There may be a short circuit between the CAN bus lines and GND when the resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω.
| Symptom | Trouble Area |
|---|---|
| The resistance between terminals 6 (CANH) and 4 (CG) or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω. | ·
Short between CAN bus line and GND ·
Combination meter assembly ·
Skid control ECU (master cylinder solenoid) ·
Main body ECU (multiplex network body ECU) ·
Airbag sensor assembly ·
Steering angle sensor (spiral cable sub-assembly) ·
Radio and display receiver assembly*1 ·
Air conditioning amplifier assembly ·
Power steering ECU assembly ·
Yaw rate sensor assembly ·
Four wheel drive control ECU*2 ·
ECM ·
No. 1 junction connector ·
No. 2 junction connector ·
No. 3 junction connector ·
No. 4 junction connector |
*1: w/ Radio and Display Receiver Assembly
*2: for 4WD
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
NEXT
Disconnect the F59 No. 2 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F13-6 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F13-14 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
OK
NG
Reconnect the F59 No. 2 junction connector connector.
NEXT
Disconnect the A36 No. 1 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F13-6 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F13-14 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A36-1 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| A36-4 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A36-3 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| A36-6 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 1 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the A36 No. 1 junction connector connector.
NEXT
Disconnect the A6 skid control ECU (master cylinder solenoid) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| A6-11 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| A6-25 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid)) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the A36 No. 1 junction connector connector.
NEXT
Disconnect the F14 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F14-1 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F14-2 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Combination Meter Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the A36 No. 1 junction connector connector.
NEXT
Disconnect the F59 No. 2 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F59-3 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F59-14 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the F59 No. 2 junction connector connector.
NEXT
Disconnect the F60 No. 3 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F13-6 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F13-14 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F60-8 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F60-19 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
For vehicles without four wheel drive, go to "Check for Short to GND in CAN Bus Wire (No. 3 Junction Connector - Power Steering ECU Assembly)".
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F60-3 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F60-14 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F60-5 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F60-16 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F60-7 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F60-18 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F60-2 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F60-13 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 3 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the F60 No. 3 junction connector connector.
NEXT
Disconnect the F42 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F42-11 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F42-12 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the F60 No. 3 junction connector connector.
NEXT
Disconnect the F47 four wheel drive control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F47-19 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F47-20 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Four Wheel Drive Control ECU) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the F60 No. 3 junction connector connector.
NEXT
Disconnect the F41 power steering ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F41-1 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F41-2 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Power Steering ECU Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the F60 No. 3 junction connector connector.
NEXT
Disconnect the F36 yaw rate sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F36-3 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F36-2 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Yaw Rate Sensor Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the F60 No. 3 junction connector connector.
NEXT
Disconnect the F50 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F50-32 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F50-31 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to ECM) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the F60 No. 3 junction connector connector.
NEXT
Disconnect the G13 No. 4 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G13-5 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| G13-16 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 4 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G13-6 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| G13-17 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 4 Junction Connector) |
| *b | Front view of DLC3 |
| Result | Proceed to |
|---|---|
| OK (w/ Radio and Display Receiver Assembly) | A |
| OK (w/o Radio and Display Receiver Assembly) | B |
| NG | C |
A
B
C
Disconnect the G14 No. 4 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G14-6 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| G14-17 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 4 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G13 and G14 No. 4 junction connector connectors.
NEXT
Disconnect the G29 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G29-9 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| G29-10 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the G13 No. 4 junction connector connector.
NEXT
Disconnect the F59 No. 2 junction connector connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F59-1 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F59-12 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F59-2 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F59-13 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F59-5 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F59-16 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F59-7 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F59-18 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to No. 2 Junction Connector) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the F59 No. 2 junction connector connector.
NEXT
Disconnect the F9 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F9-14 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F9-13 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Main Body ECU (Multiplex Network Body ECU)) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the F59 No. 2 junction connector connector.
NEXT
Disconnect the F33 airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F33-13 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F33-22 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Front view of wire harness connector
(to Airbag Sensor Assembly) |
| *b | Front view of DLC3 |
OK
NG
Reconnect the F59 No. 2 junction connector connector.
NEXT
Disconnect the F19 steering angle sensor (spiral cable sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F19-4 (CANH) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| F19-3 (CANL) - F13-4 (CG) | Ignition switch off | 200 Ω or higher |
| *a | Rear view of wire harness connector
(to Steering Angle Sensor (Spiral Cable Sub-assembly)) |
| *b | Front view of DLC3 |
OK
NG