Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1237    Speed Sensor Rotor Faulty

DTC    C1275    Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)

DTC    C1276    Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)

DTC    C1277    Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)

DTC    C1278    Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)

for Preparation Click here


DESCRIPTION

The skid control ECU (brake actuator assembly) measures the speed of each wheel by receiving signals from the speed sensor.
These signals are used for recognizing that all four wheels are operating properly.
Therefore, all wheel signals must be equal.
DTCs C1275 to C1278 are cleared when the speed sensor sends a vehicle speed signal or when Test Mode ends. DTCs C1275 to C1278 are output only in Test Mode.

DTC No.
DTC Detection Condition
Trouble Area
C1237
Any of the following is detected:
  1. Discrepancy among four wheel speed sensor output.
  2. Abnormal pulse signals from 3 or more sensors.
  3. Continuous ABS control is performed for 60 seconds or more.
  4. VSC control is performed for 5 seconds or more.
  1. Tire and wheel size
  2. Tire deformation
  3. Speed sensor rotor
  4. Speed sensor
  5. Speed sensor circuit
  6. Skid control ECU (Brake actuator assembly)
C1275
C1276
Detected only during Test Mode.
Front speed sensor rotor RH/LH (Front axle hub sub-assembly RH/LH)
C1277
C1278
Detected only during Test Mode.
Rear speed sensor rotor RH/LH (Rear axle hub and bearing assembly RH/LH)

HINT:
  1. DTC C1275 is for the front speed sensor RH.
  2. DTC C1276 is for the front speed sensor LH.
  3. DTC C1277 is for the rear speed sensor RH.
  4. DTC C1278 is for the rear speed sensor LH.


WIRING DIAGRAM

Refer to DTCs C1330, C1331, C1332, C1333, C1464, C1465, C1466 and C1467 .

HINT:
When C1330, C1331, C1332, C1333, C1464, C1465, C1466 and/or C1467 is output together with C1237, inspect and repair the trouble areas indicated by C1330, C1331, C1332, C1333, C1464, C1465, C1466 and/or C1467 first (Click here for front, and/or Click here for rear).

1.CHECK TIRES
  1. Check the size and condition of all four wheels (Click here).

    HINT:
    The DTC is output when tire deformation or a difference in tire size is detected.

    OK:
    The diameter of all four tires and the tire pressure are the same.



NG
REPLACE TIRES SO THAT ALL FOUR TIRES ARE THE SAME SIZE
OK


2.READ VALUE USING GTS (SPEED SENSOR)
  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Select the Data List using the GTS (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Front wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    FL Wheel Speed
    Front wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    RR Wheel Speed
    Rear wheel speed sensor RH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations
    RL Wheel Speed
    Rear wheel speed sensor LH reading / Min.: 0 km/h (0 mph), Max.: 326.4 km/h (202 mph)
    Vehicle stopped: 0 km/h (0 mph)
    When driving at constant speed: No large fluctuations

  1. Check the speed value output from the speed sensor displayed on the GTS.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire pressure, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart (Click here).

    OK:
    The speed value output from the speed sensor displayed on the GTS is similar to the speed indicated on the speedometer.


    Result:

    Result
    Proceed to
    OK
    A
    NG (for front)
    B
    NG (for rear)
    C



B
Go to step 5

C
Go to step 13
A


3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
  1. Turn the ignition switch off.

  1. Perform the sensor check using the Test Mode procedure (Click here).

    OK:
    All Test Mode DTCs are not output.


    Result:

    Result
    Proceed to
    OK
    A
    NG (for front)
    B
    NG (for rear)
    C



B
Go to step 5

C
Go to step 13
A


4.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1237 is not output.
    A
    DTC C1237 is output (for front).
    B
    DTC C1237 is output (for rear).
    C



B
Go to step 9

C
Go to step 17
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

5.CHECK FRONT SPEED SENSOR INSTALLATION


    C168336E09
  1. Turn the ignition switch off.

  1. Check the speed sensor installation.

    OK:
    There is no clearance between the sensor and the steering knuckle.
    The installation bolt is tightened properly.
    Torque:
    7.5 N*m (76 kgf*cm, 66 in.*lbf)

    Text in Illustration 
    *1
    Front Speed Sensor
    *a
    Correct
    *b
    Incorrect
    *c
    7.5 N*m
    *d
    No clearance



NG
INSTALL FRONT SPEED SENSOR CORRECTLY (Click here)
OK


6.CHECK FRONT SPEED SENSOR TIP
  1. Remove the front speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE FRONT SPEED SENSOR
OK


7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - FRONT SPEED SENSOR)
  1. Install the front speed sensor (Click here).

