Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM › from 2014.08
RM1440E _51 Engine / Hybrid System _056124 1GR-FE ENGINE CONTROL _0273876 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2440  Secondary Air Injection System Switching Valve Stuck Open Bank1  P2441  Secondary Air Injection System Switching Valve Stuck Close Bank1  P2442  Secondary Air Injection System Switching Valve Stuck Open Bank 2  P2443  Secondary Air Injection System Switching Valve Stuck Closed Bank 2  


DESCRIPTION

Refer to DTC P0412 (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>P0412).

DTC No. DTC Detection Condition Trouble Area
P2440 Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
·

NO. 1 emission control valve set

·

Open or short in NO. 1 emission control valve circuit

·

Air injection system piping

·

Pressure sensor

·

Pressure sensor circuit

·

Air injection control driver

·

ECM


The emission control valve set (for bank 1) is stuck open for 7 seconds while the engine is running (2 trip detection logic).
P2441 The emission control valve set (for bank 1) is stuck closed for 7 seconds while the engine is running (2 trip detection logic).
·

NO. 1 emission control valve set

·

Open or short in NO. 1 emission control valve circuit

·

Air injection system piping

·

Pressure sensor

·

Pressure sensor circuit

·

Air injection control driver

·

ECM

·

Open or short in air pump heater circuit

·

Air pump heater relay (AIR PUMP HTR)

·

Air pump assembly


P2442 Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic).
·

NO. 2 emission control valve set

·

Open or short in NO. 2 emission control valve circuit

·

Air injection system piping

·

Pressure sensor

·

Pressure sensor circuit

·

Air injection VSV relay (AI-VSV)

·

ECM


The NO. 2 emission control valve set (for bank 2) is stuck open for 7 seconds while the engine is running (2 trip detection logic).
P2443 The NO. 2 emission control valve set (for bank 2) is stuck closed for 7 seconds while the engine is running (2 trip detection logic).
·

NO. 2 emission control valve set

·

Open or short in NO. 2 emission control valve circuit

·

Air injection system piping

·

Pressure sensor

·

Pressure sensor circuit

·

Air injection VSV relay (AI-VSV)

·

ECM

·

Open or short in air pump heater circuit

·

Air pump heater relay (AIR PUMP HTR)

·

Air pump assembly



HINT:

Emission control valve normal operation:

When the emission control valve is open, exhaust gas pulsation occurs in the secondary air passage.

When the emission control valve is closed, exhaust gas pulsation does not occur in the secondary air passage.


CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the GTS on.

6.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON and turn the GTS on.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

10.

Start the engine after the GTS initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

Perform the following to confirm the secondary air injection system pending codes: Press ENTER (Exit).

13.

Check for pending DTCs.

OK:

No pending DTC is output.


14.

After Secondary Air Injection Check is completed, check All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P2440, P2441, P2442 or P2443.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Refer to "Data List / Active Test" [Air Pump Pressure (Absolute), Air Pump2 Pressure (Absolute) and Air Pump Pulsation Pressure] (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST).


HINT:

Determination by ECM monitoring:

The ECM detects malfunctions in the secondary air injection system by detecting the pressure in the secondary air injection passage between the air pump and emission control valve and stores a DTC. Soon after a cold engine start, the monitor runs for a short time while the secondary air injection system is both ON and OFF. The ECM detects both the pressure and the exhaust pulsation and compares them.

The following 8 patterns are secondary air injection system pressure conditions in the secondary air injection system passage.


Pressure Condition in Secondary Air Injection System Case 1
Air Pump ON
Emission Control Valve Open
Pressure 1 kPa or higher
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 2
Air Pump OFF
Emission Control Valve Open
Pressure Below 3 kPa
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 3
Air Pump ON
Emission Control Valve Closed
Pressure 1 kPa or higher
Pulsation Detection Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 4
Air Pump OFF
Emission Control Valve Closed
Pressure Below 3 kPa
Pulsation Detection Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 5
Air Pump ON
Emission Control Valve Open
Pressure 1 kPa or higher
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 6
Air Pump OFF
Emission Control Valve Open
Pressure Below 3 kPa
Pulsation Detection Exhaust gas pulsation detected

Pressure Condition in Secondary Air Injection System Case 7
Air Pump ON
Emission Control Valve Closed
Pressure 1 kPa or higher
Pulsation Detection Exhaust gas pulsation not detected

Pressure Condition in Secondary Air Injection System Case 8
Air Pump OFF
Emission Control Valve Closed
Pressure Below 3 kPa
Pulsation Detection Exhaust gas pulsation not detected

If the detected pressure is high, the air pump is assumed to be ON and if it alternates sharply, the emission control valve is assumed to be open. The ECM detects malfunctions from the combination of pressures detected when the secondary air injection system is ON and OFF.

