Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2016.10–2019.09
RM32K0E _51 Engine / Hybrid System _059913 2ZR-FXE ENGINE MECHANICAL _0293919 CYLINDER HEAD GASKET A

2ZR-FXE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)
for SFI system

Replacement of ECM


Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
for SFI system
·

Replacement of throttle body assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of fuel injector assembly

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light/yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:
(Click here)
for Calibration:
(Click here)
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

PROCEDURE

Hide 25620 5.REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER

Hide 17167 6.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17141 8.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

Hide 15301 10.REMOVE ENGINE OIL LEVEL DIPSTICK

Hide 11452 11.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 16289 12.REMOVE NO. 5 WATER BY-PASS PIPE

Hide 1628A 13.REMOVE NO. 6 WATER BY-PASS PIPE

Hide 17650G 14.REMOVE PURGE VALVE (PURGE VSV)

Hide 23818 15.REMOVE FUEL VAPOR FEED PIPE

Hide 23807 16.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23807V 17.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23250 18.REMOVE FUEL INJECTOR ASSEMBLY

Hide 11101E 20.REMOVE CAMSHAFT POSITION SENSOR

Hide 11201 21.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11213 22.REMOVE CYLINDER HEAD COVER GASKET

Hide 11193 23.REMOVE SPARK PLUG TUBE GASKET

Hide 24.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13540 26.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 11302A 27.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 11302 28.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 13559 29.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 30.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13562 31.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13506 32.REMOVE CHAIN SUB-ASSEMBLY

a.
A374439C01
2.823,2.406 2.958,1.75 true 1.75,4.073 0.594,3.813 true 1.823,4.031 2.135,4.188 0.313,0.156 10 true *a 2.958,1.615 3.271,1.771 0.313,0.156 10 false *b
*a Loosen the chain sub-assembly
*b Place the chain sub-assembly on the non-toothed portion of camshaft timing gear assembly


Using a wrench to hold the hexagonal portion of the camshaft, turn the camshaft timing gear assembly counterclockwise to loosen the chain sub-assembly between the camshaft timing sprocket and camshaft timing gear assembly.


b.

With the chain sub-assembly loosened, separate the chain sub-assembly from the teeth of the camshaft timing gear assembly and place it on the non-toothed portion of camshaft timing gear assembly.


c.

Turn the camshaft clockwise to return it to its original position and remove the chain sub-assembly.


Hide 13050 33.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13050 34.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13523G 35.REMOVE CAMSHAFT TIMING SPROCKET

Hide 11103 39.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13801 40.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 41.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 43.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 44.REMOVE CYLINDER HEAD GASKET

a.
A374457

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 45.INSPECT CYLINDER HEAD SET BOLT