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU (brake actuator assembly) connector and the front speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A5-16 (FR+) - A42-2 (FR+)
    Always
    Below 1 Ω
    A5-16 (FR+) - Body ground
    Always
    10 kΩ or higher
    A5-4 (FR-) - A42-1 (FR-)
    Always
    Below 1 Ω
    A5-4 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    A5-19 (FL+) - A12-2 (FL+)
    Always
    Below 1 Ω
    A5-19 (FL+) - Body ground
    Always
    10 kΩ or higher
    A5-8 (FL-) - A12-1 (FL-)
    Always
    Below 1 Ω
    A5-8 (FL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.RECONFIRM DTC
  1. Reconnect the skid control ECU (brake actuator assembly) connector and the front speed sensor connector.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1237 is output.
    A
    DTC C1237 is not output.
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


9.REPLACE FRONT SPEED SENSOR
  1. Turn the ignition switch off.

  1. Replace the front speed sensor (Click here).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


10.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.

  1. Check if the same DTC is output (Click here).


Result:

Result
Proceed to
DTC C1237 is output.
A
DTC C1237 is not output.
B



B
END
A


11.REPLACE FRONT SPEED SENSOR ROTOR
  1. Turn the ignition switch off.

  1. Replace the front speed sensor rotor (Click here).

    HINT:
    If the front speed sensor rotor needs to be replaced, replace the front axle hub sub-assembly.

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


12.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.

  1. Check if the same DTC is output (Click here).


Result:

Result
Proceed to
DTC C1237 is output.
A
DTC C1237 is not output.
B



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

13.CHECK REAR SPEED SENSOR INSTALLATION


    C168336E09
  1. Turn the ignition switch off.

  1. Check the speed sensor installation.

    OK:
    There is no clearance between the sensor and the rear axle carrier sub-assembly.
    The installation bolt is tightened properly.
    Torque:
    7.5 N*m (76 kgf*cm, 66 in.*lbf)

    Text in Illustration 
    *1
    Rear Speed Sensor
    *a
    Correct
    *b
    Incorrect
    *c
    7.5 N*m
    *d
    No clearance



NG
INSTALL REAR SPEED SENSOR CORRECTLY (Click here)
OK


14.CHECK REAR SPEED SENSOR TIP
  1. Remove the rear speed sensor (Click here).

  1. Check the speed sensor tip.

    OK:
    No scratches or foreign matter on the sensor tip.

    NOTICE:
    Check the speed sensor signal after cleaning or replacement (Click here).



NG
CLEAN OR REPLACE REAR SPEED SENSOR
OK


15.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR SPEED SENSOR)
  1. Install the rear speed sensor (Click here).

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU (brake actuator assembly) connector and the rear speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH:
    Tester Connection
    Condition
    Specified Condition
    A5-17 (RR+) - G9-2 (RR+)
    Always
    Below 1 Ω
    A5-17 (RR+) - Body ground
    Always
    10 kΩ or higher
    A5-29 (RR-) - G9-1 (RR-)
    Always
    Below 1 Ω
    A5-29 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH:
    Tester Connection
    Condition
    Specified Condition
    A5-31 (RL+) - H12-2 (RL+)
    Always
    Below 1 Ω
    A5-31 (RL+) - Body ground
    Always
    10 kΩ or higher
    A5-18 (RL-) - H12-1 (RL-)
    Always
    Below 1 Ω
    A5-18 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.RECONFIRM DTC
  1. Reconnect the skid control ECU (brake actuator assembly) connector and the rear speed sensor connector.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.

  1. Check if the same DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC C1237 is output.
    A
    DTC C1237 is not output.
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


17.REPLACE REAR SPEED SENSOR
  1. Turn the ignition switch off.

  1. Replace the rear speed sensor (Click here).

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


18.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.

  1. Check if the same DTC is output (Click here).


Result:

Result
Proceed to
DTC C1237 is output.
A
DTC C1237 is not output.
B



B
END
A


19.REPLACE REAR SPEED SENSOR ROTOR
  1. Turn the ignition switch off.

  1. Replace the rear speed sensor rotor (Click here).

    HINT:
    If the rear speed sensor rotor needs to be replaced, replace the rear axle hub and bearing assembly.

    NOTICE:
    Check the speed sensor signal after replacement (Click here).


NEXT


20.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.

  1. Check if the same DTC is output (Click here).


Result:

Result
Proceed to
DTC C1237 is output.
A
DTC C1237 is not output.
B



B
END
A

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)