D)
1. Shift solenoid valve (SL1)
Click here
2. Valve body assembly
Click here
3. C1 accumulator
Click here
4. Off-vehicle repair matrix chart
-
Harsh engagement (Lock-up)
1. Shift solenoid valve (SLU)
Click here
2. Valve body assembly
Click here
3. Off-vehicle repair matrix chart
-
Harsh engagement (N -> R)
1. Shift solenoid valve (SLT)
Click here
2. Shift solenoid valve (SLU)
Click here
3. Valve body assembly
Click here
4. C3 accumulator
Click here
5. Off-vehicle repair matrix chart
-
Harsh engagement (1st -> 2nd -> 3rd -> 4th -> 5th)
1. Shift solenoid valve (SLT)
Click here
2. Shift solenoid valve (SL1)
Click here
3. Valve body assembly
Click here
Harsh engagement (1st -> 2nd)
1. Valve body assembly
Click here
2. B3 accumulator
Click here
3. Off-vehicle repair matrix chart
-
Harsh engagement (2nd -> 3rd)
1. Valve body assembly
Click here
2. C3 accumulator
Click here
3. Off-vehicle repair matrix chart
-
Harsh engagement (3rd -> 4th)
1. Valve body assembly
Click here
2. C2 accumulator
Click here
3. Off-vehicle repair matrix chart
-
Harsh engagement (4th -> 5th)
1. Shift solenoid valve (SL1)
Click here
2. Shift solenoid valve (SL2)
Click here
3. Valve body assembly
Click here
4. Off-vehicle repair matrix chart
-
Harsh engagement (5th -> 4th)
1. Shift solenoid valve (SL1)
Click here
2. Shift solenoid valve (SL2)
Click here
3. Valve body assembly
Click here
4. Off-vehicle repair matrix chart
-
Slip or shudder (Forward and reverse)
1. Transmission control cable
Click here
2. Valve body assembly
Click here
3. Oil strainer
Click here
4. Off-vehicle repair matrix chart
-
No engine braking (1st: L position)
1. Valve body assembly
Click here
2. Off-vehicle repair matrix chart
-
No engine braking (2nd: 2 position)
1. Valve body assembly
Click here
2. Off-vehicle repair matrix chart
-
No kick-down
Valve body assembly
Click here
Shift point too high or too low
1. Shift solenoid valve (SLT)
Click here
2. Shift solenoid valve (SL1)
Click here
3. Valve body assembly
Click here
Poor acceleration
1. Shift solenoid valve (SLT)
Click here
2. Valve body assembly
Click here
Engine stalls when starting off or stopping
1. Shift solenoid valve (SLU)
Click here
2. Valve body assembly
Click here

3. Chapter 3: Off-Vehicle Repair 
Symptom
Suspected area
See page
Vehicle does not move with shift lever in any forward position and reverse position
1. Rear planetary gear unit
Click here
2. Torque converter clutch
Click here
Vehicle does not move with shift lever in R position
1. Brake No. 4 (B4)
Click here
2. Clutch No. 3 (C3)
Click here
3. One-way clutch No. 1 (F1)
Click here
No up-shift (1st -> 2nd)
1. Brake No. 3 (B3)
Click here
2. One-way clutch No. 1 (F1)
Click here
3. One-way clutch No. 2 (F2)
Click here
No up-shift (2nd -> 3rd)
Clutch No. 3 (C3)
Click here
No up-shift (3rd -> 4th)
Clutch No. 2 (C2)
Click here
No up-shift (4th -> 5th)
1. Brake No. 1 (B1)
Click here
2. Clutch No. 1 (C1)
Click here
No lock-up or No lock-up off
Torque converter clutch
Click here
Harsh engagement (N -> D)
1. Clutch No. 1 (C1)
Click here
2. One-way clutch No. 3 (F3)
Click here
Harsh engagement (N -> R)
1. Clutch No. 3 (C3)
Click here
2. Brake No. 4 (B4)
Click here
3. One-way clutch No. 1 (F1)
Click here
Harsh engagement (1 -> 2)
1. Brake No. 3 (B3)
Click here
2. One-way clutch No. 1 (F1)
Click here
3. One-way clutch No. 2 (F2)
Click here
Harsh engagement (2 -> 3)
Clutch No. 3 (C3)
Click here
Harsh engagement (3 -> 4)
Clutch No. 2 (C2)
Click here
Harsh engagement (4 -> 5th)
1. Brake No. 1 (B1)
Click here
2. Clutch No. 1 (C1)
Click here
Harsh engagement (Lock-up)
Torque converter clutch
Click here
Slip or shudder (Forward and reverse: After warm-up)
1. One-way clutch No. 1 (F1)
Click here
2. Clutch No. 3 (C3)
Click here
3. Torque converter clutch
Click here
Slip or shudder (Particular position: Just after engine starts)
Torque converter clutch
Click here
Slip or shudder (R position)
1. Brake No. 4 (B4)
Click here
2. One-way clutch No. 1 (F1)
Click here
3. Clutch No. 3 (C3)
Click here
Slip or shudder (1st)
1. Clutch No. 1 (C1)
Click here
2. One-way clutch No. 3 (F3)
Click here
Slip or shudder (2nd)
1. Clutch No.1 (C1)
Click here
2. Brake No. 3 (B3)
Click here
3. One-way clutch No. 1 (F1)
Click here
4. One-way clutch No. 2 (F2)
Click here
Slip or shudder (3rd)
1. Clutch No. 1 (C1)
Click here
2. Clutch No. 3 (C3)
Click here
3. One-way clutch No. 1 (F1)
Click here
Slip or shudder (4th)
1. Clutch No. 1 (C1)
Click here
2. Clutch No. 2 (C2)
Click here
Slip or shudder (5th)
1. Clutch No. 2 (C2)
Click here
2. Clutch No. 3 (C3)
Click here
3. Brake No. 1 (B1)
Click here
No engine braking (1st - 4th: D position)
Clutch No. 1 (C1)
Click here
No engine braking (1st: L position)
Brake No. 4 (B4)
Click here
No engine braking (2nd: 2 position)
Brake No. 2 (B2)
Click here
No engine braking (3rd: 3 position)
Brake No. 1 (B1)
Click here
Poor acceleration (All positions)
Torque converter clutch
Click here
Poor acceleration (5th)
1. Clutch No. 1 (C1)
Click here
2. Clutch No. 3 (C3)
Click here
3. Brake No. 1 (B1)
Click here
4. Front planetary gear unit
Click here
Engine stalls when starting off or stopping
Torque converter clutch
Click here