Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/ Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196262 SFI SYSTEM(w/ Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/ Air Fuel Ratio Sensor)  P2A00  A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)  


DESCRIPTION

Refer to DTC P2195.

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>P2195

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) The calculated value for the air fuel ratio sensor response rate deterioration level is less than the threshold (2 trip detection logic).
·

Air fuel ratio sensor

·

Intake system

·

Fuel injector assembly

·

Fuel pump

·

Fuel line

·

EGR valve assembly

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

Performing this confirmation driving pattern will activate the air fuel ratio sensor response monitor.


A295461E01
1.313,0.875 1.583,0.5 1.583,0.5 1.75,0.5 false 0.333,0.167 1.281,0.365 0.948,0.198 10 Vehicle Speed 1.802,0.417 3.458,0.604 1.656,0.188 10 Between 75 and 100 km/h 0.781,1.156 1.313,1.333 0.531,0.177 10 60 km/h 0.948,2.188 1.333,2.365 0.385,0.177 10 Idling 0.198,2.479 1.313,2.667 1.115,0.188 10 Ignition Switch off 1.781,2.698 2.573,2.885 0.792,0.188 10 Warming up 2.969,2.729 4.198,2.917 1.229,0.188 10 10 minutes or more 5.531,2.729 6.76,2.917 1.229,0.188 10 10 minutes or more 2.042,2.115 2.271,2.292 0.229,0.177 10 [A] 3.458,1.271 3.688,1.448 0.229,0.177 10 [B] 4.375,3.135 4.604,3.313 0.229,0.177 10 [C] 6.01,0.896 6.24,1.073 0.229,0.177 10 [D] 6.75,3.135 6.979,3.313 0.229,0.177 10 [E]

1.

Connect the GTS or Techstream to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS or Techstream on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS or Techstream on.

7.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].

8.

Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more in a city area [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / EFI / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for 10 minutes [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


12.

Enter the following menus: Powertrain / EFI / Trouble Codes [E].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

DTC P2A00 may be also stored when the air fuel ratio is stuck at rich or lean.

·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Read freeze frame data using the GTS or Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P2A00 is output A
DTC P2A00 and other DTCs are output B


HINT:

If any DTCs other than P2A00 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (INJECTION VOLUME)

B

2.PERFORM ACTIVE TEST USING GTS OR TECHSTREAM (INJECTION VOLUME)
a.

Connect the GTS or Techstream to the DLC3.


b.

Start the engine.


c.

Turn the GTS or Techstream on.


d.

Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.


e.

Enter the following menus: Powertrain / EFI / Active Test / Injection volume / All Data / AFS Voltage B1S1 and O2S B1S2.


f.

Perform the Injection volume operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and No. 2 oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS or Techstream.

HINT:
·

The Injection volume operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.

·

The air fuel ratio sensor has an output delay of a few seconds and the No. 2 oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



GTS or Techstream Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
12.5% Rich Below 3.1 V
-12.5% Lean Higher than 3.4 V
O2S B1S2
(Heated oxygen)
12.5% Rich Higher than 0.55 V
-12.5% Lean Below 0.4 V

Result:
Status of AFS Voltage B1S1 Status of O2S B1S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to
Lean/Rich Lean/Rich Normal A
Lean Lean Actual air fuel ratio lean B
Rich Rich Actual air fuel ratio rich
Lean Lean/Rich Air fuel ratio sensor malfunction C
Rich Lean/Rich Air fuel ratio sensor malfunction


Lean: During the Injection volume Active Test, the air fuel ratio sensor output voltage (AFS Voltage B1S1) is consistently higher than 3.4 V, and the No. 2 oxygen sensor output voltage (O2S B1S2) is consistently below 0.4 V.

Rich: During the Injection volume Active Test, the AFS Voltage B1S1 is consistently below 3.1 V, and the O2S B1S2 is consistently higher than 0.55 V.

Lean/Rich: During the Injection volume Active Test, the output voltage of the air fuel ratio sensor and the No. 2 oxygen sensor alternates correctly.

HINT:

Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2].

Click hereEngine / Hybrid System>2NR-VE ENGINE CONTROL>SFI SYSTEM(w/ Air Fuel Ratio Sensor)>DATA LIST / ACTIVE TEST




A

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)

B

4.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

C

8.REPLACE AIR FUEL RATIO SENSOR
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS or Techstream on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / EFI / Trouble Codes.


k.

Read the DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P2A00 is output B



A

B

8.REPLACE AIR FUEL RATIO SENSOR
4.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

OK

5.CHECK INTAKE SYSTEM

NG

5.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>2NR-VE INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks in the intake system.



Result:
Proceed to
OK
NG



OK

6.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

6.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

7.INSPECT FUEL INJECTOR ASSEMBLY

NG

10.INSPECT FUEL PUMP
7.INSPECT FUEL INJECTOR ASSEMBLY
a.

Inspect the fuel injector assembly.

Click hereEngine / Hybrid System>2NR-VE FUEL>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

8.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY

8.REPLACE AIR FUEL RATIO SENSOR
a.

Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00)
a.

Connect the GTS or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS or Techstream on.


d.

Clear the DTCs.


e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS or Techstream on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / EFI / Trouble Codes.


k.

Read the DTCs.


Result:
Result Proceed to
DTC P2A00 is output A
DTC is not output B



A

REPLACE ECM

B

END

10.INSPECT FUEL PUMP
a.

Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE FUEL LINE

NG