Home › Engine / Hybrid System › 3ZR-FAE (ENGINE CONTROL) › SFI SYSTEM
RM32H0E _51 Engine / Hybrid System _059607 3ZR-FAE ENGINE CONTROL _0292315 SFI SYSTEM C

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  P0300  Random / Multiple Cylinder Misfire Detected  P0301  Cylinder 1 Misfire Detected  P0302  Cylinder 2 Misfire Detected  P0303  Cylinder 3 Misfire Detected  P0304  Cylinder 4 Misfire Detected  


DESCRIPTION

When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0300 Random / Multiple Cylinder Misfire Detected Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*

*: The MIL flashes when a catalyst-damaging misfire is detected.


DTC stored
P0301 Cylinder 1 Misfire Detected Misfiring of the No. 1 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*

*: The MIL flashes when a catalyst-damaging misfire is detected.


DTC stored
P0302 Cylinder 2 Misfire Detected Misfiring of the No. 2 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*

*: The MIL flashes when a catalyst-damaging misfire is detected.


DTC stored
P0303 Cylinder 3 Misfire Detected Misfiring of the No. 3 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*

*: The MIL flashes when a catalyst-damaging misfire is detected.


DTC stored
P0304 Cylinder 4 Misfire Detected Misfiring of the No. 4 cylinder occurs and one of the following conditions is met (2 trip detection logic):
·

A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).

·

An emission deterioration misfire occurs (MIL illuminates).


·

Open or short in engine wire harness

·

Connector connection

·

Vacuum hose connections

·

Ignition system

·

Fuel injector assembly

·

Fuel pressure

·

Mass air flow meter

·

Engine coolant temperature sensor

·

Compression pressure

·

Valve timing

·

PCV valve and hose

·

PCV hose connections

·

Intake system

·

ECM


Comes on/Blinks*

*: The MIL flashes when a catalyst-damaging misfire is detected.


DTC stored

When DTCs for misfiring cylinders are randomly stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION

The ECM illuminates the MIL and stores a DTC when the following condition, which could cause catalyst deterioration, is detected (2 trip detection logic).

·

An excessive misfiring rate (approximately 70 to 100 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.


The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.

·

A sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.


MONITOR STRATEGY

Required Sensors/Components (Main) Crankshaft position sensor
Camshaft position sensor
Required Sensors/Components (Related) Engine coolant temperature
Intake air temperature sensor
Mass air flow meter
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Misfire
Intake air temperature Higher than -10°C (14°F)
Either of the following conditions is met (a) or (b)
(a) Engine coolant temperature at engine start Higher than -7°C (19°F)
(b) Engine coolant temperature Higher than 20°C (68°F)

Monitor Period of Emission-related Misfire
Duration Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-damaging Misfire (MIL Blinks)
Duration Crankshaft 200 revolutions x 3

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Record the DTC(s) and freeze frame data.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Switch the ECM from normal mode to check mode.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>CHECK MODE PROCEDURE

7.

Read the misfire counts of each cylinder, Cylinder #1 Misfire Count to Cylinder #4 Misfire Count, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.

8.

Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the freeze frame data. Perform this step several times.

HINT:
·

In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, using the Misfire RPM and Misfire Load in the Data List.


Engine Speed (rpm) Duration
Idling 8.0 minutes or more
1000 4.5 minutes or more
2000 2.5 minutes or more
3000 1.5 minutes or more


9.

Check whether misfires have occurred by checking DTCs and freeze frame data.

HINT:

Do not turn the ignition switch off until the stored DTC(s) and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), freeze frame data and other data will be cleared.


10.

Record the DTC(s), freeze frame data and misfire counts.

11.

Turn the ignition switch off and wait for at least 30 seconds.

12.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).


CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Check the "Fuel Cut Elps Time" in the Data List or the Freeze Frame Data.

If the elapsed time is over 0 seconds, then the engine speed is high (engine speed at which fuel cut occurs + 500 rpm).

When this has happened, there is the possibility that the valve rocker arm will become loose and a fire could start, so check that the valve rocker arm is properly attached.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE MECHANICAL)>CAMSHAFT>REMOVAL

·

By clearing the DTC, "Fuel Cut Elps Time" will be cleared.

·

If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.

·

If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors is considered to be a possible cause of the problem:

(a)

There was insufficient fuel in the tank.

(b)

Improper fuel was used.

(c)

The spark plugs have been contaminated.

