Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2016.09
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0288382 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1235/25  Abnormal Cycle of FR Wheel  C1236/26  Abnormal Cycle of FL Wheel  C1238/27  Abnormal Cycle of RR Wheel  C1239/28  Abnormal Cycle of RL Wheel  


DESCRIPTION

These DTCs are output when foreign material is present on the speed sensor tip or in the sensor rotor, or a chipped rotor tooth is detected.

The skid control ECU (brake actuator assembly) detects the presence of foreign material by judging from abnormal waveforms input from each speed sensor.

These DTCs may be output when the connectors of the speed sensor circuit malfunction, or there is a wire harness failure.

If DTCs relating to abnormal cycle of FR, FL, RR or RL wheel errors, and the DTCs relating to speed sensor errors (C0200/21, C0205/22, C0210/23, and C0215/24) are output at the same time, perform troubleshooting for the speed sensor first.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C1235/25 Abnormal Cycle of FR Wheel
·

When driving at higher speeds than a set speed, abnormal wheel speed signal (no pulse, abnormal value) from each wheel is detected due to disturbance noise in the speed sensor or sensor rotor malfunction, etc.

·

When driving at higher speeds than a set speed, the ABS control maintains the specified value.


·

Sensor rotor abnormality (foreign material, damage)

·

Foreign material on speed sensor

·

Open or short of speed sensor

·

Wire harness or connector

·

Improperly connected connector, deformation or corrosion of terminals

·

Interconnect resistance in speed sensor circuit wiring

·

Skid control ECU (brake actuator assembly)

·

Tire deformation

·

Brake abnormality


-
C1236/26 Abnormal Cycle of FL Wheel
·

When driving at higher speeds than a set speed, abnormal wheel speed signal (no pulse, abnormal value) from each wheel is detected due to disturbance noise in the speed sensor or sensor rotor malfunction, etc.

·

When driving at higher speeds than a set speed, the ABS control maintains the specified value.


·

Sensor rotor abnormality (foreign material, damage)

·

Foreign material on speed sensor

·

Open or short of speed sensor

·

Wire harness or connector

·

Improperly connected connector, deformation or corrosion of terminals

·

Interconnect resistance in speed sensor circuit wiring

·

Skid control ECU (brake actuator assembly)

·

Tire deformation

·

Brake abnormality


-
C1238/27 Abnormal Cycle of RR Wheel
·

When driving at higher speeds than a set speed, abnormal wheel speed signal (no pulse, abnormal value) from each wheel is detected due to disturbance noise in the speed sensor or sensor rotor malfunction, etc.

·

When driving at higher speeds than a set speed, the ABS control maintains the specified value.


·

Sensor rotor abnormality (foreign material, damage)

·

Foreign material on speed sensor

·

Open or short of speed sensor

·

Wire harness or connector

·

Improperly connected connector, deformation or corrosion of terminals

·

Interconnect resistance in speed sensor circuit wiring

·

Skid control ECU (brake actuator assembly)

·

Tire deformation

·

Brake abnormality


-
C1239/28 Abnormal Cycle of RL Wheel
·

When driving at higher speeds than a set speed, abnormal wheel speed signal (no pulse, abnormal value) from each wheel is detected due to disturbance noise in the speed sensor or sensor rotor malfunction, etc.

·

When driving at higher speeds than a set speed, the ABS control maintains the specified value.


·

Sensor rotor abnormality (foreign material, damage)

·

Foreign material on speed sensor

·

Open or short of speed sensor

·

Wire harness or connector

·

Improperly connected connector, deformation or corrosion of terminals

·

Interconnect resistance in speed sensor circuit wiring

·

Skid control ECU (brake actuator assembly)

·

Tire deformation

·

Brake abnormality


-

DTC Detection Conditions: C1235/25
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When driving at higher speeds than a set speed. ○ ○
Malfunction Status Abnormal wheel speed signal (no pulse, abnormal value) from each wheel due to disturbance noise in the speed sensor or sensor rotor malfunction, etc. ○ -
ABS control maintains the specified value. - ○
Detection Time - -
Number of Trips - -

