Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › CAMSHAFT › 2009.08–2013.08
RM1440E _51 Engine / Hybrid System _056125 1GR-FE ENGINE MECHANICAL _0273879 CAMSHAFT A

1GR-FE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


PROCEDURE

Hide 13050 1.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 2.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13050 3.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

a.

Fix the camshaft in place.

NOTICE:

Be careful not to damage the camshaft.



b.
A229667E09
2.208,1.833 2.094,1.833 2.094,1.833 1.885,1.469 false 1.604,0.438 1.375,0.438 1.375,0.438 0.896,1.26 true 2.24,1.75 2.417,1.927 0.177,0.177 10 false *2 1.635,0.344 1.823,0.521 0.188,0.177 10 false *1

Put the camshaft timing gear assembly and camshaft together by aligning the pin hole and straight pin.

Text in Illustration
*1 Pin Hole
*2 Straight Pin


c.

Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.

NOTICE:

Be sure not to turn the camshaft timing gear assembly in the retard direction.



d.

Check that there is no clearance between the camshaft timing gear assembly flange and camshaft.


e.
A229666

Install the flange bolt while holding the camshaft.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


f.

Check the lock of the camshaft timing gear assembly.

i.

Fix the camshaft in place and confirm that the camshaft timing gear assembly is locked.

NOTICE:

Be careful not to damage the camshaft.




Hide 13070A 4.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Fix the camshaft in place.

NOTICE:

Be careful not to damage the camshaft.



b.
A227956E04
1.073,0.917 0.76,0.188 0.76,0.188 0.625,0.188 true 1.292,0.927 1.708,0.208 1.708,0.208 1.854,0.208 true 1.906,0.135 2.083,0.313 0.177,0.177 10 false *2 0.438,0.115 0.625,0.292 0.188,0.177 10 false *1

Put the camshaft timing exhaust gear assembly and camshaft together by aligning the pin hole and straight pin.

Text in Illustration
*1 Pin Hole
*2 Straight Pin


c.

Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.

NOTICE:

Be sure not to turn the camshaft timing exhaust gear in the advanced direction.



d.

Check that there is no clearance between the gear flange and camshaft.


e.
A229668

Install the flange bolt while holding the camshaft.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


f.

Check the camshaft timing exhaust gear lock.

i.

Make sure that the camshaft timing exhaust gear assembly locks.



Hide 13053 5.INSTALL NO. 3 CAMSHAFT

a.
A072945

Check that the notch is aligned with the "0" timing mark of the timing chain cover.


b.
A227954E11
2.458,1.594 2.458,1.531 2.458,1.531 2.49,1.417 true 2.292,0.802 2.417,0.802 2.417,0.802 2.542,1.156 true 1.021,1.073 0.781,1.385 0.781,1.385 1.135,1.146 true 2.396,1.604 2.563,1.771 0.167,0.167 10 true *1 2.104,0.76 2.271,0.927 0.167,0.167 10 true *2 0.719,1.385 0.896,1.573 0.177,0.188 10 true *a

Align the mark plate (yellow) with the timing mark of the camshaft timing gear as shown in the illustration and install the No. 2 chain to the camshaft timing gear.

Text in Illustration
*1 Timing Mark
*2 Mark Plate (yellow)
*a Align


c.

Clean the camshaft housing LH and camshaft journals and apply engine oil to them.


d.
A221097E12
2.042,0.24 1.844,0.24 1.844,0.24 1.698,0.469 false 1.115,1.063 0.635,1.063 false 1.146,1.896 1.406,1.896 1.406,1.896 2.052,0.875 true 2.177,0.833 2.646,0.833 false 2.125,0.167 2.292,0.333 0.167,0.167 10 false *1 0.438,0.979 0.604,1.146 0.167,0.167 10 false *2 0.948,1.813 1.115,1.979 0.167,0.167 10 false *3 2.677,0.771 2.844,0.938 0.167,0.167 10 false *4

Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.

Text in Illustration
*1 Valve Rocker Arm
*2 Lash Adjuster
*3 Valve Stem
*4 Valve Stem Cap


e.
A149856E08
2.583,0.531 1.958,0.531 1.958,0.531 1.458,1.063 true 2.635,0.438 2.979,0.677 0.344,0.24 10 true *a

Install the chain to the No. 3 camshaft, and then install the camshaft to the camshaft housing LH.

Text in Illustration
*a Place on camshaft timing gear

HINT:
·

Place the chain on the camshaft timing gear but do not engage the teeth of the sprocket and the chain.

