After starting the engine, this DTC is stored when the engine stops without the ignition switch being operated.
Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle has ran out of fuel before performing troubleshooting, as this DTC is also stored when the engine stalls due to running out of fuel.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P1603 | After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the ignition switch being operated for 0.5 seconds or more (1 trip detection logic). | ·
Air leak in intake system ·
Purge VSV ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Wire harness or connector ·
Air fuel ratio sensor ·
Power supply circuit (purge VSV, fuel injector assembly, ignition coil assembly) ·
Fuel pump ·
Fuel pump control system ·
Fuel line ·
Throttle body with motor assembly ·
Camshaft timing oil control valve assembly ·
Air conditioning system ·
Power steering system ·
Electrical load signal system ·
A/T system ·
Park/neutral position switch assembly ·
ECM |
This DTC is stored if the engine speed drops below the set speed.
Using the intelligent tester, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
It is necessary to check if the vehicle ran out of fuel before performing troubleshooting, as this DTC is also stored when idling is unstable due to running out of fuel.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P1605 | After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less (1 trip detection logic). | ·
Air leak in intake system ·
Purge VSV ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Wire harness or connector ·
Air fuel ratio sensor ·
Power supply circuit (purge VSV, fuel injector assembly, ignition coil assembly) ·
Fuel pump ·
Fuel pump control system ·
Fuel line ·
Throttle body with motor assembly ·
Camshaft timing oil control valve assembly ·
Knock sensor ·
Ignition coil assembly ·
Fuel injector assembly ·
Spark plug(s) ·
Air conditioning system ·
Power steering system ·
Electrical load signal system ·
A/T system ·
Park/neutral position switch assembly ·
ECM |
In contrast to normal malfunction diagnosis for components, circuits and systems, DTCs P1603 and P1605 are used to determine the malfunctioning area from the problem symptoms and freeze frame data when the user mentions problems such as engine stall.
As these DTCs can be stored as a result of certain user actions, even if these DTCs are output, if the customer makes no mention of problems, clear these DTCs without performing any troubleshooting and return the vehicle to the customer.
If any other DTCs are output, perform troubleshooting for those DTCs first.
Use any information from the customer problem analysis about the condition of the vehicle at the time when the problem occurred (how the engine stopped, conditions when the engine was restarted, etc.) as a reference.
| Symptom | Suspected Area |
|---|---|
| Engine vibration occurs and engine stops | Air-fuel ratio abnormal |
| Engine stops with no engine vibration | Ignition system, injection stoppage, high load from external parts |
| Engine can be started with accelerator pedal depressed | Insufficient air volume |
| Rough idling after engine started | Air-fuel ratio abnormal, abnormal combustion |
Read freeze frame data using the intelligent tester. Freeze frame data records engine conditions when a malfunction occurs. This information can be useful when troubleshooting.
When confirming the freeze frame data, be sure to check all 5 sets of freeze frame data (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
When DTC P1603 (Engine Stall History) is stored, DTC P1605 (Rough Idling) is also stored. When confirming freeze frame data, check DTC P1605. The ECM stores DTC P1605 first. Therefore, 5 sets of freeze frame data can be confirmed through DTC P1605, enabling the technician to obtain more information.
When confirming freeze frame data, if there are multiple items related to the cause of the malfunction, perform troubleshooting for all related items.
Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
Inspections take into account the fact that the malfunction may not have reoccurred and place emphasis on checking the vehicle conditions present at the time when the malfunction occurred.
When performing inspections, jiggle the relevant wire harnesses and connectors in an attempt to reproduce malfunctions that do not always occur.
Using freeze frame data, narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred.
If the engine stalled when the intake air volume was low (during idling or deceleration), there may be a decrease in torque due to an incorrect air-fuel ratio, etc.
If the engine stalled when the intake air volume was high (during driving or acceleration), there may be a major malfunction such as continuous misfire due to ignition stoppage, fuel injection stoppage, etc. and the torque drops to zero.
If the engine speed decreased slowly, there may have been a decrease in torque due to an air-fuel ratio that was incorrect (by approximately 20 to 30%), etc.
If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.
If the air-fuel ratio is abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.
If the vehicle was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.