HINT:

The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.


HINT:
·

In cases 3 and 7, as the pressure sensor detects a slight pump operation pulsation, the detected value is not constant. Since the pump outlet is blocked by closing the emission control valve, the average pressure is higher than in case 1 (approximately 15 to 25 kPa).

·

In case 1, the average pressure is approximately 3 to 11 kPa. The value of 1 kPa indicated in the table above is a threshold for detecting pump malfunctions.



Detected Condition while Secondary Air Injection Operating:
Air Pump ON, Emission Control Valve Open
Detected Condition while Secondary Air Injection not Operating:
Air Pump OFF, Emission Control Valve Closed
ECM Determination DTC Output
Case 1 Case 8 Normal or emission control valve set stuck Closed -
or
P2441
or
P2443
Case 1 Case 6 Emission control valve set stuck open P2440 and P2442
or
P2442
Case 1 Case 7 Normal -
Case 2 Case 8 Air pump assembly stuck OFF P2445
Case 3 Case 8 Normal -
Case 1 Case 5 Normal -
Case 2 Case 6 Emission control valve stuck open and air pump stuck OFF P2440 and/or P2442
and
P2445
Case 3 Case 7 Normal -
Case 4 Case 8 Normal -

HINT:
·

By using the GTS to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, pending codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



System Check:

The pressure in the secondary air passage can be checked using the GTS.

1.

Start the engine and warm it up.

2.

Turn the ignition switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON.

5.

Turn the GTS on.

6.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN and AIR PUMP: OFF, ASV 1: CLOSE, ASV 2: CLOSE.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.


7.

Start the engine.

8.

Perform the secondary air injection system forced operation while the engine is idling.

9.

Check that the Data List values for the air pump (AIR PUMP), emission control valve (ASV) and pressure in the secondary air injection system passage (PRESSURE) displayed on the GTS are as shown in the table below.

Standard:
GTS Operation Air Pump Emission Control Valve Pressure*1 Pulsation*2
AIR PUMP: ON, ASV: OPEN ON OPEN 1 kPa or higher 15 kPa or higher
AIR PUMP: OFF, ASV: CLOSE OFF CLOSE Below 3 kPa Below 25 kPa


*1: Average pumping pressure (gauge pressure). The pressure should be 1 kPa or higher when the secondary air injection system operates.

*2: The cumulative exhaust pulsation calculated by the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the secondary air injection system.

10.

Turn the ignition switch off.

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



HINT:
·

Bank 1 refers to the bank that includes the NO. 1 cylinder*.

*: The NO. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the NO. 1 cylinder.





PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs and freeze frame data.

Result
Result Proceed to
P2440, P2441, P2442 and/or P2443 is output A
P2440 and/or P2441 and P0412 are output B
P2442 and/or P2443 and P0416 and/or P0417 are output C
P2440, P2441, P2442 and/or P2443 and other DTCs (except P0412, P0416 and P0417) are output D

HINT:

If any DTCs other than P0412, P0416, P0417, P2440, P2441, P2442 and P2443 are output, troubleshoot those DTCs first.




A

2.CHECK FREEZE FRAME DATA (AIR PUMP FREEZE, AIR SWITCHING VALVE FREEZE AND AIR SWITCHING VALVE2 FREEZE)

B

GO TO EMISSION CONTROL VALVE INSPECTION PROCEDURE (P0412)

C

GO TO EMISSION CONTROL VALVE INSPECTION PROCEDURE (P0416 AND P0417)

D

2.CHECK FREEZE FRAME DATA (AIR PUMP FREEZE, AIR SWITCHING VALVE FREEZE AND AIR SWITCHING VALVE2 FREEZE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Read the values of Air Pump Freeze, Air Switching Valve Freeze and Air Switching Valve2 Freeze from the freeze frame data recorded previously.


d.

Referring to the following table, proceed to the appropriate step according to the result of the data reading.

Result
Result Proceed to
Air Pump Freeze Air Switching Valve Freeze Air Switching Valve2 Freeze
OFF OFF OFF B
Except above A



A

3.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR PUMP HEATER)

B

8.INSPECT AIR PUMP ASSEMBLY
3.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR PUMP HEATER)
a.
U180640E01
0.158,0.095 0.339,0.294 0.181,0.200 10 *a 1.608,0.148 1.896,0.310 0.288,0.163 10 A50 1.61,0.963 0.902,0.663 false 0.451,0.49 0.911,0.653 0.460,0.163 10 APH+

Disconnect the air pump connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON and turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT/ Active Test / Activate the Air Pump Heater.


e.