·

Install the camshaft so that the timing mark is facing upward.




Hide 13054 6.INSTALL NO. 4 CAMSHAFT

a.

Clean the camshaft housing LH and camshaft journals and apply engine oil to them.


b.
A225427E05
2.854,1.948 2.771,1.948 2.771,1.948 2.625,2.26 true 3.042,3.969 2.917,3.969 2.917,3.969 2.427,3.51 true 2.896,1.865 3.063,2.042 0.167,0.177 10 false *1 3.083,3.885 3.25,4.063 0.167,0.177 10 false *2

Pass the No. 4 camshaft through the No. 2 chain from the front of the vehicle, align the mark plate (yellow) with the timing mark and install the No. 2 chain to the camshaft timing exhaust gear.

Text in Illustration
*1 Mark Plate (yellow)
*2 Timing Mark


c.
A224770

While lifting up the No. 4 camshaft, pass the No. 3 chain tensioner assembly through the No. 2 chain and set it in place.


d.

Install the No. 4 camshaft to the camshaft housing LH, and then install the No. 3 chain tensioner assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 7.INSTALL CAMSHAFT BEARING CAP (for Bank 2)

a.

Clean the camshaft bearing caps and apply engine oil to them.


b.
A221097E12
2.042,0.24 1.844,0.24 1.844,0.24 1.698,0.469 false 1.115,1.063 0.635,1.063 false 1.146,1.896 1.406,1.896 1.406,1.896 2.052,0.875 true 2.177,0.833 2.646,0.833 false 2.125,0.167 2.292,0.333 0.167,0.167 10 false *1 0.438,0.979 0.604,1.146 0.167,0.167 10 false *2 0.948,1.813 1.115,1.979 0.167,0.167 10 false *3 2.677,0.771 2.844,0.938 0.167,0.167 10 false *4

Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.

Text in Illustration
*1 Valve Rocker Arm
*2 Lash Adjuster
*3 Valve Stem
*4 Valve Stem Cap


c.
A388750E01
2.615,1.458 2.781,1.25 2.781,1.25 2.885,1.25 false 2.438,1.677 2.604,1.677 2.604,1.677 2.604,1.792 false 2.323,1.792 2.729,1.792 false 2.938,1.167 3.198,1.354 0.26,0.188 10 false *1 2.781,1.708 3.042,1.896 0.26,0.188 10 false *2 2.292,3.865 2.521,4.021 0.229,0.156 10 false 1 2.604,2.635 2.865,2.823 0.26,0.188 10 false 2 2.594,2.875 2.854,3.063 0.26,0.188 10 false 3 2.375,2.24 2.635,2.427 0.26,0.188 10 false 4 2.302,4.115 2.563,4.302 0.26,0.188 10 false 5 2.594,3.365 2.854,3.552 0.26,0.188 10 false 6 1.573,3.833 1.833,4.021 0.26,0.188 10 false 7 1.271,2.646 1.531,2.833 0.26,0.188 10 false 8 1.271,2.885 1.531,3.073 0.26,0.188 10 false 9 1.5,2.229 1.76,2.417 0.26,0.188 10 false 10 1.531,4.083 1.76,4.24 0.229,0.156 10 false 11 1.26,3.354 1.49,3.51 0.229,0.156 10 false 12 3.156,3.802 3.375,3.958 0.219,0.156 10 false 13 3.177,2.656 3.396,2.813 0.219,0.156 10 false 14 3.177,2.896 3.396,3.052 0.219,0.156 10 false 15 2.865,2.208 3.083,2.365 0.219,0.156 10 false 16 2.896,3.802 3.115,3.958 0.219,0.156 10 false 17 3.198,3.281 3.417,3.438 0.219,0.156 10 false 18 0.49,2.677 0.708,2.833 0.219,0.156 10 false 19 0.25,2.677 0.469,2.833 0.219,0.156 10 false 20 0.802,2.177 1.021,2.333 0.219,0.156 10 false 21 0.708,3.865 0.927,4.021 0.219,0.156 10 false 22 0.958,3.875 1.177,4.031 0.219,0.156 10 false 23 0.49,3.281 0.708,3.438 0.219,0.156 10 false 24 0.563,4.135 0.781,4.292 0.219,0.156 10 false *a 0.563,4.406 0.781,4.563 0.219,0.156 10 false *b

Check the marks and numbers on the camshaft bearing caps, and then remove the replacement bolts and washers in the order shown in the illustration. Immediately after removing the replacement bolts and washers in the location for a bearing cap, install the bearing cap with the bolts in the order shown in the illustration.