P1603 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).
| Vehicle State | Engine Speed | Suspected Area | Primary Parts to Inspect | Procedure | |
|---|---|---|---|---|---|
| Idling or decelerating | Slowly decreases and engine stalls | Air-fuel ratio abnormal | Air suction | ·
Intake system connections ·
Purge VSV system |
3 to 4 |
| Sensor malfunction (value from sensor too lean) | ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Air fuel ratio sensor system |
5 to 14 | |||
| Sensor malfunction (value from sensor too rich) | 23 to 32 | ||||
| Fuel supply problem | ·
Fuel pump control system ·
Purge VSV system ·
Fuel line ·
ECM |
15 to 22 | |||
| Intake air volume insufficient | ISC flow rate | ·
Throttle body with motor assembly (ISC valve) |
33 to 35 | ||
| Excessive valve overlap | ·
Camshaft timing oil control valve |
36, 37 | |||
| Ignition timing incorrect | Does not operate as expected | ·
Engine coolant temperature sensor ·
Mass air flow meter |
38 to 40 | ||
| Rapidly decreases and engine stalls | Ignition and injection stops (electrical system malfunction) | Power temporarily cut | ·
Power supply circuit (fuel injector assembly, ignition coil assembly) |
41, 42 | |
| External part malfunctioning | Increase in load | ·
Air conditioning system ·
Electrical load signal system ·
Power steering system ·
A/T system ·
Park/neutral position switch assembly |
45 to 47 | ||
| Accelerating | - | Crankshaft position sensor or VVT sensor malfunction | Power temporarily cut | ·
Check DTCs |
1 |
| Mass air flow meter | Foreign matter adhesion | ·
Mass air flow meter |
48, 49 | ||
| Fuel supply problem | Fuel leak, clog | ·
Fuel pump control system ·
Fuel line |
50, 51 | ||
| Ignition and injection stops (electrical system malfunction) | Power temporarily cut | ·
Power supply circuit (fuel injector assembly, ignition coil assembly) |
52 to 54 | ||
If the engine speed decreased slowly, there may have been a decrease in torque due an air-fuel ratio that was incorrect (by approximately 20 to 30%), etc.
If the engine speed decreased rapidly, there may have been a malfunction such as when the engine misfires almost continuously due to ignition stoppage, fuel injection stoppage, etc., or when the external load increases due to an external part malfunctioning.
If the air-fuel ratio is abnormal, there may have been an intake air leak, sensor malfunction, or fuel supply problem.
If the vehicle was normal, the air volume may have been insufficient or the ignition timing may have been incorrect.
P1605 inspection flow: Narrow down the parts to be inspected according to the vehicle conditions at the time when the malfunction occurred (freeze frame data).
| Engine Speed | Suspected Area | Primary Parts to Inspect | Procedure | |
|---|---|---|---|---|
| Slowly decreases and engine stalls | Air-fuel ratio abnormal | Air suction | ·
Intake system connections ·
Purge VSV system |
3 to 4 |
| Sensor malfunction (value from sensor too lean) | ·
Mass air flow meter ·
Engine coolant temperature sensor ·
Air fuel ratio sensor system |
5 to 14 | ||
| Sensor malfunction (value from sensor too rich) | 23 to 32 | |||
| Fuel supply problem | ·
Fuel pump control system ·
Purge VSV system ·
Fuel line ·
ECM |
15 to 22 | ||
| Intake air volume insufficient | ISC flow rate | ·
Throttle body with motor assembly (ISC valve) |
33 to 35 | |
| Ignition timing incorrect | Does not operate as expected | ·
Knock sensor ·
Engine coolant temperature sensor ·
Mass air flow meter |
38 to 40 | |
| Rapidly decreases and engine stalls | Ignition and injection stops (electrical system malfunction) | Power temporarily cut | ·
Power supply circuit (fuel injector assembly, ignition coil assembly) |
41, 42 |
| External part malfunctioning | Increase in load | ·
Air conditioning system ·
Electrical load signal system ·
Power steering system ·
A/T system ·
Park/neutral position switch assembly |
45 to 47 | |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Read the DTCs (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| Only DTC P1603 and P1605 are output | A |
| DTCs other than P1603 and P1605 are output | B |
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Problem Symptom | Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | ||
|---|---|---|---|---|---|
| Closed Throttle Position SW | Engine Speed | Total of Short FT and Long FT | |||
| When idling or decelerating, engine speed slowly decreases and engine stalls | All 5 sets of freeze frame data are ON | Decreases slowly*1 | All 5 sets of freeze frame data are +15% or more*2 | ·
Air suction ·
Sensor malfunction (value from sensor too lean) ·
Fuel supply problem |
A |
| At least 1 of the 5 sets of freeze frame data is -15% or less*3 | Sensor malfunction (value from sensor too rich) | B | |||
| All 5 sets of freeze frame data are from -15% to +15% | ·
Intake air volume insufficient ·
Ignition timing incorrect |
C | |||
| When idling or decelerating, engine speed rapidly decreases and engine stalls | Decreases rapidly*1 | - | ·
Injection stoppage, ignition stoppage ·
Load from external parts |
D | |
| When accelerating or driving at constant speed, engine stalls*4 | At least one is OFF | - | - | ·
Sensor malfunction ·
Injection stoppage, ignition stoppage ·
Fuel supply problem |
E |
*1: A rapid decrease in engine speed may be caused by an electrical fault in the shared wiring of all or a number of cylinders, an increase in load from external parts, etc. The engine speed is considered to have decreased rapidly if either of the following conditions applies.