Measure the voltage according to the value(s) in the table below.

:
Tester Connection Condition Specified Condition
A50-1 (APH+) - Body ground Activate the Air Pump Heater is ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Air Pump Assembly)


f.

Reconnect the air pump connector.



OK

4.INSPECT AIR PUMP ASSEMBLY (HEATER RESISTANCE)

NG

5.INSPECT AIR PUMP HEATER RELAY (AIR PUMP HTR)
4.INSPECT AIR PUMP ASSEMBLY (HEATER RESISTANCE)
a.

Inspect the air pump assembly (See page Engine / Hybrid System>1GR-FE EMISSION CONTROL>AIR PUMP>INSPECTION).



OK

5.INSPECT AIR PUMP HEATER RELAY (AIR PUMP HTR)

NG

5.INSPECT AIR PUMP HEATER RELAY (AIR PUMP HTR)
a.

Inspect the air pump heater relay (AIR PUMP HTR) (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION).



OK

6.CHECK AIR PUMP HEATER RELAY (POWER SOURCE)

NG

REPLACE AIR PUMP HEATER RELAY (AIR PUMP HTR)

6.CHECK AIR PUMP HEATER RELAY (POWER SOURCE)
a.

Remove the air pump heater relay (AIR PUMP HTR).


b.
A288678E01
0.899,0.46 1.175,0.633 0.277,0.174 10 *1 1.64,3.093 1.917,3.267 0.277,0.174 10 *2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Air pump heater relay (AIR PUMP HTR) terminal 5 - Body ground Always 11 to 14 V


Text in Illustration
*1 Air Pump Heater Relay (AIR PUMP HTR)
*2 Engine Room Relay Block


c.

Reinstall the air pump heater relay (AIR PUMP HTR).



OK

7.CHECK HARNESS AND CONNECTOR (AIR PUMP - AIR PUMP HEATER RELAY, BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (AIR PUMP - AIR PUMP HEATER RELAY, BODY GROUND)
a.

Remove the air pump heater relay (AIR PUMP HTR).


b.

Disconnect the air pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
Air pump heater relay (AIR PUMP HTR) terminal 3 - A50-1 (APH+) Always Below 1 Ω
A50-3 (APHG) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
Air pump heater relay (AIR PUMP HTR) terminal 3 or A46-1 (APH+) - Body ground Always 10 kΩ or higher



d.

Reinstall the air pump heater relay (AIR PUMP HTR).


e.

Reconnect the air pump connector.



OK

8.INSPECT AIR PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT AIR PUMP ASSEMBLY

OK

9.PERFORM ACTIVE TEST USING GTS (SECONDARY AIR INJECTION SYSTEM OPERATION)

NG

9.PERFORM ACTIVE TEST USING GTS (SECONDARY AIR INJECTION SYSTEM OPERATION)
A221579E01
0.079,0 0.306,0.163 0.228,0.163 10 *A 0.079,2.019 0.281,2.212 0.202,0.193 10 *B

a.

Perform a visual check:

i.

Start the engine and warm it up.


ii.

Turn the ignition switch off.


iii.

Disconnect the air hoses.


iv.

Connect the GTS to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the GTS on.


vii.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



viii.

Start the engine.


ix.

Perform the secondary air injection system forced operation while the engine is idling.


x.

Place your hand near the emission control valve port and check that the exhaust gas pressure pulsates when the emission control valve is turned on.

CAUTION:

To avoid the danger of being burned by the exhaust gas, bring your hand close to the valve port slowly.



xi.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN and AIR PUMP: ON, ASV1: CLOSE, ASV2: CLOSE.


xii.

Check that the exhaust gas does not pulsate when the emission control valve is turned off.


xiii.

Turn the ignition switch off.

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



OK:
Air Pump Operation Emission Control Valve Operation Exhaust Gas Pulsation
ON OFF Not detected
ON ON Detected


Text in Illustration
*A for Bank 1
*B for Bank 2




OK

10.INSPECT NO. 1 EMISSION CONTROL VALVE SET (PRESSURE SENSOR)

NG

11.INSPECT AIR TUBE (BLOCKAGE AND LEAKAGE)
10.INSPECT NO. 1 EMISSION CONTROL VALVE SET (PRESSURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute).


e.

