Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P050A  Cold Start Idle Air Control System Performance  P050B  Cold Start Ignition Timing Performance  


DESCRIPTION

Cold start emission reduction strategy (CSERS) is employed to shorten the time to catalyst light-off from cold start. CSERS consists of retarded ignition timing and increased engine idle speed for a calibrated period of time. This monitor detects malfunctions of the estimated exhaust gas temperature, ECM commanded ignition timing and engine idle speed not reaching the target values.

DTC No. DTC Detection Condition Trouble Area
P050A The engine speed does not achieve the target engine speed for 7 seconds with engine cooled down.
(2 trip detection logic)
·

Throttle with motor body assembly

·

Mass air flow meter

·

PCV system

·

Air cleaner filter element

·

Intake system

·

VVT system

·

Wire harness or connector

·

ECM


P050B The ignition timing is not retarded for 7 seconds, despite rapid warming control of the catalyst (to retard the ignition timing).
(2 trip detection logic)

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Check the coolant temperature recorded in the Freeze Frame data.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

8.

Check that the coolant temperature is the same as that recorded in the Freeze Frame data.

HINT:

If the conditions are not met, then turn the ignition switch off, and wait until the conditions are met.


9.

Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.

10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P050A or P50B.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



15.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P050A OR P050B)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
DTC P050A or P050B is output A
DTC P050A or P050B and other DTCs are output B

HINT:

If any DTCs other than P050A or P050B are output, troubleshoot those DTCs first.




A

2.READ VALUE USING GTS (FUEL TRIM)

B

2.READ VALUE USING GTS (FUEL TRIM)
HINT:

Calculate the total fuel trim values to check the characteristic deviation of the mass air flow meter.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Short FT #1 and Long FT #1.


e.

Read the values displayed on the GTS at engine idle.


f.

Add together the Short FT #1 and Long FT #1 values to obtain the total fuel trim.

Standard:

Total of Short FT #1 and Long FT #1 values is between -20% and 20%.




OK

3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)

NG

5.CHECK PCV SYSTEM
3.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)
a.

Check that there are no deposits around the throttle valve and throttle valve condition.

OK:

No deposits around the throttle valve and throttle valve moves smoothly.


Result
Result Proceed to
NG A
OK B



A

4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

B

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A OR P050B)
4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY
a.

Replace the throttle with motor body assembly (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>THROTTLE BODY>REMOVAL).



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A OR P050B)
5.CHECK PCV SYSTEM
a.

Check the PCV hose connections (See page Engine / Hybrid System>FA20 EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).

OK:

PCV valve and hose are connected correctly and are not damaged.




OK

6.CHECK INTAKE SYSTEM

NG

10.REPAIR OR REPLACE PCV HOSE
6.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks (See page Engine / Hybrid System>FA20 INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leaks from the intake system.




OK

7.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

NG

11.REPAIR OR REPLACE INTAKE SYSTEM
7.CHECK AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Visually check that the air cleaner filter element is not excessively contaminated with dirt or oil.

OK:

The air cleaner filter element is not excessively contaminated with dirt or oil.




OK

8.PERFORM ACTIVE TEST USING GTS (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)

NG

12.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
8.PERFORM ACTIVE TEST USING GTS (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE)
a.

Operate the VVT system through the Active test, and check if the VVT system is operating normally.

i.

Perform the Active Test, referring to DTC P000A inspection procedure (VVT system for intake camshaft) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>P000A).


ii.

Perform the Active Test, referring to DTC P000B inspection procedure (VVT system for exhaust camshaft) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>P000B).




OK

9.READ VALUE USING GTS (MAF)

NG

13.CHECK AND REPAIR VVT SYSTEM
9.READ VALUE USING GTS (MAF)

OK

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A OR P050B)

NG

15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
10.REPAIR OR REPLACE PCV HOSE
a.

Repair or replace the PCV valve or hose.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A OR P050B)
11.REPAIR OR REPLACE INTAKE SYSTEM
a.

Repair or replace the intake system.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A OR P050B)
12.REPLACE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
a.

Replace the air cleaner filter element sub-assembly.



NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A OR P050B)
13.CHECK AND REPAIR VVT SYSTEM
a.

Check and repair the VVT system.


HINT:
·

Refer to DTC P000A Inspection Procedure (VVT system for intake camshaft) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>P000A).

·

Refer to DTC P000B Inspection Procedure (VVT system for exhaust camshaft) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>P000B).




NEXT

14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A OR P050B)
14.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A OR P050B)
NOTICE:

In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


h.

Input the DTC: P050A or P050B.


i.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P050A or P050B is output) B



A

B

15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
15.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

HINT:

Repair any problems.




NEXT

16.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A OR P050B)
16.CHECK WHETHER DTC OUTPUT RECURS (DTC P050A OR P050B)
NOTICE:

In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


h.

Input the DTC: P050A or P050B.


i.

Check the DTC judgment result.

Result
Result Proceed to
ABNORMAL (DTC P050A or P050B is output) A
NORMAL (DTC is not output) B



A

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

B

END

17.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

OK

18.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL).

HINT:

If the results of the inspections performed in step 9 indicated no problem, proceed to the next step without replacing the mass air flow meter.




NEXT

19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
19.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
NOTICE:

In this operation, the engine must be cold (approximately the same as the engine coolant temperature recorded in the freeze frame data).


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


g.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


h.

Input the DTC: P050A or P50B.


i.

Check the DTC judgment result.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P050A or P050B is output) B



A

END

B