Otherwise, the engine speed is considered to have decreased slowly.
In the freeze frame data, the decrease in engine speed from #3 to #5 is 400 rpm or more.
In the freeze frame data, the engine speed at #5 is 120 rpm or less.
If the vehicle speed is 30 km/h or less and the difference between Engine Speed and SPD (NT) is 100 rpm or less, inspect the automatic transmission. (Depending on the rate of vehicle deceleration, the engine speed may have decreased due to the A/T lock-up release being late.)
*2: When a DTC is stored, feedback compensation increases because the air-fuel ratio is determined to be lean.
*3: When a DTC is stored, feedback compensation decreases because the air-fuel ratio is determined to be rich.
*4: This item should be checked when DTC P1603 is output and is not necessary to check when only P1605 is output.
A
B
C
D
E
Check for air leakage in the intake system [vacuum hose disconnection, cracks, damaged gaskets, etc.] (See page Engine / Hybrid System>1GR-FE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).
If the accelerator pedal is released after racing the engine, the inspection is easier to perform because the vacuum inside the intake pipes increases and the air suction noise becomes louder.
If Short FT and Long FT are largely different from the normal values when idling (the intake air volume is small) and almost the same as the normal values when racing the engine (the intake air volume is high), air leakage may be present.
There is no air leakage.
OK
NG
Disconnect the purge hose (on the canister side) of the purge VSV.
Start the engine.
Idle the engine.
Disconnect the connector of the purge VSV.
Check if air flows through the purge VSV.
Air does not flow.
Connect the connector of the purge VSV.
Connect the purge hose of the purge VSV.
When this inspection is performed, the MIL may illuminate. After finishing the inspection, check and clear DTCs (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Calculate Load | Below 90% of the current value of the vehicle*1 | Mass air flow meter | A |
| AFS Voltage B1S1 | 3.3 V or higher*2 | ·
Air fuel ratio sensor ·
Wire harness or connector ·
Actual air-fuel ratio abnormal |
B |
| Both freeze frame data items listed above | Values are other than above | - | C |
Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
*1: If the mass air flow meter is malfunctioning and incorrectly measures the pressure to be less than the actual intake manifold pressure, the freeze frame data will show a low engine load value.
*2: If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is lean, the actual air-fuel ratio will become rich and the engine may stall.
A
B
C
Remove the mass air flow meter.
Check for foreign matter in the airflow passage of the mass air flow meter.
| Result | Proceed to |
|---|---|
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
Install the mass air flow meter.
Even if the results are normal, the mass air flow meter may have been malfunctioning. Continue this inspection procedure until step 22, and if there are no problems with other parts, replace the mass air flow meter (refer to step 55).
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Idle the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
| Tester Display | Specified Condition |
|---|---|
| Control the Injection Volume (25%) | Air fuel ratio sensor output voltage is below 3.1 V |
| Control the Injection Volume (-12.5%) | Air fuel ratio sensor output voltage is higher than 3.4 V |
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
Even if the results are normal, the air fuel ratio sensor may have been malfunctioning. Continue this inspection procedure until step 22, and if there are no problems with other parts, replace the air fuel ratio sensor (refer to step 55).