Torque:
for bolt A : 28 N*m (286 kgf*cm, 21 ft.*lbf)
for bolt B : 16 N*m (163 kgf*cm, 12 ft.*lbf)

Text in Illustration
*1 Bolt
*2 Washer
*a Replacement Bolts and Washers Removal
*b Part Installation
V100135

Bolt A
V100136

Bolt B

NOTICE:
·

Be sure to follow the numerical order when performing this procedure.

·

Do not drop replacement bolts and washers into the cylinder head.




d.

Check the torque of each bolt again.


Hide 13506 8.CONNECT CHAIN SUB-ASSEMBLY (for Bank 2)

a.
A225424E03
0.438,2.896 0.573,2.896 0.573,2.896 0.917,3.365 true 0.229,2.813 0.406,3 0.177,0.188 10 false *1

Align the paint marks on the camshaft timing gear and No. 1 chain and install the No. 1 chain to the camshaft timing gear.

Text in Illustration
*1 Paint Mark

HINT:

If the paint marks are not aligned, align them by turning the camshaft slightly.



Hide 13511 9.INSTALL CAMSHAFT

a.
U149640E04
1.094,1.781 1.417,1.781 1.417,1.781 1.563,2.031 true 0.5,1.708 1.083,1.885 0.583,0.177 10 true 5° to 10°

Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain can be installed easily.

HINT:

When turning the crankshaft, engine oil may spray out of the oil holes.



b.
A227955E10
0.927,1.292 0.927,1.135 0.927,1.135 0.667,0.99 true 0.823,0.365 0.688,0.365 0.688,0.365 0.542,0.75 true 2.031,1.094 1.531,1.646 1.531,1.646 2.219,1.146 true 0.854,1.313 1.052,1.469 0.198,0.156 10 false *1 0.865,0.26 1.073,0.448 0.208,0.188 10 true *2 1.385,1.615 1.573,1.802 0.188,0.188 10 false *a

Align the mark plate (yellow) with the timing mark of the camshaft timing gear as shown in the illustration and install the No. 2 chain to the camshaft timing gear.

Text in Illustration
*1 Timing Mark
*2 Mark Plate (yellow)
*a Align


c.

Clean the camshaft housing RH and camshaft journals and apply engine oil to them.


d.
A221097E12
2.042,0.24 1.844,0.24 1.844,0.24 1.698,0.469 false 1.115,1.063 0.635,1.063 false 1.146,1.896 1.406,1.896 1.406,1.896 2.052,0.875 true 2.177,0.833 2.646,0.833 false 2.125,0.167 2.292,0.333 0.167,0.167 10 false *1 0.438,0.979 0.604,1.146 0.167,0.167 10 false *2 0.948,1.813 1.115,1.979 0.167,0.167 10 false *3 2.677,0.771 2.844,0.938 0.167,0.167 10 false *4

Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.

Text in Illustration
*1 Valve Rocker Arm
*2 Lash Adjuster
*3 Valve Stem
*4 Valve Stem Cap


e.
A225421E08
0.781,0.583 1.042,0.583 1.042,0.583 1.302,1.052 true 0.604,0.49 0.792,0.677 0.188,0.188 10 false *a

Install the chain to the camshaft, and then install the camshaft to the camshaft housing RH.

Text in Illustration
*a Place on camshaft timing gear

HINT:
·

Place the chain on the camshaft timing gear but do not engage the teeth of the sprocket and the chain.

·

Install the camshaft so that the timing mark is facing upward.




Hide 13512 10.INSTALL NO. 2 CAMSHAFT

a.

Clean the camshaft housing RH and camshaft journals and apply engine oil to them.


b.
A225428E06
0.875,2.198 0.781,2.198 0.781,2.198 0.729,2.531 true 0.458,3.958 0.604,3.958 0.604,3.958 1.01,3.625 true 0.896,2.125 1.063,2.302 0.167,0.177 10 true *1 0.271,3.885 0.458,4.052 0.188,0.167 10 false *2

Pass the No. 2 camshaft through the No. 2 chain from the front of the vehicle, align the mark plate (yellow) with the timing mark and install the No. 2 chain to the camshaft timing exhaust gear.

Text in Illustration
*1 Mark Plate (yellow)
*2 Timing Mark


c.
A224769

While lifting up the No. 2 camshaft, pass the No. 2 chain tensioner assembly through the No. 2 chain and set it in place.


d.

