Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY
RM1440E _52 Drivetrain _056134 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0273948 AUTOMATIC TRANSMISSION ASSEMBLY A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY

a.
C209683E02
1.302,0.833 1.125,0.24 1.125,0.24 1.042,0.24 true 1.188,2.427 1.354,3.021 1.354,3.021 1.438,3.021 true 2.313,0.313 2.49,0.51 0.177,0.198 10 false A 3.01,0.563 3.219,0.729 0.208,0.167 10 false *1 0.833,0.125 1.042,0.292 0.208,0.167 10 false *1 3.198,1.375 3.375,1.542 0.177,0.167 10 true *2 1.458,2.927 1.635,3.094 0.177,0.167 10 false *2

Using a vernier caliper and straightedge, measure dimension A between the transmission fitting surface of the engine *1 and the torque converter fitting surface of the drive plate *2 (step 1)


b.
C209685E02
0.603,0.428 0.956,0.029 0.956,0.029 0.719,0.622 false 0.956,0.029 1.14,0.029 false 1.145,0 1.318,0.159 0.173,0.159 10 *1

Aligning the matchmarks on the transmission case and torque converter clutch, and then mesh the splines of the input shaft and turbine runner.

Text in Illustration
*1 Matchmark


c.
C209687E03
0.98,1.749 0.995,0.163 false 0.61,0.454 0.992,0.169 0.992,0.169 1.114,0.169 false 1.148,0.073 1.311,0.222 0.163,0.149 10 *1

Mesh the splines of the stator shaft and stator while turning the torque converter clutch.

Text in Illustration
*1 Matchmark

HINT:

Turn the torque converter clutch approximately 180°.



d.
C217017E01
0.616,0.467 0.857,0.119 0.857,0.119 0.97,0.119 false 0.717,0.625 0.857,0.119 false 1.004,0.028 1.171,0.188 0.167,0.160 10 *1

Turn the torque converter clutch and align the matchmarks on the torque converter clutch and transmission case to mesh the key of the oil pump drive gear into the slot on the torque converter clutch.

Text in Illustration
*1 Matchmark

NOTICE:

Do not push on the torque converter when aligning the matchmarks.



e.
C209689E01
2.818,0.771 2.942,0.937 0.124,0.166 10 B

Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that B is more than A (measured in step 1).

Standard distance:

A + 1 mm (0.0394 in.) or more



Hide 33823 2.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the transmission assembly with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 36100 3.INSTALL TRANSFER ASSEMBLY

Hide 35000 4.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

a.
C218126E01
2.516,0.867 2.745,1.093 0.229,0.225 10 *1 1.563,0.986 2.481,0.986 false 0.754,0.882 1.068,1.086 0.314,0.204 10 *2

Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter clutch centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent

Maximum grease amount:

Approximately 1 g (0.0353 oz.)


Text in Illustration
*1 Torque Converter Clutch Centerpiece
*2 Crankshaft


b.
C217032E02
2.542,4.146 2.667,4.313 0.125,0.167 10 false B 0.531,2.531 0.656,2.677 0.125,0.146 10 false A 1.177,2.313 1.302,2.458 0.125,0.146 10 false A 2.313,2.323 2.438,2.469 0.125,0.146 10 false A 2.813,2.594 2.938,2.74 0.125,0.146 10 false A 2.938,3.615 3.063,3.76 0.125,0.146 10 false A 2.781,3.948 2.906,4.115 0.125,0.167 10 false B 0.771,4.167 0.896,4.333 0.125,0.167 10 true B 0.365,3.781 0.5,3.979 0.135,0.198 10 true B

Confirm that the 2 knock pins are on the transmission contact surface of the engine block before transmission installation.


c.

Install the transmission with the 9 bolts.

Torque:
for 17 mm head bolt A : 71 N*m (724 kgf*cm, 52 ft.*lbf)
for 14 mm head bolt B : 37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 36407 5.CONNECT BREATHER HOSE

a.

Connect the 3 breather plug hoses to the engine.


Hide 6.CONNECT WIRE HARNESS AND CONNECTOR

a.

Connect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and transfer control side connector.

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.

U148762



b.

Attach the 2 connector clamps and 7 harness clamps.


c.

Tilt up the automatic transmission.


d.

Connect the ground cable with the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 12371 7.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the rear engine mounting insulator to the transmission with the 4 bolts.

Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)


b.

Install the rear engine mounting heat insulator to the engine mounting insulator.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 51204 8.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


b.

Install the frame crossmember to the frame with the 4 bolts and 4 nuts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 51226A 9.INSTALL FRONT SUSPENSION MEMBER BRACKET LH AND RH

a.

Install the front suspension member bracket LH and front suspension member bracket RH with the 8 bolts.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)


Hide 32101A 10.INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

a.
C218128

Turn the crankshaft to gain access to the installation locations of the 6 bolts and install each bolt while holding the crankshaft pulley setting bolt with a wrench.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)

NOTICE:

Install the black bolt first, and then the 5 silver bolts.



b.

Install the flywheel housing side cover to the engine.


Hide 32921 11.CONNECT NO. 1 INLET OIL COOLER TUBE AND NO. 1 OUTLET OIL COOLER TUBE

a.

Temporarily install the ends of the oil cooler inlet tube and outlet tube to each oil cooler tube union by hand.


b.

Close the 2 flexible hose clamps and install the 2 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Using a union nut wrench, tighten the inlet and outlet tubes.

Torque:
34 N*m (346 kgf*cm, 25 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 28100 12.INSTALL STARTER ASSEMBLY

a.

Install the starter assembly (See page Engine / Hybrid System>1GR-FE STARTING>STARTER>INSTALLATION).


Hide 33820B 13.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Connect the transmission control cable to the transmission control cable bracket with a new clip, and connect the cable end to the control shaft lever with the nut.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 17118 14.INSTALL MANIFOLD STAY

a.

Install the stay with the 3 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 17119 15.INSTALL NO. 2 MANIFOLD STAY

a.

Install the stay with the 3 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 17410 16.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install the front exhaust pipe assembly (See page Engine / Hybrid System>1GR-FE INTAKE / EXHAUST>EXHAUST PIPE>INSTALLATION).


Hide 37110 17.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 37140 18.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 36179 19.INSTALL TRANSFER CASE LOWER PROTECTOR

a.

Install the transfer case lower protector with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page Power Source / Network>1GR-FE BATTERY / CHARGING>GENERATOR>INSTALLATION).


Hide 21.ADD AUTOMATIC TRANSMISSION FLUID

Hide 53736B 26.INSTALL NO. 1 FRONT FENDER APRON TO FRAME SEAL RH

Hide 51450 27.INSTALL REAR ENGINE UNDER COVER ASSEMBLY

Hide 51405A 28.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 29.RESET PERFORM RESET MEMORY

a.

Perform the Reset Memory procedures (A/T initialization) (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).