A
B
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B26-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| B27-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *A | Bank 1 |
| *B | Bank 2 |
| *a | Front view of wire harness connector
(to Air Fuel Ratio Sensor) |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B26-1 (HA1A) - B39-17 (HA1A) | Always | Below 1 Ω |
| B26-3 (A1A+) - B38-1 (A1A+) | Always | Below 1 Ω |
| B26-4 (A1A-) - B38-2 (A1A-) | Always | Below 1 Ω |
| B27-1 (HA2A) - B39-19 (HA2A) | Always | Below 1 Ω |
| B27-3 (A2A+) - B38-7 (A2A+) | Always | Below 1 Ω |
| B27-4 (A2A-) - B38-8 (A2A-) | Always | Below 1 Ω |
| B26-1 (HA1A) or B39-17 (HA1A) - Body ground | Always | 10 kΩ or higher |
| B26-3 (A1A+) or B38-1 (A1A+) - Body ground | Always | 10 kΩ or higher |
| B26-4 (A1A-) or B38-2 (A1A-) - Body ground | Always | 10 kΩ or higher |
| B27-1 (HA2A) or B39-19 (HA2A) - Body ground | Always | 10 kΩ or higher |
| B27-3 (A2A+) or B38-7 (A2A+) - Body ground | Always | 10 kΩ or higher |
| B27-4 (A2A-) or B38-8 (A2A-) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item for DTC P1605 | Result | Proceed to |
|---|---|---|
| Initial Engine Coolant Temp, Ambient Temperature, Initial Intake Air Temp | Difference in temperature between each item is less than 10°C*1 | A |
| Difference in temperature between each item is 10°C or more*2 | B |
*1: A long time had elapsed after stopping the engine.
*2: A long time had not elapsed after stopping the engine.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A | ·
Engine coolant temperature sensor ·
Thermostat |
A |
| Range B | Engine coolant temperature sensor | B | |
| Range C | - | C |
This step is not directly related to engine stall.
A
B
C
For the thermostat inspection, refer to the following procedures (See page Engine / Hybrid System>1GR-FE COOLING>THERMOSTAT>INSPECTION).
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
This step is not directly related to engine stall.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Coolant Temp | 120°C or higher | Engine coolant temperature sensor | A |
| Coolant Temp, Ambient Temperature | Engine coolant temperature is lower than outside temperature by 15°C or more | Engine coolant temperature sensor | |
| Both freeze frame data items listed above | Values are other than above | - | B |
A
B
For the engine coolant temperature sensor inspection, refer to the following procedures (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
Even if the results are normal, the engine coolant temperature sensor may have been malfunctioning. Continue this inspection procedure until step 22, and if there are no problems with other parts, replace the engine coolant temperature sensor (refer to step 55).
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
|---|---|---|---|
| EVAP (Purge) VSV | At least 1 of the 5 sets of freeze frame data is not 0% | Purge VSV | A |
| All 5 sets of freeze frame data are 0% | - | B |
If the purge VSV is stuck closed, air-fuel ratio compensation by the purge VSV is incorrectly adjusted, and then the air-fuel ratio becomes lean and the engine may stall.
A
B
Disconnect the purge hose (on the canister side) of the purge VSV.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.
Operate the purge VSV and check the airflow.
| Activate the VSV for Evap Control | Specified Condition |
|---|---|
| ON | Air flows |
| OFF | Air does not flow |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Even if the results are normal, the purge VSV may have been malfunctioning. Continue this inspection procedure until step 22, and if there are no problems with other parts, replace the purge VSV (refer to step 55).
A
B
Inspect the purge VSV (See page Engine / Hybrid System>1GR-FE EMISSION CONTROL>PURGE VALVE>INSPECTION).
OK
NG
Disconnect the purge VSV connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B15-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Purge VSV) |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Disconnect the purge VSV connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B15-2 - B38-18 (PRG) | Always | Below 1 Ω |
| B15-2 or B38-18 (PRG) - Body ground | Always | 10 kΩ or higher |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump / Speed | Specified Condition |
|---|---|
| ON | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.
If the fuel pump operating noise is abnormal, proceed to step 21.
A
B
Inspect the fuel pump (See page Engine / Hybrid System>1GR-FE FUEL>FUEL PUMP>INSPECTION).