Check the pressure displayed on the GTS.

Standard pressure:

45 to 135 kPa


HINT:

The GTS displays the air pump pressure as absolute pressure.


Result
Result Proceed to
OK A
NG (for Bank 1) B
NG (for Bank 2) C



A

END

B

C

11.INSPECT AIR TUBE (BLOCKAGE AND LEAKAGE)
A288677

a.

Check that the air tubes are securely connected to both the exhaust manifold and the emission control valve.


b.

Inspect the air tube for blockages and damage.

OK:

No blockages in or damage to air tubes.




OK

12.INSPECT NO. 1 EMISSION CONTROL VALVE SET

NG

REPLACE AIR TUBE

12.INSPECT NO. 1 EMISSION CONTROL VALVE SET
a.

b.

Inspect the NO. 2 emission control valve set (See page Engine / Hybrid System>1GR-FE EMISSION CONTROL>AIR SWITCHING VALVE(for Bank 2)>INSPECTION).

Result
Result Proceed to
OK A
NG (for Bank 1) B
NG (for Bank 2) C



A

13.INSPECT AIR INJECTION VSV RELAY (AI-VSV)

B

C

13.INSPECT AIR INJECTION VSV RELAY (AI-VSV)
a.

Inspect the air injection VSV relay (AI-VSV) (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION).



OK

14.CHECK AIR INJECTION VSV RELAY (POWER SOURCE)

NG

REPLACE AIR INJECTION VSV RELAY (AI-VSV)

14.CHECK AIR INJECTION VSV RELAY (POWER SOURCE)
A288679E01
1.264,0.393 1.534,0.590 0.270,0.197 10 *1 1.617,3.075 1.865,3.272 0.249,0.197 10 *2

a.

Remove the air injection VSV relay (AI-VSV).


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Air injection VSV relay (AI-VSV) terminal 1 - Body ground Ignition switch ON 11 to 14 V
Air injection VSV relay (AI-VSV) terminal 5 - Body ground Always 11 to 14 V


Text in Illustration
*1 Air Injection VSV Relay (AI-VSV)
*2 Engine Room Relay Block


c.

Reinstall the air injection VSV relay (AI-VSV).



OK

15.CHECK HARNESS AND CONNECTOR (AIR INJECTION VSV RELAY (AI-VSV) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (AIR INJECTION VSV RELAY (AI-VSV) - ECM)
a.

Remove the air injection VSV relay (AI-VSV).


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Air injection VSV relay (AI-VSV) terminal 2 - B38-21 (AIR1) Always Below 1 Ω
Air injection VSV relay (AI-VSV) terminal 2 or B38-21 (AIR1) - Body ground Always 10 kΩ or higher



d.

Reinstall the air injection VSV relay (AI-VSV).


e.

Reconnect the ECM connector.



OK

16.CHECK HARNESS AND CONNECTOR (NO. 2 EMISSION CONTROL VALVE SET - AIR INJECTION VSV RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (NO. 2 EMISSION CONTROL VALVE SET - AIR INJECTION VSV RELAY)
a.

Disconnect the NO. 2 emission control valve set connector.


b.

Remove the air injection VSV relay (AI-VSV).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B54-5 (+BL) - Air injection VSV relay (AI-VSV) terminal 3 Always Below 1 Ω
B54-1 (GNDL) - Body ground Always Below 1 Ω
B54-5 (+BL) or Air injection VSV relay (AI-VSV) terminal 3 - Body ground Always 10 kΩ or higher



d.

Reconnect the NO. 2 emission control valve set connector.


e.

Reinstall the air injection VSV relay (AI-VSV).



OK

17.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)
U180641E01
1.554,0.284 1.842,0.447 0.288,0.163 10 A48 1.529,2.264 1.817,2.427 0.288,0.163 10 A49 0.617,1.918 1.162,2.095 0.545,0.177 10 BATT 1.408,1.349 0.875,1.869 false 0.94,3.861 1.068,4.038 0.128,0.177 10 E 1.172,3.287 1.015,3.831 false 0.172,0.096 0.376,0.308 0.204,0.211 10 *a

a.

Disconnect the air injection control driver connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-1 (E) - Body ground Always Below 1 Ω



c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A48-1 (BATT) - Body ground Always 11 to 14 V (near battery voltage)



Text in Illustration
*a Front view of wire harness connector
(to Air Injection Control Driver)

e.

Reconnect the air injection control driver connectors.



OK

18.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
a.

Disconnect the ECM connectors.


b.