DTC Detection Conditions: C1236/26
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When driving at higher speeds than a set speed. ○ ○
Malfunction Status Abnormal wheel speed signal (no pulse, abnormal value) from each wheel due to disturbance noise in the speed sensor or sensor rotor malfunction, etc. ○ -
ABS control maintains the specified value. - ○
Detection Time - -
Number of Trips - -

DTC Detection Conditions: C1238/27
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When driving at higher speeds than a set speed. ○ ○
Malfunction Status Abnormal wheel speed signal (no pulse, abnormal value) from each wheel due to disturbance noise in the speed sensor or sensor rotor malfunction, etc. ○ -
ABS control maintains the specified value. - ○
Detection Time - -
Number of Trips - -

DTC Detection Conditions: C1239/28
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition When driving at higher speeds than a set speed. ○ ○
Malfunction Status Abnormal wheel speed signal (no pulse, abnormal value) from each wheel due to disturbance noise in the speed sensor or sensor rotor malfunction, etc. ○ -
ABS control maintains the specified value. - ○
Detection Time - -
Number of Trips - -

CAUTION / NOTICE / HINT

NOTICE:

If the skid control ECU (brake actuator assembly) is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE


PROCEDURE

1.RECONFIRM DTC
a.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

HINT:

If DTCs relating to abnormal cycle of FR wheel / ABS consecutive operation errors, and the DTCs relating to speed sensor errors (C0200/21, C0205/22, C0210/23, and C0215/24) are output at the same time, perform troubleshooting for the speed sensor first.


Result:
Result Proceed to
DTCs relating to abnormal cycle of FR, FL, RR or RL wheel errors are output. A
DTCs relating to the speed sensor system are output at the same time B




A

2.CHECK SPEED SENSOR TIP

B

2.CHECK SPEED SENSOR TIP
a.

Turn the ignition switch off.



c.

Check the speed sensor tip.

OK:

No scratches or foreign matter on the sensor tip.


NOTICE:

Do not replace the speed sensor if no damage to the speed sensor tip is found.



HINT:
·

If the sensor is contaminated with oil or other foreign material, clean the sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction. Confirm that the rotor is not contaminated with foreign material before replacing the sensor.



Result:
Proceed to
OK
NG



OK

3.CHECK SPEED SENSOR ROTOR

NG

CLEAN OR REPLACE REAR SPEED SENSOR

3.CHECK SPEED SENSOR ROTOR
a.

Check the front axle hub bearing (front speed sensor rotor) or skid control sensor rotor.

for Front: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL

for Rear: Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT>DISASSEMBLY

HINT:
·

The front speed sensor rotor is incorporated into the front axle hub bearing.

·

If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub bearing.



Result:
Proceed to
OK
NG




OK

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - EACH SPEED SENSOR)

NG

CLEAN OR REPLACE SPEED SENSOR ROTOR

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - EACH SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness in the locking part and connecting part of the connectors.


c.

Disconnect the A13 skid control ECU (brake actuator assembly) connector.


d.

Disconnect the A31*1 or A32*2 front speed sensor and/or J2*1 or J7*2 rear speed sensor connector.

*1: for RH

*2: for LH



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
for Front RH:
Tester Connection Condition Specified Condition
A13-31 (FR1) - A31-1 (+) Always Below 1 Ω
A13-30 (FR0) - A31-2 (-) Always Below 1 Ω

for Front LH:
Tester Connection Condition Specified Condition
A13-18 (FL1) - A32-1 (+) Always Below 1 Ω
A13-17 (FL0) - A32-2 (-) Always Below 1 Ω

for Rear RH:
Tester Connection Condition Specified Condition
A13-16 (RR1) - J2-1 (+) Always Below 1 Ω
A13-15 (RR0) - J2-2 (-) Always Below 1 Ω

for Rear LH:
Tester Connection Condition Specified Condition
A13-29 (RL1) - J7-1 (+) Always Below 1 Ω
A13-28 (RL0) - J7-2 (-) Always Below 1 Ω