OK
NG
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
| Result | Proceed to |
|---|---|
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
If there is foreign matter such as iron particles on the fuel pump, fuel filter or fuel tank, remove the foreign matter.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Calculate Load | 110% or more of the current value of the vehicle*1 | Mass air flow meter | A |
| AFS Voltage B1S1 | Below 3.3 V*2 | ·
Air fuel ratio sensor ·
Harness and connector ·
Actual air-fuel ratio abnormal |
B |
| Both freeze frame data items listed above | Values are other than above | - | C |
Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
*1: If the mass air flow meter is malfunctioning and incorrectly measures the intake air volume to be higher than the actual volume of air flowing through the intake manifold, the freeze frame data will show a high engine load value.
*2: As the air fuel ratio sensor output is low before the sensor warms up, the value at that time cannot be used for diagnosis. If the air fuel ratio sensor is malfunctioning and constantly outputs a value indicating the air-fuel ratio is rich, the actual air-fuel ratio will become lean and the engine may stall.
A
B
C
Remove the mass air flow meter.
Check for foreign matter in the airflow passage of the mass air flow meter.
| Result | Proceed to |
|---|---|
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
Even if the results are normal, the mass air flow meter may have been malfunctioning. Continue this inspection procedure until step 32, and if there are no problems with other parts, replace the mass air flow meter (refer to step 55).
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Start the engine, turn off all accessory switches and warm up the engine until the engine coolant temperature stabilizes.
Idle the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Read the output voltage from the air fuel ratio sensor when increasing and decreasing the fuel injection volume.
| Tester Display | Specified Condition |
|---|---|
| Control the Injection Volume (25%) | Air fuel ratio sensor output voltage is below 3.1 V |
| Control the Injection Volume (-12.5%) | Air fuel ratio sensor output voltage is higher than 3.4 V |
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
Even if the results are normal, the air fuel ratio sensor may have been malfunctioning. Continue this inspection procedure until step 32, and if there are no problems with other parts, replace the air fuel ratio sensor (refer to step 55).
A
B
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B26-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| B27-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *A | Bank 1 |
| *B | Bank 2 |
| *a | Front view of wire harness connector
(to Air Fuel Ratio Sensor) |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B26-1 (HA1A) - B39-17 (HA1A) | Always | Below 1 Ω |
| B26-3 (A1A+) - B38-1 (A1A+) | Always | Below 1 Ω |
| B26-4 (A1A-) - B38-2 (A1A-) | Always | Below 1 Ω |
| B27-1 (HA2A) - B39-19 (HA2A) | Always | Below 1 Ω |
| B27-3 (A2A+) - B38-7 (A2A+) | Always | Below 1 Ω |
| B27-4 (A2A-) - B38-8 (A2A-) | Always | Below 1 Ω |
| B26-1 (HA1A) or B39-17 (HA1A) - Body ground | Always | 10 kΩ or higher |
| B26-3 (A1A+) or B38-1 (A1A+) - Body ground | Always | 10 kΩ or higher |
| B26-4 (A1A-) or B38-2 (A1A-) - Body ground | Always | 10 kΩ or higher |
| B27-1 (HA2A) or B39-19 (HA2A) - Body ground | Always | 10 kΩ or higher |
| B27-3 (A2A+) or B38-7 (A2A+) - Body ground | Always | 10 kΩ or higher |
| B27-4 (A2A-) or B38-8 (A2A-) - Body ground | Always | 10 kΩ or higher |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item for DTC P1605 | Result | Proceed to |
|---|---|---|
| Initial Engine Coolant Temp, Ambient Temperature, Initial Intake Air Temp | Difference in temperature between each item is less than 10°C*1 | A |
| Difference in temperature between each item is 10°C or more*2 | B |
*1: A long time had elapsed after stopping the engine.
*2: A long time had not elapsed after stopping the engine.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions present when the DTC was stored which are recorded in the freeze frame data.
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A | ·
Engine coolant temperature sensor ·
Thermostat |
A |
| Range B | Engine coolant temperature | B | |
| Range C | - | C |
This step is not directly related to engine stall.
A
B
C
For the thermostat inspection, refer to the following procedures (See page Engine / Hybrid System>1GR-FE COOLING>THERMOSTAT>INSPECTION).