Install the No. 2 camshaft to the camshaft housing RH, and then install the No. 2 chain tensioner assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 11.INSTALL CAMSHAFT BEARING CAP (for Bank 1)

a.

Clean the camshaft bearing caps and apply engine oil to them.


b.
A221097E12
2.042,0.24 1.844,0.24 1.844,0.24 1.698,0.469 false 1.115,1.063 0.635,1.063 false 1.146,1.896 1.406,1.896 1.406,1.896 2.052,0.875 true 2.177,0.833 2.646,0.833 false 2.125,0.167 2.292,0.333 0.167,0.167 10 false *1 0.438,0.979 0.604,1.146 0.167,0.167 10 false *2 0.948,1.813 1.115,1.979 0.167,0.167 10 false *3 2.677,0.771 2.844,0.938 0.167,0.167 10 false *4

Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.

Text in Illustration
*1 Valve Rocker Arm
*2 Lash Adjuster
*3 Valve Stem
*4 Valve Stem Cap


c.
A388751E01
0.354,1.25 0.5,1.25 0.5,1.25 0.667,1.458 false 0.729,1.792 0.729,1.677 0.729,1.677 0.865,1.677 false 0.438,1.792 0.948,1.792 false 0.156,1.146 0.406,1.344 0.25,0.198 10 false *1 0.26,1.719 0.51,1.917 0.25,0.198 10 false *2 0.563,4.052 0.813,4.25 0.25,0.198 10 false *a 0.563,4.344 0.813,4.542 0.25,0.198 10 false *b 1.177,3.802 1.427,4 0.25,0.198 10 false 1 0.99,2.563 1.24,2.76 0.25,0.198 10 false 2 1,2.802 1.25,3 0.25,0.198 10 false 3 1.25,2.125 1.5,2.323 0.25,0.198 10 false 4 1.188,4.052 1.438,4.25 0.25,0.198 10 false 5 0.99,3.281 1.24,3.479 0.25,0.198 10 false 6 2.115,3.823 2.365,4.021 0.25,0.198 10 false 7 2.385,2.573 2.635,2.771 0.25,0.198 10 false 8 2.385,2.823 2.635,3.021 0.25,0.198 10 false 9 2.24,2.156 2.49,2.354 0.25,0.198 10 false 10 2.063,4.073 2.313,4.271 0.25,0.198 10 false 11 2.333,3.313 2.583,3.51 0.25,0.198 10 false 12 0.365,3.708 0.615,3.906 0.25,0.198 10 false 13 0.292,2.656 0.542,2.854 0.25,0.198 10 false 14 0.063,2.667 0.313,2.865 0.25,0.198 10 false 15 0.375,2.208 0.625,2.406 0.25,0.198 10 false 16 0.115,3.719 0.365,3.917 0.25,0.198 10 false 17 0.292,3.271 0.542,3.469 0.25,0.198 10 false 18 2.958,2.646 3.208,2.844 0.25,0.198 10 false 19 3.198,2.646 3.427,2.854 0.229,0.208 10 false 20 2.917,2.146 3.167,2.344 0.25,0.198 10 false 21 2.833,3.781 3.083,3.979 0.25,0.198 10 false 22 2.833,4.021 3.083,4.219 0.25,0.198 10 false 23 2.979,3.198 3.229,3.396 0.25,0.198 10 false 24

Check the marks and numbers on the camshaft bearing caps, and then remove the replacement bolts and washers in the order shown in the illustration. Immediately after removing the replacement bolts and washers in the location for a bearing cap, install the bearing cap with the bolts in the order shown in the illustration.

Torque:
for bolt A : 28 N*m (286 kgf*cm, 21 ft.*lbf)
for bolt B : 16 N*m (163 kgf*cm, 12 ft.*lbf)

Text in Illustration
*1 Bolt
*2 Washer
*a Replacement Bolts and Washers Removal
*b Part Installation
V100135

Bolt A
V100136

Bolt B

NOTICE:
·

Be sure to follow the numerical order when performing this procedure.

·

Do not drop replacement bolts and washers into the cylinder head.




d.

Check the torque of each bolt again.


Hide 13506 12.CONNECT CHAIN SUB-ASSEMBLY (for Bank 1)

a.
A225425E03
2.99,3.156 2.844,3.156 2.844,3.156 2.323,3.5 true 3.021,3.063 3.208,3.25 0.188,0.188 10 false *1

Align the paint marks on the camshaft timing gear and No. 1 chain and install the No. 1 chain to the camshaft timing gear.

Text in Illustration
*1 Paint Mark

HINT:

If the paint marks are not aligned, align them by turning the camshaft slightly.