(d)

The problem requires further diagnosis.


·

After finishing repairs, check the misfire counts of the cylinders (Cylinder #1 Misfire Count to Cylinder #4 Misfire Count).

·

Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.

·

When one of Short FT #1 or Long FT #1 in the freeze frame data is outside the range of +/-15%, the air fuel ratio may be rich (-15% or less) or lean (+15% or more).

·

When Coolant Temp in the freeze frame data is less than 75°C (167°F), the misfires have occurred only while warming up the engine.

·

An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.

·

In the past, when the primary ignition system (the igniter drive circuit in the ECM, the primary circuit in the No. 1 ignition coil, the related wire harness, or the connector) was out of order, diagnostic codes from P0351 to P0354 were output. However, these codes are not output in this vehicle.

When a failure in the primary ignition system is suspected, refer to "Cat OT MF F/C History", "Cat OT MF F/C Cylinder #1 to #4", and "Cylinder #1 Misfire Count to Cylinder #4 Misfire Count" in the freeze frame data, the pending freeze frame data, and the Data List, and confirm in which cylinder the high-frequency misfire was concentrated.

·

Referring to the following contents of the freeze frame data (or the pending freeze frame data) enables an estimation of which cylinder has misfired and to what degree.

-

Cylinder #1 Misfire Count to Cylinder #4 Misfire Count: Misfire count according to cylinder.

-

Cat OT MF F/C Cylinder #1 to #4: This expresses a high-frequency misfire was concentrated in a certain cylinder and that cylinder's fuel injection was stopped.




PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs.

Result:
Result Proceed to
DTC P0300, P0301, P0302, P0303 and/or P0304 are output A
DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output B



HINT:

If any DTCs other than P0300, P0301, P0302, P0303 and P0304 are output, troubleshoot those DTCs first.



A

2.CHECK PCV HOSE CONNECTIONS

B

2.CHECK PCV HOSE CONNECTIONS
a.

Check the PCV hose connections.

Click hereEngine / Hybrid System>3ZR-FAE (EMISSION CONTROL)>PCV VALVE>COMPONENTS

OK:

PCV valve and hose are correctly connected and are not damaged.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)

NG

3.READ VALUE USING GTS (MISFIRE RPM AND MISFIRE LOAD)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Misfire RPM and Misfire Load.

Powertrain > Engine and ECT > Data List
Tester Display
Misfire RPM
Misfire Load
50003 234 319,320

e.

Read and note the Misfire RPM and Misfire Load values.

HINT:

The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.



Result:
Proceed to
NEXT



NEXT

4.READ FREEZE FRAME DATA (CAT OT MF F/C HISTORY)
4.READ FREEZE FRAME DATA (CAT OT MF F/C HISTORY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Using the GTS, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>FREEZE FRAME DATA


Result:
Freeze Frame Data Item Result Proceed to
Cat OT MF F/C History ON A
OFF B



A

5.INSPECT SPARK PLUG

B

7.PERFORM ACTIVE TEST USING GTS (PROHIBIT THE CATALYST OT MISFIRE PREVENT F/C)
5.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

6.CHECK FOR SPARKS (SPARK TEST)

NG

6.CHECK FOR SPARKS (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

7.PERFORM ACTIVE TEST USING GTS (PROHIBIT THE CATALYST OT MISFIRE PREVENT F/C)
7.PERFORM ACTIVE TEST USING GTS (PROHIBIT THE CATALYST OT MISFIRE PREVENT F/C)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.

Powertrain > Engine and ECT > Active Test
Tester Display
Prohibit the Catalyst OT Misfire prevent F/C
50004 234 155

f.

Perform the Active Test.

NOTICE:

When performing the Active Test, make sure the vehicle is stopped and the engine is either idling or being revved within 3000 rpm.



Result:
Proceed to
NEXT



NEXT

8.READ VALUE USING GTS (CYLINDER MISFIRE COUNT)
8.READ VALUE USING GTS (CYLINDER MISFIRE COUNT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 Misfire Count, Cylinder #2 Misfire Count, Cylinder #3 Misfire Count and Cylinder #4 Misfire Count.

Powertrain > Engine and ECT > Data List
Tester Display
Cylinder #1 Misfire Count
Cylinder #2 Misfire Count
Cylinder #3 Misfire Count
Cylinder #4 Misfire Count
50003 234 321,322,323,324

e.