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
This step is not directly related to engine stall.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Coolant Temp | 120°C or higher | Engine coolant temperature sensor | A |
| Coolant Temp, Ambient Temperature | Engine coolant temperature is lower than outside temperature by 15°C or more | Engine coolant temperature sensor | |
| Both freeze frame data items listed above | Values are other than above | - | B |
A
B
For the engine coolant temperature sensor inspection, refer to the following procedures (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
Even if the results are normal, the engine coolant temperature sensor may have been malfunctioning. If there are no problems with other parts, replace the engine coolant temperature sensor (refer to step 55).
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item for DTC P1605 | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Total of ISC Learning Value and ISC Feedback Value | Below 80% of the current value of the vehicle*1 | Throttle body with motor assembly | A |
| 120% or more of the current value of the vehicle*2 | B | ||
| From 80 to 120% of the current value of the vehicle | - | C |
Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
*1: If the throttle body with motor assembly has a temporary problem in which it cannot fully close, the intake air volume and engine speed increase. As a result, the ISC compensation amount becomes less than the standard. At this time, if the throttle body with motor assembly returns to normal and fully closes, the intake air volume will be insufficient and the engine may stall.
*2: If carbon accumulates on the throttle body with motor assembly and the intake air volume decreases, the ISC compensation amount is increased to maintain the idling speed. If this situation continues, the ISC compensation amount reaches the upper limit, the idling speed cannot be maintained causing idling to become unstable, and the engine may stall.
A
B
C
Check for foreign matter and signs that the throttle body with motor assembly was stuck, and also check that the valve and shaft move smoothly during operation.
| Result | Proceed to |
|---|---|
| Abnormal | A |
| Normal | B |
Even if the results are normal, the throttle body with motor assembly may have been malfunctioning. Continue this inspection procedure until step 40, and if there are no problems with other parts, replace the throttle body with motor assembly (refer to step 55).
A
B
Check if carbon is in the airflow passage of the throttle body.
| Result | Proceed to |
|---|---|
| Carbon in passage | A |
| No carbon in passage | B |
Even if the results are normal, the throttle body with motor assembly may have been malfunctioning. Continue this inspection procedure until step 40, and if there are no problems with other parts, replace the throttle body with motor assembly (refer to step 55).
A
B
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT System (Bank 1) or Control the VVT System (Bank 2).
When performing the Active Test, make sure the A/C is on and the shift lever is in P or N.
Check the engine speed while operating the camshaft timing oil control valve using the intelligent tester.
| Tester Operation | Specified Condition |
|---|---|
| OFF | Normal engine speed |
| ON | Soon after camshaft timing oil control valve switched from OFF to ON, engine idles roughly or stalls |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
If the camshaft timing oil control valve is stuck ON, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the intelligent tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank1) or Control the VVT Exhaust Linear (Bank2).
When performing the Active Test, make sure the A/C is on and the shift lever is in P or N.
Check the engine speed while operating the camshaft timing oil control valve using the intelligent tester.
| Tester Operation | Specified Condition |
|---|---|
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
When the results of the inspection using the Active Test are normal but the valve operating noise is abnormal, check the valve for any signs of problems.
If the camshaft timing oil control valve is stuck ON, the valve overlap increases and combustion worsens due to the internal EGR which may cause rough idle or cause the engine to stall.
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | |
|---|---|---|---|
| IGN Advance | Knock Correct Learn Value | ||
| Differs from the current value of the vehicle by 10° or more | Less than 3° | ·
Engine coolant temperature sensor ·
Mass air flow meter ·
Knock sensor |
A |
| 3° or more | - | B | |
| Differs from the current value of the vehicle by less than 10° | - | - | |
Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
Even if the results are normal, the knock sensors may have been malfunctioning. If there are no problems with other parts, replace the knock sensors (refer to step 55).
A
B
For the engine coolant temperature sensor inspection, refer to the following procedures (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>ENGINE COOLANT TEMPERATURE SENSOR>INSPECTION).
OK
NG
Remove the mass air flow meter.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (THA) - 2 (E2) | 20°C | 2.21 to 2.69 kΩ |
| *a | Component without harness connected
(Mass Air Flow Meter) |
If the intake air temperature sent to the ECM is higher than the standard due to the mass air flow meter (intake air temperature sensor) malfunctioning, the ignition timing may become delayed.
