Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.11–2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C0200/21  Right Front Wheel Speed Sensor Signal  C0205/22  Left Front Wheel Speed Sensor Signal  C1235/25  Foreign Object is Attached on Tip of Front Speed Sensor RH  C1236/26  Foreign Object is Attached on Tip of Front Speed Sensor LH  C1271/81  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272/82  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1275/85  Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1276/86  Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC)  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly). These signals are used for the anti-lock brake system. Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn. Each speed sensor detects that magnetic field change and sends a pulse signal to the skid control ECU (brake actuator assembly).

HINT:

When the connectors between the speed sensor and skid control ECU (brake actuator assembly) are connected, the following waveform is output.


C248680E02
1.417,1.219 1.635,1.219 1.635,1.219 1.635,1.458 false 1.5,0.396 1.875,0.396 1.875,0.396 1.875,0.906 false 6.333,1.323 6.948,1.75 0.615,0.427 10 1.4 V 6.333,1.688 6.875,2.031 0.542,0.344 10 0.7 V 4.281,2.188 5.219,2.625 0.938,0.438 10 Low Speed 5.24,2.167 6.292,2.688 1.052,0.521 10 High Speed 4.083,0.302 6.063,0.802 1.979,0.5 10 Waveform (Reference): 0.177,0.292 1.698,0.75 1.521,0.458 10 Front Speed Sensor 0.104,1.115 1.615,1.573 1.51,0.458 10 Speed Sensor Rotor 4.083,0.656 7.125,1.281 3.042,0.625 10 Between Speed Sensor (-) and Body Ground

HINT:

Measure the connection status between the sensor connector and the vehicle wire harness.


DTC No. Detection Item DTC Detection Condition Trouble Area
C0200/21 Right Front Wheel Speed Sensor Signal
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Front speed sensor

·

Speed sensor circuit

·

Speed sensor rotor

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


C0205/22 Left Front Wheel Speed Sensor Signal
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Front speed sensor

·

Speed sensor circuit

·

Speed sensor rotor

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


C1235/25 Foreign Object is Attached on Tip of Front Speed Sensor RH
1.

The wheel deceleration rate is 51.2 G or more and no pulse signal is input 7 times.

2.

The vehicle speed is 10 km/h or higher and no pulse signal is output from the wheel speed sensor for more than 30 seconds.

3.

All of the following conditions are met.

1.

Vehicle speed is 10 km/h or higher.

2.

Stop light switch is off.

3.

Only one wheel speed sensor indicates 0 km/h.

4.

The difference in wheel speed between the other 3 wheels is less than 2 km/h for more than 0.35 second.


4.

With vehicle speed higher than 20 km/h and no pulse signal is output from the front wheel speed sensor for 20 seconds, and this condition has happened 8 trips in a row, and then has continued for more than 10 seconds.

5.

Wheel deceleration rate at 51.2 G or more is detected more than 75 times in 5 seconds.

6.

At vehicle speed of 10 km/h (6 mph) or more, noise input once per rotor rotation for 15 seconds or more.

7.

Continuous ABS control for 45 seconds or more.


·

Front speed sensor

·

Speed sensor circuit

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


C1236/26 Foreign Object is Attached on Tip of Front Speed Sensor LH
1.

The wheel deceleration rate is 51.2 G or more and no pulse signal is input 7 times.

2.

The vehicle speed is 10 km/h or higher and no pulse signal is output from the wheel speed sensor for more than 30 seconds.

3.

All of the following conditions are met.

1.

Vehicle speed is 10 km/h or higher.

2.

Stop light switch is off.

3.

Only one wheel speed sensor indicates 0 km/h.

4.

The difference in wheel speed between the other 3 wheels is less than 2 km/h for more than 0.35 second.


4.

With vehicle speed higher than 20 km/h and no pulse signal is output from the front wheel speed sensor for 20 seconds, and this condition has happened 8 trips in a row, and then has continued for more than 10 seconds.

5.

Wheel deceleration rate at 51.2 G or more is detected more than 75 times in 5 seconds.

6.

At vehicle speed of 10 km/h (6 mph) or more, noise input once per rotor rotation for 15 seconds or more.

7.

Continuous ABS control for 45 seconds or more.


·

Front speed sensor

·

Speed sensor circuit

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


C1271/81 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor

·

Sensor installation

·

Speed sensor rotor

·

Skid control ECU (Brake actuator assembly)


C1272/82 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Front speed sensor

·

Sensor installation

·

Speed sensor rotor

·

Skid control ECU (Brake actuator assembly)


C1275/85 Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Speed sensor rotor

·

Skid control ECU (Brake actuator assembly)


C1276/86 Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Speed sensor rotor

·

Skid control ECU (Brake actuator assembly)



HINT:
·

DTCs C0200/21, C1235/25, C1271/81 and C1275/85 are for the front speed sensor RH.

·

DTCs C0205/22, C1236/26, C1272/82 and C1276/86 are for the front speed sensor LH.