Start the engine and allow the engine to idle.


f.

Read each value for Cylinder #1 Misfire Count to Cylinder #4 Misfire Count displayed on the GTS. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.

1.

Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using GTS (Misfire RPM and Misfire Load)" procedures above [A].

2.

Read the Cylinder #1 Misfire Count to Cylinder #4 Misfire Count or DTCs displayed on the GTS [B].


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:
·

If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.

·

If the freeze frame data record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.

·

If the freeze frame data record of the Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.




Result:
Result Proceed to
Most misfires occur in only 1 or 2 cylinders A
3 cylinders or more have equal misfire counts B



A

9.INSPECT SPARK PLUG

B

20.CHECK INTAKE SYSTEM
9.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

10.CHECK FOR SPARK (SPARK TEST)

NG

10.CHECK FOR SPARK (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

11.CHECK CYLINDER COMPRESSION PRESSURE
11.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

12.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

12.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)
a.
A396015C01
1.333,0.333 1.833,0.583 0.5,0.25 2.969,2.781 2.594,1.333 true 2.417,2.802 2.01,1.469 true 1.833,2.854 1.938,1.479 true 0.667,2.906 1.792,1.469 true 1.219,2.844 1.865,1.479 true 1.469,0.375 1.927,0.573 0.458,0.198 10 false C63 2.906,2.833 3.365,3.031 0.458,0.198 10 false E01 2.375,2.875 2.833,3.073 0.458,0.198 10 false #10 1.719,2.875 2.177,3.073 0.458,0.198 10 false #40 1.115,2.896 1.573,3.094 0.458,0.198 10 false #30 0.573,2.917 1.031,3.115 0.458,0.198 10 false #20 0.104,0.083 0.479,0.323 0.375,0.24 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C63-98 (#10) - C63-57 (E01) Ignition switch ON 11 to 14 V
C63-95 (#20) - C63-57 (E01) Ignition switch ON 11 to 14 V
C63-96 (#30) - C63-57 (E01) Ignition switch ON 11 to 14 V
C63-97 (#40) - C63-57 (E01) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

13.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER

NG

13.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
a.

Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>3ZR-FAE (FUEL)>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repairs" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

14.CHECK INTAKE SYSTEM

NG

REPLACE FUEL INJECTOR ASSEMBLY

14.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>3ZR-FAE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

15.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

15.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

16.READ VALUE USING GTS (COOLANT TEMP)

NG

36.CHECK FUEL LINE
16.READ VALUE USING GTS (COOLANT TEMP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

e.

Read the Data List twice, when the engine is both cold and warmed up.

Standard:
GTS Display Condition Specified Condition
Coolant Temp Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

17.READ VALUE USING GTS (MAF)

NG

17.READ VALUE USING GTS (MAF)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
MAF
Coolant Temp
50003 234 9,3,8

e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read MAF with the engine speed at 3000 rpm.

Standard:
GTS Display Condition Specified Condition
MAF Shift lever position: P or N
A/C: Off
Engine Speed: 3000 rpm
Between 5.0 gm/sec and 10.0 gm/sec



Result:
Proceed to
OK
NG



OK

18.CHECK ENGINE MECHANICAL SYSTEM

NG

31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
18.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY

Result:
Proceed to
OK
NG




OK

19.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 OR P0304)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

19.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 OR P0304)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine.


i.

Warm up the engine.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

l.

Input the DTC: P0300, P0301, P0302, P0303 or P0304.


m.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output)
B




A

END

B

31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
20.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks.

Click hereEngine / Hybrid System>3ZR-FAE (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION

OK:

No leaks from intake system.


HINT:

Perform "Inspection After Repair" after repairing or replacing the intake system.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

21.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE INTAKE SYSTEM

21.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

22.READ VALUE USING GTS (COOLANT TEMP)

NG

36.CHECK FUEL LINE
22.READ VALUE USING GTS (COOLANT TEMP)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.

Powertrain > Engine and ECT > Data List
Tester Display
Coolant Temp
50003 234 8

e.

Read the Data List twice, when the engine is both cold and warmed up.

Standard:
GTS Display Condition Specified Condition
Coolant Temp Cold engine Same as ambient air temperature
Warm engine Between 75 and 100°C (167 and 212°F)


HINT:

Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

23.READ VALUE USING GTS (MAF)

NG

23.READ VALUE USING GTS (MAF)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
MAF
Coolant Temp
50003 234 9,3,8

e.

Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.


f.

Read MAF with the engine speed at 3000 rpm.

Standard:
GTS Display Condition Specified Condition
MAF Shift lever position: P or N
A/C: Off
Engine Speed: 3000 rpm
Between 5.0 gm/sec and 10.0 gm/sec



Result:
Proceed to
OK
NG



OK

24.INSPECT SPARK PLUG

NG

31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
24.INSPECT SPARK PLUG
a.

Inspect the spark plug of the misfiring cylinder.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the spark plug.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

25.CHECK FOR SPARKS (SPARK TEST)

NG

25.CHECK FOR SPARKS (SPARK TEST)
a.

Perform a spark test.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION

HINT:
·

If the result of the spark test is normal, proceed to the next step.

·

Perform "Inspection After Repair" after repairing or replacing the ignition system.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

26.CHECK CYLINDER COMPRESSION PRESSURE
26.CHECK CYLINDER COMPRESSION PRESSURE
a.

Measure the cylinder compression pressure of the misfiring cylinder.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION

HINT:

Perform "Inspection After Repair" after repairing or replacing the engine assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

27.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

27.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40)
a.
A396015C01
1.333,0.333 1.833,0.583 0.5,0.25 2.969,2.781 2.594,1.333 true 2.417,2.802 2.01,1.469 true 1.833,2.854 1.938,1.479 true 0.667,2.906 1.792,1.469 true 1.219,2.844 1.865,1.479 true 1.469,0.375 1.927,0.573 0.458,0.198 10 false C63 2.906,2.833 3.365,3.031 0.458,0.198 10 false E01 2.375,2.875 2.833,3.073 0.458,0.198 10 false #10 1.719,2.875 2.177,3.073 0.458,0.198 10 false #40 1.115,2.896 1.573,3.094 0.458,0.198 10 false #30 0.573,2.917 1.031,3.115 0.458,0.198 10 false #20 0.104,0.083 0.479,0.323 0.375,0.24 10 false *a
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C63-98 (#10) - C63-57 (E01) Ignition switch ON 11 to 14 V
C63-95 (#20) - C63-57 (E01) Ignition switch ON 11 to 14 V
C63-96 (#30) - C63-57 (E01) Ignition switch ON 11 to 14 V
C63-97 (#40) - C63-57 (E01) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

28.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER

NG

28.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER
a.

Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>3ZR-FAE (FUEL)>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

29.CHECK ENGINE MECHANICAL SYSTEM

NG

REPLACE FUEL INJECTOR ASSEMBLY

29.CHECK ENGINE MECHANICAL SYSTEM
a.

Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY

Result:
Proceed to
OK
NG




OK

30.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 OR P0304)

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

30.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303 OR P0304)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine.


i.

Warm up the engine.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

l.

Input the DTC: P0300, P0301, P0302, P0303 or P0304.


m.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output)
B




A

END

B

31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER CONNECTOR CONNECTION)
a.

Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE

HINT:

Repair any problems.



Result:
Proceed to
NEXT



NEXT

32.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
32.CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine.


i.

Warm up the engine.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

l.

Input the DTC: P0300, P0301, P0302, P0303 or P0304.


m.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output)
B




A

END

B

33.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
33.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the C5 mass air flow meter connector.


b.

Disconnect the C63 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C5-1 (FG) - C63-137 (VG) Always Below 1 Ω
C5-2 (E2G) - C63-104 (E2G) Always Below 1 Ω
C5-1 (FG) or C63-137 (VG) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

34.REPLACE MASS AIR FLOW METER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW METER - ECM)

34.REPLACE MASS AIR FLOW METER
a.

Replace the mass air flow meter.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>MASS AIR FLOW METER>REMOVAL

HINT:
·

If the results of the inspections performed in steps 13 and 19 indicated no problem, proceed to the next step without replacing the mass air flow meter.

·

Perform "Inspection After Repair" after replacing the mass air flow meter.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




Result:
Proceed to
NEXT



NEXT

35.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
35.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine.


i.

Warm up the engine.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

Powertrain > Engine and ECT > Utility
Tester Display
All Readiness
50005 234 20

l.

Input the DTC: P0300, P0301, P0302, P0303 or P0304.


m.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTC is not output)
A
ABNORMAL
(DTC P0300, P0301, P0302, P0303 or P0304 is output)
B




A

END

B

36.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE FUEL LINE