OK
NG
Disconnect the fuel injector assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
|---|---|---|---|
| No. 1 | B1-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 2 | B2-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 3 | B3-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 4 | B4-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 5 | B5-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 6 | B6-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Fuel Injector Assembly) |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)
OK
NG
Disconnect the ignition coil assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B7-1 (+B) - B7-4 (GND) | Ignition switch ON | 11 to 14 V |
| B8-1 (+B) - B8-4 (GND) | Ignition switch ON | 11 to 14 V |
| B9-1 (+B) - B9-4 (GND) | Ignition switch ON | 11 to 14 V |
| B10-1 (+B) - B10-4 (GND) | Ignition switch ON | 11 to 14 V |
| B11-1 (+B) - B11-4 (GND) | Ignition switch ON | 11 to 14 V |
| B12-1 (+B) - B12-4 (GND) | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Ignition Coil Assembly) |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Idle Spark Advn Ctrl (#1 to #6) | At least one cylinder shows a value of 4° or more | ·
Fuel injector system ·
Ignition coil system |
A |
| All cylinders show a value of less than 4° | - | B |
A
B
Change the location of the ignition coil for the cylinder whose Idle Spark Advn Ctrl (#1 to #6) was 4° or more in step 43.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Idle Spark Advn Ctrl (#1 to #6).
| Result | Proceed to |
|---|---|
| Same as result in step 43 | A |
| Different from result in step 43 | B |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
A
B
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | ||
|---|---|---|---|---|
| A/C Signal | Air Conditioner FB Val | Power Steering Signal | ||
| A/C Signal display changes from OFF to ON*1 | Value displayed for Air Conditioner FB Val increases | Does not change from OFF | A/C system | A |
| Changes from OFF to ON | Power steering system | B | ||
| A/C Signal display does not change from OFF | Value displayed for Air Conditioner FB Val does not increase | Changes from OFF to ON | ||
| Does not change from OFF | - | |||
Try to operate the vehicle under the conditions recorded in the freeze frame data which were present when the malfunction occurred. Confirm the data at this time and the data when the engine is idling (engine warmed up, no load, and shift lever in D or N) and compare these data with the freeze frame data.
*1: Check not only the on/off state of the air conditioner, but also the change in air conditioner load.
The normal value for the ISC learned value is engine displacement (liters) x 0.9.
Even if the results are normal, the power steering system may have been malfunctioning. Continue this inspection procedure until step 47, and if there are no problems with other parts, inspect the power steering system (refer to step 55).
B
A
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | |||
|---|---|---|---|---|---|
| Electrical Load Signal or Electric Load Feedback Val | Electric Load Feedback Val | Difference between Engine Speed and Turbine Speed | Vehicle Speed | ||
| Electrical Load Signal display changes from OFF to ON*1, or value displayed for Electric Load Feedback Val increases*1 | Value displayed for Electric Load Val changes | - | - | Electrical load signal circuit | A |
| Value displayed for Electric Load Val does not change | At least 1 of the 5 sets of freeze frame data is less than 100 rpm | Less than 30 km/h | A/T system | B | |
| 30 km/h or more | - | C | |||
| All 5 sets of freeze frame data are 100 rpm or more | - | - | C | ||
| Electrical Load Signal display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase | - | At least 1 of the 5 sets of freeze frame data is less than 100 rpm | Less than 30 km/h | A/T system | B |
| 30 km/h or more | - | C | |||
| All 5 sets of freeze frame data are 100 rpm or more | - | - | C | ||
*1: If the Electrical Load Signal display changes from OFF to ON, or the "Electric Load Feedback Val" increases, it probably is a malfunction due to a change in electrical load. Check the generator and the continuity and connections between the generator and ECM.
The normal value for the ISC learned value is engine displacement (liters) x 0.9.
Even if the results are normal, the electrical load signal system and/or A/T system may have been malfunctioning. Continue this inspection procedure until step 47, and if there are no problems with other parts, inspect the electrical load system and/or A/T system (refer to step 55).
A
B
C
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item for DTC P1605 | Suspected Area | Proceed to | |
|---|---|---|---|
| P Position or N Position | Park/Neutral Position Switch | ||
| P and N position are both OFF in at least one data set | In D or R, NSW is ON | Park/neutral position switch assembly | A |
| In D or R, NSW is OFF | A/T system | B | |
| All 5 sets of freeze frame data are ON | - | - | C |
Even if the results are normal, the park/neutral position switch assembly and/or A/T system may have been malfunctioning. If there are no problems with other parts, inspect the park/neutral position switch assembly and/or A/T system (refer to step 55).