Disconnect the air injection control driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B36-26 (AIRV) - A49-3 (SIV) Always Below 1 Ω
B36-26 (AIRV) or A49-3 (SIV) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connectors.


e.

Reconnect the air injection control driver connector.



OK

19.PERFORM ACTIVE TEST USING GTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.PERFORM ACTIVE TEST USING GTS
a.
U180678E02
1.375,2.625 1.177,3.115 false 1.542,2.615 1.5,3.094 false 1.688,2.604 1.948,3.083 false 1.844,2.604 2.313,3.094 false 0.635,2.479 0.958,2.677 0.323,0.198 10 false A49 0.99,1.938 1.229,2.115 0.24,0.177 10 false *a 1.115,3.146 1.302,3.323 0.188,0.177 10 false E 1.458,3.135 1.667,3.313 0.208,0.177 10 false DI 1.844,3.125 2.24,3.302 0.396,0.177 10 false SIV 2.292,3.104 2.698,3.281 0.406,0.177 10 false SIP 2.531,0.063 2.771,0.24 0.24,0.177 10 false *2 0.667,0.208 0.906,0.385 0.24,0.177 10 false *1 2.417,0.781 2.854,0.958 0.438,0.177 10 false AIDI 2.417,1.135 2.865,1.313 0.448,0.177 10 false AIRV 0.844,0.792 1.052,0.969 0.208,0.177 10 false DI 0.781,1.156 1.177,1.333 0.396,0.177 10 false SIV

Disconnect the air injection control driver connector.


b.

Connect terminals DI and SIV of the wire harness connector for the air injection control driver.

Text in Illustration
*1 Air Injection Control Driver
*2 ECM
*a Front view of wire harness connector
(to Air Injection Control Driver)


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



f.

Start the engine.


g.

Perform the secondary air injection system forced operation while the engine is idling.


h.

Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is ON and OFF.


i.

Turn the ignition switch off.

NOTICE:
·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
A49-3 (SIV) - A49-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
A49-3 (SIV) - A49-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



j.
U180679E01
0.678,2.442 0.942,2.623 0.264,0.181 10 A49 0.983,1.842 1.219,2.023 0.236,0.181 10 *a 1.432,2.579 1.234,3.068 false 1.589,2.579 1.554,3.06 false 1.157,3.081 1.343,3.262 0.187,0.181 10 E 1.468,3.081 1.678,3.262 0.210,0.181 10 DI 1.732,2.582 1.986,3.064 false 1.842,3.081 2.239,3.262 0.397,0.181 10 SIV 1.881,2.587 2.351,3.068 false 2.266,3.081 2.677,3.262 0.411,0.181 10 SIP 2.534,0.067 2.770,0.248 0.236,0.181 10 *2 0.665,0.209 0.901,0.390 0.236,0.181 10 *1 2.446,0.731 2.892,0.913 0.446,0.181 10 AIDI 2.446,1.084 2.909,1.265 0.463,0.181 10 AIRP 0.867,0.725 1.077,0.907 0.210,0.181 10 DI 0.777,1.087 1.175,1.269 0.397,0.181 10 SIP

Connect terminals DI and SIP of the wire harness connector for the air injection control driver.

Text in Illustration
*1 Air Injection Control Driver
*2 ECM
*a Front view of wire harness connector
(to Air Injection Control Driver)


k.

Connect the GTS to the DLC3.


l.

Turn the ignition switch to ON and turn the GTS on.


m.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



n.

Start the engine.


o.

Perform the secondary air injection system forced operation while the engine is idling.


p.

Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is ON and OFF.


q.

Turn the ignition switch off.

NOTICE:
·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
A49-4 (SIP) - A49-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
A49-4 (SIP) - A49-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



r.

Reconnect the air injection control driver connector.



OK

20.REPLACE AIR INJECTION CONTROL DRIVER

NG

20.REPLACE AIR INJECTION CONTROL DRIVER
a.

Replace the air injection control driver (See page Engine / Hybrid System>1GR-FE EMISSION CONTROL>AIR INJECTION DRIVER>REMOVAL).



NEXT

21.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440, P2441, P2442 AND/OR P2443)
21.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440, P2441, P2442 AND/OR P2443)
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.



g.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.


h.

Start the engine after the GTS initialization is finished.


i.

Perform the System Check operation by pressing ENTER (Next).


j.

Perform the following to confirm the secondary air injection system pending codes: Press the Exit button.


k.

Check for pending DTCs.

OK:

No pending DTC is output.



l.

Turn the ignition switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.





OK

END

NG