Standard Resistance (Check for Short):
for Front RH:
Tester Connection Condition Specified Condition
A13-31 (FR1) or A31-1 (+) - Body ground Always 10 kΩ or higher
A13-30 (FR0) or A31-2 (-) - Body ground Always 10 kΩ or higher

for Front LH:
Tester Connection Condition Specified Condition
A13-18 (FL1) or A32-1 (+) - Body ground Always 10 kΩ or higher
A13-17 (FL0) or A32-2 (-) - Body ground Always 10 kΩ or higher

for Rear RH:
Tester Connection Condition Specified Condition
A13-16 (RR1) or J2-1 (+) - Body ground Always 10 kΩ or higher
A13-15 (RR0) or J2-2 (-) - Body ground Always 10 kΩ or higher

for Rear LH:
Tester Connection Condition Specified Condition
A13-29 (RL1) or J7-1 (+) - Body ground Always 10 kΩ or higher
A13-28 (RL0) or J7-2 (-) - Body ground Always 10 kΩ or higher


NOTICE:

Check the speed sensor signal after repair or replacement (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE).


Result:
Proceed to
OK
NG




OK

5.CHECK TERMINAL VOLTAGE (POWER SOURCE TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (POWER SOURCE TERMINAL)
a.

Turn the ignition switch off.


b.
C364676C01
0.375,0.583 0.74,0.802 0.365,0.219 0.375,0.917 0.74,1.135 0.365,0.219 0.156,3.313 0.521,3.531 0.365,0.219 0.167,3.646 0.531,3.865 0.365,0.219 0.438,0.615 1,1.052 0.563,0.438 10 false A31 0.281,3.677 0.844,4.115 0.563,0.438 10 false J7 0.448,0.948 1.01,1.385 0.563,0.438 10 false A32 0.271,3.344 0.833,3.781 0.563,0.438 10 false J2 0.833,0.615 1.396,1.052 0.563,0.438 10 false *A 0.833,0.948 1.396,1.385 0.563,0.438 10 false *B 0.583,3.354 1.146,3.792 0.563,0.438 10 false *C 0.583,3.688 1.146,4.125 0.563,0.438 10 false *D 0.115,0.094 0.677,0.531 0.563,0.438 10 false *a
*A Front RH
*B Front LH
*C Rear RH
*D Rear LH
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Reconnect the A13 skid control ECU (brake actuator assembly) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A31-1 (+) - Body ground Ignition switch ON 5.7 to 14 V
A32-1 (+) - Body ground Ignition switch ON 5.7 to 14 V
J2-1 (+) - Body ground Ignition switch ON 5.7 to 14 V
J7-1 (+) - Body ground Ignition switch ON 5.7 to 14 V


Result:
Proceed to
OK
NG




OK

6.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC is output. Front speed sensor A
DTC is output. Rear speed sensor B
DTC is not output. C




A

7.REPLACE FRONT SPEED SENSOR

B

11.REPLACE REAR SPEED SENSOR

C

7.REPLACE FRONT SPEED SENSOR
a.

Turn the ignition switch off.


b.

Replace the front speed sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>FRONT SPEED SENSOR>REMOVAL

Result:
Proceed to
NEXT




NEXT

8.RECONFIRM DTC
8.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC is output. A
DTC is not output. B




A

9.REPLACE SPEED SENSOR ROTOR

B

END

9.REPLACE SPEED SENSOR ROTOR
a.

Replace the front axle hub bearing (front speed sensor rotor).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB>REMOVAL

HINT:
·

The front speed sensor rotor is incorporated into the front axle hub bearing.

·

If the front speed sensor rotor needs to be replaced, replace it together with the front axle hub bearing.



Result:
Proceed to
NEXT




NEXT

10.RECONFIRM DTC
10.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC is output. A
DTC is not output. B


HINT:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

END

11.REPLACE REAR SPEED SENSOR
a.

Turn the ignition switch off.


b.

Replace the rear speed sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL

Result:
Proceed to
NEXT




NEXT

12.RECONFIRM DTC
12.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC is output. A
DTC is not output. B




A

13.REPAIR SKID CONTROL SENSOR ROTOR

B

END

13.REPAIR SKID CONTROL SENSOR ROTOR
a.

Remove the skid control sensor rotor.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT>REMOVAL


b.

Check the rear skid control sensor rotor.

OK:

No scratches, oil or foreign matter on the rotors.



Result:
Proceed to
NEXT



NEXT

14.RECONFIRM DTC
14.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Result:
Result Proceed to
DTC is output A
DTC is not output B


HINT:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

END