Hide 13540 13.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A226509E11
2.76,0.198 3.052,0.458 0.292,0.26 10 true 30° 3.115,0.875 3.313,1.052 0.198,0.177 10 false 0°

Turn the crankshaft counterclockwise 30° past the "0" timing mark, and then turn it clockwise to align the notch with the "0" timing mark.


b.

Turn the crankshaft slightly to eliminate the slack in the chain.

HINT:

Make sure there is some slack in the chain around the area where the chain tensioner is installed.



c.
A178214E17
0.49,1.75 0.688,1.75 0.688,1.75 0.927,1.156 true 2.542,1.052 2.896,1.51 2.896,1.51 2.896,1.667 true 0.292,1.677 0.479,1.885 0.188,0.208 10 false *1 2.031,1.719 2.25,1.938 0.219,0.219 10 false *a 2.823,1.698 3.01,1.906 0.188,0.208 10 false *1

While turning the stopper plate of the tensioner clockwise, push in the plunger of the tensioner as shown in the illustration.

Text in Illustration
*1 Stopper Plate
*a Push


d.

While turning the stopper plate of the tensioner counterclockwise, insert a pin of φ1.27 mm (0.0500 in.) into the holes in the stopper plate and tensioner to fix the stopper plate in place.


e.

Install the chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.

Remove the pin from the No. 1 chain tensioner.


Hide 14.INSPECT VALVE TIMING

a.

Check the camshaft timing marks.

NOTICE:
·

Check each timing mark from a viewpoint directly in line with the center of the camshaft and the timing mark on each camshaft timing gear.

·

If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.




b.

Check that each camshaft timing mark is positioned as shown in the illustration.

A224753E07
1.531,0.49 0.802,0.417 0.802,0.417 1.51,0.813 true 5.854,2.406 6.604,2.26 6.604,2.26 5.885,2.656 true 4.604,0.615 3.854,0.573 3.854,0.573 4.573,0.969 true 2.052,2.563 2.792,2.417 2.792,2.417 2.052,2.958 true 0.521,4.458 0.625,4.458 0.625,4.458 0.708,4.365 false 1.219,4.073 1.323,4.073 1.323,4.073 1.406,3.979 false 3.646,3.875 3.75,3.875 3.75,3.875 3.885,4 false 4.302,4.125 4.385,4.125 4.385,4.125 4.542,4.375 false 0.354,4.396 0.531,4.573 0.177,0.177 10 false *a 1.052,4 1.229,4.177 0.177,0.177 10 false *a 3.469,3.781 3.646,3.958 0.177,0.177 10 false *a 4.115,4.031 4.292,4.208 0.177,0.177 10 false *a 0.604,0.333 0.771,0.521 0.167,0.188 10 true *1 3.656,0.49 3.823,0.677 0.167,0.188 10 true *1 2.844,2.313 3.01,2.5 0.167,0.188 10 true *1 6.677,2.156 6.844,2.344 0.167,0.188 10 true *1

Text in Illustration
*1 Timing Mark - -
*a Viewpoint - -

HINT:
A388752E01
2.458,0.49 2.615,0.688 0.156,0.198 10 false A 2.458,0.875 2.615,1.073 0.156,0.198 10 false B 2.458,1.208 2.615,1.406 0.156,0.198 10 false C 2.458,1.677 2.615,1.875 0.156,0.198 10 false D

for Intake Camshaft:

Be sure to check mark A at the point when marks B, C and D are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.



c.

If the valve timing is misaligned, reinstall the timing chain.


d.

Turn the crankshaft 2 revolutions, set the No. 1 cylinder to TDC/compression and check the timing marks again.


Hide 11324 15.INSTALL TIMING CHAIN COVER PLATE

a.

Install a new gasket and the timing chain cover plate with the 4 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 11201 17.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11202 18.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 11181A 20.INSTALL REAR CYLINDER HEAD COVER

Hide 16206 23.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

Hide 11452 24.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 17168 26.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 82715 27.INSTALL WIRING HARNESS CLAMP BRACKET

Hide 16604 28.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 16572D 35.INSTALL NO. 2 RADIATOR HOSE

Hide 16571C 36.INSTALL NO. 1 RADIATOR HOSE

Hide 74431 39.INSTALL BATTERY TRAY

Hide 28800 40.INSTALL BATTERY

Hide 28800A 42.CONNECT CABLE TO POSITIVE BATTERY TERMINAL

Hide 43.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 51405A 50.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY