Home › Engine / Hybrid System › FA20 (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2016.06
RM2090E _51 Engine / Hybrid System _060666 FA20 ENGINE MECHANICAL _0297495 ENGINE ASSEMBLY A

FA20 ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 53301 1.SET HOOD SUB-ASSEMBLY

A276897E04
5.344,0.156 5.469,0.323 0.125,0.167 10 true A 5.281,0.781 5.406,0.927 0.125,0.146 10 true B 4.813,2.156 4.938,2.302 0.125,0.146 10 true A 5.688,1.417 5.813,1.563 0.125,0.146 10 true B

a.

Change the front hood stay position from A to B, and support the hood sub-assembly at position B.


Hide 2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (w/ Air Conditioning System)

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 53608 5.REMOVE FRONT SUSPENSION UPPER TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607 6.REMOVE FRONT SUSPENSION UPPER TO COWL BRACE SUB-ASSEMBLY RH

Hide 7.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

a.
A281521

Disconnect the hose.


b.
A281071

Remove the 2 bolts and disconnect the chamber.


c.
A283417

Loosen the hose clamp and disconnect the No. 2 ventilation hose.


d.
A283418

Disconnect the mass air flow meter connector.


e.

Disengage the clamp and separate the wire harness from the air cleaner cap.


f.
C257564

Loosen the hose clamp.


g.
A283420

Remove the 3 bolts and air cleaner cap with air cleaner hose.


h.
A281495

Remove the bolt and stay from the body.


Hide 16470 10.REMOVE RADIATOR RESERVE TANK ASSEMBLY

Hide 16502 11.REMOVE WATER FILLER SUB-ASSEMBLY

A276898

a.

Remove the 2 bolts and disconnect the water filler sub-assembly.


b.

Remove the 2 clamps and water filler sub-assembly.


Hide 13.DISCONNECT ENGINE WIRE (for RHD)

HINT:

Fix the disconnected harness components with tape to keep them out of the way.


a.

for Automatic Transmission:

i.
A276929E03
2.354,0.469 2.51,0.656 0.156,0.188 10 true A 1.031,0.573 1.156,0.75 0.125,0.177 10 true B

Release the lock of connector (A) and disconnect the connector.


ii.

Disconnect the connector (B).


iii.

Disconnect the 2 wire harness clamps.


iv.
A276930

Slide the connector in the direction shown in the illustration, and disconnect the wire harness.



b.
A392630E01
2.073,0.469 2.229,0.667 0.156,0.198 10 false A 0.51,0.365 0.667,0.563 0.156,0.198 10 false B

Remove the 2 bolts and the wire harness bracket from the No. 2 engine hanger.


c.

Release the lock of connector (A) and disconnect the connector.


d.

Disconnect the connector (B).


e.
A276902

Disconnect the wire harness clamp and wire harness from the No. 2 engine hanger.


f.
A276900

Disconnect the 2 wire harness clamps.


g.

Remove the 2 bolts and 2 wire harness clamp brackets.


h.
A276901

Disconnect the 5 wire harness clamps.


i.
A276903

Disconnect the terminal cap.


j.

Remove the nut and disconnect the wire harness from terminal B.


k.

Disconnect the generator connector and disengage the clamp.


Hide 14.DISCONNECT ENGINE WIRE (for LHD)

HINT:

Fix the disconnected harness components with tape to keep them out of the way.


a.
A392630E01
2.073,0.469 2.229,0.667 0.156,0.198 10 false A 0.51,0.365 0.667,0.563 0.156,0.198 10 false B

Remove the 2 bolts and the wire harness clamp bracket from the No. 2 engine hanger.


b.

Release the lock of connector (A) and disconnect the connector.


c.

Disconnect the connector (B).


d.
A282282

Disconnect the connector.


e.
A276902

Disconnect the wire harness clamp and wire harness from the No. 2 engine hanger.


f.
A281063

Disconnect the 3 wire harness clamps.


g.

for Automatic Transmission:

i.
A281064E03
1.719,0.198 1.844,0.385 0.125,0.188 10 true A 1.24,1.063 1.375,1.26 0.135,0.198 10 true B

Release the lock of connector (A) and disconnect the connector.


ii.

Disconnect the connector (B).


iii.
A281065

Slide the connector in the direction shown in the illustration, and disconnect the wire harness.


iv.
A392631

Disconnect the 4 wire harness clamps.


v.

Remove the bolt and wire harness clamp bracket.



h.
A276903

Disconnect the terminal cap.


i.

Remove the nut and disconnect the wire harness from terminal B.


j.

Disconnect the generator connector and disengage the clamp.


Hide 12601B 15.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 44771 16.DISCONNECT VACUUM TUBE CONNECTOR HOSE (for Automatic Transmission)

a.

for LHD:

i.
A281061

Loosen the hose clamp and disconnect the vacuum tube connector hose.


ii.
A281062

Remove the 2 bolts and disconnect the vacuum tube connector hose.



b.

for RHD:

i.
C260988

Loosen the hose clamp and disconnect the union to check valve hose.



Hide 44771 17.DISCONNECT VACUUM TUBE CONNECTOR HOSE (for Manual Transmission)

a.
C264090E02
0.135,0.146 0.417,0.396 0.281,0.25 12 true *A: 0.125,2.292 0.438,2.573 0.313,0.281 12 true *B:

Loosen the hose clamp and disconnect the union to check valve hose from the intake manifold.

Text in Illustration
*A for LHD
*B for RHD


Hide 17141 18.REMOVE EXHAUST MANIFOLD

Hide 17401 19.FIX FRONT EXHAUST PIPE SUB-ASSEMBLY (for Manual Transmission)

a.
A277903

Tie the front exhaust pipe sub-assembly to the front cross member sub-assembly with rope.


Hide 20.DISCONNECT HEATER WATER HOSE

a.
A276056

Loosen the 2 hose clamps and disconnect the 2 heater water hoses.


Hide 32943 21.DISCONNECT NO. 1 TRANSMISSION OIL COOLER HOSE (for Automatic Transmission)

a.
A281713

Loosen the clip and disconnect the No. 1 transmission oil cooler hose.


Hide 88704 22.REMOVE SUCTION HOSE SUB-ASSEMBLY (w/ Air Conditioning System)

a.
E246390

Remove the bolt and disconnect the suction hose sub-assembly from the compressor assembly with pulley.


b.

Remove the O-ring from the discharge hose sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



c.

for LHD:

i.
A282283

Remove the bolt and slide the hook connector.


ii.

Remove the nut and suction pipe sub-assembly.


iii.

Remove the O-ring from the suction pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.




d.

for RHD:

i.
E246448

Remove the bolt and slide the hook connector.


ii.

Disconnect the suction pipe sub-assembly.


iii.

Remove the O-ring from the suction pipe sub-assembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.




Hide 88711 23.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE (w/ Air Conditioning System)

Hide 28100 24.REMOVE STARTER ASSEMBLY (for Automatic Transmission)

Hide 28100 25.REMOVE STARTER ASSEMBLY (for Manual Transmission)

Hide 32943C 26.DISCONNECT NO. 3 TRANSMISSION OIL COOLER HOSE (for Automatic Transmission)

a.
A281712

Loosen the clip and disconnect the No. 3 transmission oil cooler hose.


Hide 16572 27.DISCONNECT RADIATOR OUTLET HOSE

a.
A276058

Loosen the clip and disconnect the radiator outlet hose.


Hide 28.DISCONNECT GROUNDED CABLE

a.
A276059

Remove the 2 bolts and disconnect the 2 grounded cables.


Hide 51444A 29.REMOVE REAR ENGINE UNDER COVER LH (w/ Floor Under Cover)

a.
C258518

Remove the 3 bolts and 8 clips, then remove the rear engine under cover LH.


Hide 48811 30.REMOVE FRONT STABILIZER BAR (for Automatic Transmission)

Hide 17401 31.FIX FRONT EXHAUST PIPE ASSEMBLY (for Automatic Transmission)

a.
A277903

Tie the front exhaust pipe assembly to the front cross member sub-assembly with rope.


Hide 35000 32.SEPARATE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

a.
A281519E01
0.814,0 0.944,0.150 0.130,0.150 10 B 0.318,0.663 0.448,0.813 0.130,0.150 10 A 0.422,1.526 0.552,1.676 0.130,0.150 10 A 2.939,1.494 3.069,1.644 0.130,0.150 10 A

Remove the 3 bolts and 2 nuts.

Text in Illustration
V100135

Bolt
V100136

Nut

NOTICE:

In order to prevent dropping, do not remove bolt B.



Hide 30300 33.REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)

a.
A281520E01
0.734,0 0.864,0.150 0.130,0.150 10 B 0.292,0.806 0.422,0.957 0.130,0.150 10 A 0.335,1.355 0.465,1.505 0.130,0.150 10 A 2.905,1.334 3.035,1.484 0.130,0.150 10 A

Remove the 3 bolts and 2 nuts.

Text in Illustration
V100135

Bolt
V100136

Nut

NOTICE:

In order to prevent dropping, do not remove bolt B.



Hide 57104A 34.SEPARATE FRONT CROSS MEMBER SUB-ASSEMBLY

a.
A276061

Remove the 2 nuts from the front cross member sub-assembly.


Hide 32101C 36.REMOVE DRIVE PLATE SETTING HEXAGON BOLT (for Automatic Transmission)

Hide 37.SEPARATE FUEL HOSE

a.

for Clamp Type:

i.
C257571E01
0.607,1.485 0.779,1.664 0.172,0.179 10 *a 1.82,1.385 0.835,1.538 0.835,1.538 1.295,0.902 false 1.458,1.239 0.847,1.531 false

Put matchmarks on the fuel hoses and fuel pipes.

Text in Illustration
*a matchmark


ii.

Remove the clamp and disconnect the fuel tube, No. 2 fuel tube and fuel tube from the fuel pipe.



b.

for Metal Type:

i.
C264501

Using SST, disconnect the fuel tube and No. 2 fuel tube from the fuel pipe (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>PRECAUTION).

SST
SU003-03936  


ii.
A282016

Remove the clamp and disconnect the No. 2 fuel vapor feed hose from the fuel pipe.



Hide 38.INSTALL ENGINE HANGER

a.
A276063E03
1.948,3.646 2.198,3.583 false 1.927,0.979 2.177,0.917 false 2.229,3.5 2.406,3.667 0.177,0.167 10 true *1 2.208,0.833 2.375,0.99 0.167,0.156 10 false *2

Install the engine hanger with the bolt, as shown in the illustration.

Text in Illustration
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger

Torque:
43 N*m (439 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-38030
Bolt 90119-14120



b.

Use an engine sling device and a mini crane to hold the engine.


Hide 39.SUPPORT TRANSMISSION ASSEMBLY

a.
A276064

Support the transmission assembly clutch housing with a jack.

NOTICE:

Support the transmission assembly until the installation of the engine assembly is completed.



Hide 12000 40.REMOVE ENGINE ASSEMBLY

a.
A281496E01
0.156,0.101 0.406,0.292 0.251,0.191 12 *A: 0.156,2.404 0.406,2.595 0.251,0.191 12 *B:

Remove the bolt from the transmission assembly.

Text in Illustration
*A for Automatic Transmission
*B for Manual Transmission


b.

Hoist the engine assembly up with an engine sling device and a mini crane.


Hide 32101 41.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

Hide 31210 42.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31250 43.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 13405 44.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

Hide 19315 45.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

Hide 46.INSTALL ENGINE STAND

a.

Set the engine on an engine stand.

NOTICE:

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



Hide 12311 47.REMOVE FRONT ENGINE MOUNTING BRACKET

a.
A276925

Remove the 4 bolts and 2 front engine mounting brackets.