A
B
C
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the intelligent tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>FREEZE FRAME DATA).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
|---|---|---|---|
| Throttle Sensor Position, Calculate Load | Calculate Load decreases while Throttle Sensor Position increases | Mass air flow meter | A |
| Calculate Load does not decrease while Throttle Sensor Position increases | - | B |
A
B
Remove the mass air flow meter.
Check for foreign matter in the air flow passage of the mass air flow meter.
| Result | Proceed to |
|---|---|
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
Install the mass air flow meter.
Even if the results are normal, the mass airflow meter may have been malfunctioning. Continue this inspection procedure until step 54, and if there are no problems with other parts, replace the mass air flow meter (refer to step 55).
A
B
Disconnect the fuel injector assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Cylinder | Tester Connection | Switch Condition | Specified Condition |
|---|---|---|---|
| No. 1 | B1-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 2 | B2-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 3 | B3-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 4 | B4-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 5 | B5-1 - Body ground | Ignition switch ON | 11 to 14 V |
| No. 6 | B6-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Fuel Injector Assembly) |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)
OK
NG
Disconnect the ignition coil assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| B7-1 (+B) - B7-4 (GND) | Ignition switch ON | 11 to 14 V |
| B8-1 (+B) - B8-4 (GND) | Ignition switch ON | 11 to 14 V |
| B9-1 (+B) - B9-4 (GND) | Ignition switch ON | 11 to 14 V |
| B10-1 (+B) - B10-4 (GND) | Ignition switch ON | 11 to 14 V |
| B11-1 (+B) - B11-4 (GND) | Ignition switch ON | 11 to 14 V |
| B12-1 (+B) - B12-4 (GND) | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Ignition Coil Assembly) |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
Make sure there is not an excessive amount of force applied to the wire harness.
A rapid decrease in engine speed may have been caused by a malfunction in all or multiple cylinders. (There may be an electrical malfunction in the wiring shared by all the cylinders.)
OK
NG
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump / Speed | Specified Condition |
|---|---|
| ON | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
Jiggle the wire harness and connector to increase the likelihood of detecting malfunctions that do not always occur.
While performing the Active Test, make sure that there is no fuel leakage from the pipes, no signs that fuel has leaked, and no fuel smell.
If the fuel pump operating noise is abnormal, proceed to step 53.
A
B
Inspect the fuel pump (See page Engine / Hybrid System>1GR-FE FUEL>FUEL PUMP>INSPECTION).
OK
NG
Check for foreign matter such as iron particles around the fuel pump (fuel pump, fuel pump filter and inside the fuel tank), and for signs that the fuel pump was stuck.
| Result | Proceed to |
|---|---|
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
A
B
If the malfunction could not be identified in steps 3 to 22, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Part to Replace |
|---|---|
| Step 6 | Mass air flow meter |
| Step 7 | Air fuel ratio sensor |
| Step 14 | Engine coolant temperature sensor |
| Step 16 | Purge VSV |
| Step 22 | Fuel pump |
If the malfunction could not be identified in steps 23 to 32, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Part to Replace |
|---|---|
| Step 24 | Mass air flow meter |
| Step 25 | Air fuel ratio sensor |
| Step 32 | Engine coolant temperature sensor |
If the malfunction could not be identified in steps 33 to 40, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Part to Replace |
|---|---|
| Step 34, 35 | Throttle body with motor assembly |
| Step 38 | Knock sensor |
If the malfunction could not be identified in steps 41 to 47, inspect and repair the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection |
|---|---|
| Step 45 | A/C system inspection and repair
Power steering system inspection and repair |
| Step 46 | A/T system inspection and repair
Electrical load system inspection and repair |
| Step 47 | Park/neutral position switch assembly inspection and repair
A/T system inspection and repair |
If the malfunction could not be identified in steps 48 to 54, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Part to Replace |
|---|---|
| Step 49 | Mass air flow meter |
Referring to the chart, inspect and repair or replace the part from the step where an inspection was performed.
NEXT
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Clear the DTCs (See page Engine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR).
NEXT
Check if engine stall symptoms are present.
If any engine stall symptoms are present, recheck for DTCs and freeze frame data and perform an inspection.
OK
NG