WIRING DIAGRAM

C248681E03
5.323,0.844 5.802,1.25 0.479,0.406 10 19 5.583,0.948 6.063,1.344 0.479,0.396 10 FL1 5.323,1.156 5.854,1.635 0.531,0.479 10 18 2.333,0.854 2.75,1.26 0.417,0.406 10 1 2.333,1.167 2.688,1.51 0.354,0.344 10 2 2.333,1.781 2.677,2.177 0.344,0.396 10 1 2.333,2.083 2.677,2.458 0.344,0.375 10 2 5.583,1.25 6.167,1.656 0.583,0.406 10 FL0 2.156,0.938 2.573,1.333 0.417,0.396 10 + 2.177,1.24 2.573,1.615 0.396,0.375 10 - 2.156,1.865 2.448,2.271 0.292,0.406 10 + 2.177,2.156 2.469,2.521 0.292,0.365 10 - 5.406,1.771 5.781,2.094 0.375,0.323 10 7 5.583,1.854 6.094,2.25 0.51,0.396 10 FR1 5.396,2.083 5.729,2.438 0.333,0.354 10 6 5.583,2.167 6.177,2.573 0.594,0.406 10 FR0 4.99,2.448 5.49,2.792 0.5,0.344 10 B10 0.313,0.729 0.927,1.135 0.615,0.406 10 B11 4.99,2.625 7.021,3.635 2.031,1.01 10 SKID CONTROL ECU(BRAKE ACTUATOR ASSEMBLY) 0.302,0.896 1.375,1.802 1.073,0.906 10 FRONT SPEED SENSOR LH 0.313,1.625 0.917,2.063 0.604,0.438 10 A8 0.302,1.792 1.458,2.688 1.156,0.896 10 FRONT SPEED SENSOR RH

CAUTION / NOTICE / HINT

NOTICE:

If the brake actuator is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FR/FL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Start the engine.


d.

Enter the following menus: Chassis / ABS/VSC / Data List.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 509 45,46

e.

According to the display on the tester, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH reading min.: 0 km/h (0 mph)
max.: 326.4 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
FL Wheel Speed Front speed sensor LH reading min.: 0 km/h (0 mph)
max.: 326.4 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.

f.

Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


Result:
Proceed to
OK
NG




OK

2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

4.CHECK FRONT SPEED SENSOR INSTALLATION
2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Perform the sensor check in the Test Mode procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 509 3
OK:

All Test Mode DTCs are cleared.


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

4.CHECK FRONT SPEED SENSOR INSTALLATION
3.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 509

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC not output. A
DTC output. B


NOTICE:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

9.RECONFIRM DTC
4.CHECK FRONT SPEED SENSOR INSTALLATION
C108871C03
0.698,1.365 0.958,1.76 false 0.104,0.094 0.479,0.438 0.375,0.344 10 *1 1.031,1.781 1.406,2.125 0.375,0.344 10 *a 0.427,1.708 0.802,2.052 0.375,0.344 10 *b 2.719,1.833 3.094,2.177 0.375,0.344 10 *c
*1 Front Speed Sensor
*a No clearance
*b CORRECT
*c INCORRECT


a.

Turn the ignition switch off.


b.

Check the speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>INSTALLATION

OK:

There is no clearance between the sensor and the front steering knuckle. The installation bolt is tightened properly.


Result:
Proceed to
OK
NG




OK

5.INSPECT SPEED SENSOR TIP

NG

INSTALL FRONT SPEED SENSOR CORRECTLY

5.INSPECT SPEED SENSOR TIP
a.

Turn the ignition switch off.



c.

Check the speed sensor tip.

OK:

No scratches or foreign matter on the sensor tip.


NOTICE:

Do not replace the speed sensor if no damage to the speed sensor tip is found.



HINT:
·

If the sensor is contaminated with oil or other foreign material, clean the sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction. Confirm that the rotor is not contaminated with foreign material before replacing the sensor.

Result:
Proceed to
OK
NG





OK

6.INSPECT FRONT SPEED SENSOR

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

6.INSPECT FRONT SPEED SENSOR
a.

Turn the ignition switch off.



c.

Inspect the front speed sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>INSTALLATION

Result:
Proceed to
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

REPLACE FRONT SPEED SENSOR

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Disconnect the B10 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A8*1 or B11*2 front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

*1: for RH

*2: for LH


Standard Resistance (Check for Open):
for RH
Tester Connection Condition Specified Condition
B10-7 (FR1) - A8-1 (+) Always Below 1 Ω
B10-6 (FR0) - A8-2 (-) Always Below 1 Ω

for LH
Tester Connection Condition Specified Condition
B10-19 (FL1) - B11-1 (+) Always Below 1 Ω
B10-18 (FL0) - B11-2 (-) Always Below 1 Ω


Standard Resistance (Check for Short):
for RH
Tester Connection Condition Specified Condition
B10-7 (FR1) - Body ground Always 10 kΩ or higher
B10-6 (FR0) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
B10-19 (FL1) - Body ground Always 10 kΩ or higher
B10-18 (FL0) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

8.REPLACE FRONT SPEED SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.


b.

Replace the front speed sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

Result:
Proceed to
NEXT




NEXT

9.RECONFIRM DTC
9.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 509

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC output. A
DTC not output. B


Chassis > ABS/VSC/TRC > Trouble Codes
50001 509


A

10.INSPECT SKID CONTROL SENSOR ROTOR

B

END

10.INSPECT SKID CONTROL SENSOR ROTOR
a.

Replace the front axle hub bearing (front speed sensor rotor).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL

HINT:
·

The front speed sensor rotor is incorporated into the front axle hub bearing.

·

If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub bearing.



Result:
Proceed to
NEXT




NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 509

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC output. A
DTC not output. B


Chassis > ABS/VSC/TRC > Trouble Codes
50001 509


A

B

END