Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > VC Output Circuit

for Preparation Click here


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A116143E88

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON, and then goes off when the engine starts.


WIRING DIAGRAM


A288980E01


A288981E01


INSPECTION PROCEDURE

1.CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when the ignition switch is turned to ON.

    OK:
    MIL lights up.



NG
Go to step 2
OK

SYSTEM OK 

2.CHECK COMMUNICATION BETWEEN TECHSTREAM AND ECM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Check the communication between the Techstream and ECM.

    Result 
    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT (Click here)
B


3.CHECK MIL (THROTTLE BODY WITH MOTOR ASSEMBLY)
  1. Disconnect the B13 throttle body with motor assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the throttle body with motor assembly connector.



A
REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY (Click here)
B


4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)
  1. Disconnect the A3 accelerator pedal sensor assembly connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the accelerator pedal sensor assembly connector.



A
REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY (Click here)
B


5.CHECK MIL (NO. 1 EMISSION CONTROL VALVE SET)
  1. Disconnect the B51 No. 1 emission control valve set connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the No. 1 emission control valve set connector.



A
REPLACE NO. 1 EMISSION CONTROL VALVE SET (Click here)
B


6.CHECK MIL (NO. 2 EMISSION CONTROL VALVE SET)
  1. Disconnect the B52 No. 2 emission control valve set connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the No. 2 emission control valve set connector.



A
REPLACE NO. 2 EMISSION CONTROL VALVE SET (Click here)
B


7.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 1)
  1. Disconnect the B22 VVT sensor (for Intake Side of Bank 1) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the VVT sensor (for Intake Side of Bank 1) connector.



A
REPLACE VVT SENSOR (FOR INTAKE SIDE OF BANK 1) (Click here)
B


8.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 1)
  1. Disconnect the B23 VVT sensor (for Exhaust Side of Bank 1) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the VVT sensor (for Exhaust Side of Bank 1) connector.



A
REPLACE VVT SENSOR (FOR EXHAUST SIDE OF BANK 1) (Click here)
B


9.CHECK MIL (VVT SENSOR FOR EXHAUST SIDE OF BANK 2)
  1. Disconnect the B50 VVT sensor (for Exhaust Side of Bank 2) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the VVT sensor (for Exhaust Side of Bank 2) connector.



A
REPLACE VVT SENSOR (FOR EXHAUST SIDE OF BANK 2) (Click here)
B


10.CHECK MIL (VVT SENSOR FOR INTAKE SIDE OF BANK 2)
  1. Disconnect the B22 VVT sensor (for Intake Side of Bank 2) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the VVT sensor (for Intake Side of Bank 2) connector.



A
REPLACE VVT SENSOR (FOR INTAKE SIDE OF BANK 2) (Click here)
B


11.CHECK MIL (CANISTER PUMP MODULE)


    A225195
  1. Disconnect the O15 canister pump module connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the canister pump module connector.



A
REPLACE CANISTER ASSEMBLY (Click here)
B


12.CHECK MIL (POWER STEERING OIL PRESSURE SWITCH)
  1. Disconnect the B31 power steering oil pressure switch connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the power steering oil pressure switch connector.



A
REPLACE POWER STEERING OIL PRESSURE SWITCH (Click here)
B


13.CHECK HARNESS AND CONNECTOR
  1. Disconnect the B13 throttle body with motor assembly connector.

  1. Disconnect the A3 accelerator pedal sensor assembly connector.

  1. Disconnect the B51 No. 1 emission control valve set connector.

  1. Disconnect the B52 No. 2 emission control valve set connector.

  1. Disconnect the B21 VVT sensor (for Intake Side of Bank 1) connector.

  1. Disconnect the B23 VVT sensor (for Exhaust Side of Bank 1) connector.

  1. Disconnect the B50 VVT sensor (for Exhaust Side of Bank 2) connector.

  1. Disconnect the B22 VVT sensor (for Intake Side of Bank 2) connector.

  1. Disconnect the O15 canister pump module connector.

  1. Disconnect the B31 power steering oil pressure switch connector.

  1. Disconnect the B36, B38 and F50 ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B38-13 (VCTA) - Body ground
    Always
    10 kΩ or higher
    F50-4 (VCPA) - Body ground
    Always
    10 kΩ or higher
    F50-2 (VCP2) - Body ground
    Always
    10 kΩ or higher
    B36-15 (VCV1) - Body ground
    Always
    10 kΩ or higher
    B36-16 (VCV2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the throttle body with motor assembly connector.

  1. Reconnect the accelerator pedal sensor assembly connector.

  1. Reconnect the No. 1 emission control valve set connector.

  1. Reconnect the No. 2 emission control valve set connector.

  1. Reconnect the VVT sensor connectors.

  1. Reconnect the canister pump module connector.

  1. Reconnect the power steering oil pressure switch connector.

  1. Reconnect the ECM connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)