ENTRY AND START SYSTEM > Engine does not Start |
| ENGINE START SYSTEM FUNCTION |
If the engine switch is pressed with the shift lever in the P or N position and the brake pedal depressed, the main body ECU determines that it is an engine start request.
The certification ECU and other ECUs perform key verification via the LIN communication line.
The main body ECU activates the ACC relay.
The main body ECU activates the IG1 and IG2 relays.
The certification ECU outputs a steering UNLOCK signal. The signal is sent to the main body ECU via the steering lock ECU.
The main body ECU sends an engine start request signal to the ECM.
The ECM sends an ACC cut request signal to the main body ECU.
The ECM and main body ECU activate the ST relay.
The main body ECU deactivates the ACC relay until the ECU detects an engine start.
When engine revolution speed reaches 1200 rpm, the ECM determines that the engine has been started.
The ECM stop sending an ACC cut request signal to the main body ECU.
The main body ECU reactivates the ACC relay and turns off the engine switch indicator light, when engine revolution speed reaches 800 rpm.
| Symbols of main body ECU | Signals |
| STP | Stop light switch ON signal |
| SSW1/SSW2 | Engine switch ON signal |
| ACCD | ACC relay operation signal |
| IG2D | IG2 relay operation signal |
| STR2 | ST relay operation signal |
| STR | Park/neutral position switch signal |
| TACH | Engine start detection signal |
| STSW | Starter activation request signal |
| ACCR | ACC cut request signal |


| EMERGENCY ENGINE START CONTROL |
If there is a malfunction in the stop light switch or STOP fuse, their signals may not be correctly transmitted to the main body ECU. This may result in the engine not starting even if the engine switch is pressed while the brake pedal is depressed and the shift lever is in the P position.
To activate the starter:
Turn the engine switch from off to on (ACC).
Press and hold the engine switch for 15 seconds.
| 1.CHECK ENTRY FUNCTION DETECTION AREA |
![]() |
Inspect entry detection area.
When the electrical key is in either of the 2 inspection points in the illustration, the shift lever is in the P position and the brake pedal is depressed, check that the engine switch indicator illuminates in green.
|
| ||||
| OK | |
| Go to step 3 |
| 2.CHECK FOR DTC |
Delete the DTCs (Click here).
Check for DTCs again.
|
| ||||
| OK | |
| Go to step 4 |
| 3.CHECK ENGINE SWITCH CONDITION |
Check the power source mode change.
When the key is inside the vehicle and the shift lever is in the P position, check that pressing the engine switch causes the power source mode to change as follows:
|
| ||||
| OK | |
| 4.CHECK CRANKING FUNCTION |
Check the engine cranking function.
When there is fuel in the fuel tank, the key is inside the vehicle, and the shift lever is in the P position, check that depressing the brake pedal and pressing the engine switch crank the engine.
|
| ||||
| NG | |
| 5.READ VALUE USING INTELLIGENT TESTER (P SIGNAL) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Body / Data List.
Read the Data List according to the displays on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Shift P Sig | Shift P signal / ON or OFF | ON: Shift position is P OFF: Shift position is not P | - |
|
| ||||
| OK | |
| 6.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH) |
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light SW | Stop light Switch / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
|
| ||||
| OK | |
| 7.READ VALUE USING INTELLIGENT TESTER (STEERING LOCK) |
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Str Unlock SW | Steering lock condition / ON or OFF | ON: Steering is unlocked (Engine switch on (ACC)) OFF: Steering is locked (Engine switch off) | - |
|
| ||||
| OK | |
| 8.CHECK STEERING LOCK |
Check if the steering lock is released when turning the engine switch on (ACC).
|
| ||||
| OK | |
| 9.INSPECT MAIN BODY ECU (STSW VOLTAGE) |
![]() |
Disconnect the A55 ECM connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E9-4 (STSW) - Body ground | Brake pedal depressed, engine switch held on (ST) | Output voltage at terminal AM1 or AM2 is -2 V or more. |
|
| ||||
| OK | |
| 10.INSPECT ECM (ACCR VOLTAGE) |
![]() |
Reconnect the connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E6-3 (ACCR) - IM-9 (GND2) | Brake pedal depressed, shift lever P position, engine switch is pushed once → on (IG) | 0.1 to 0.8 V*1 → Output voltage at terminal AM1 or AM2 is -2 V or more. |
|
| ||||
| OK | |
| 11.INSPECT ECM (STR2 VOLTAGE) |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E9-6 (STR2) - IM-9 (GND2) | Brake pedal depressed, shift lever P or N position, engine switch on (ST) | Output voltage at terminal AM1 or AM2 is -3.5 V or more.*1 |
|
| ||||
| OK | |
| 12.CHECK WIRE HARNESS (MAIN BODY ECU -ECM - ENGINE ROOM R/B) |
Remove the ST CUT relay from the engine room R/B.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C55-63 (STAR) - E9-6 (STR2)*1 C58-63 (STAR) - E9-6 (STR2)*2 | Always | Below 1 Ω |
| C55-63 (STAR) - ST CUT relay terminal - 3*1 C58-63 (STAR) - ST CUT relay terminal - 3*2 | Always | Below 1 Ω |
| C55-63 (STAR) - Body ground*1 C58-63 (STAR) - Body ground*2 | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 13.INSPECT RELAY (ST CUT) |
![]() |
Measure the resistance of the ST CUT relay.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | When battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | When battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 14.INSPECT PARK/NEUTRAL POSITION SWITCH |
![]() |
Disconnect the park/neutral position (PNP) switch connector.
Measure the resistance according the the value(s) in the table below.
| Shift Position | Tester Connection | Specified Condition |
| P | 4 - 9 | Below 1 Ω |
| N | 4 - 9 | Below 1 Ω |
| Except P and N | 4 - 9 | 10 kΩ or higher |
|
| ||||
| OK | |
| 15.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
Disconnect the C55*1 or C58*2 ECM connector.

Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C55-62 (NSW) - C1-4*1 C58-62 (NSW) - C1-4*2 | Always | Below 1 Ω |
| C55-62 (NSW) - Body ground*1 C58-62 (NSW) - Body ground*2 | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 16.INSPECT RELAY (ST) |
![]() |
Remove the starter relay from the engine room R/B.
Measure the resistance of the starter relay.
| Tester Connection | Condition | Specified Condition |
| 3 - 5 | When battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | when battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
|
| ||||
| OK | |
| 17.CHECK HARNESS AND CONNECTOR (ECM AND STARTER - ST RELAY) |
Disconnect the A55*1 or A24*2 ECM connector.

Disconnect the C3 starter connector.
Measure the resistance according the the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A55-48 (STA) - ST relay terminal - 1*1 A24-48 (STA) - ST relay terminal - 1*2 | Always | Below 1 Ω |
| A55-48 (STA) - Body ground*1 A24-48 (STA) - Body ground*2 | Always | 10 kΩ or higher |
| C3-1 - ST relay terminal - 3 | Always | Below 1 Ω |
| C3-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 18.INSPECT ENGINE ROOM RELAY BLOCK (ST RELAY VOLTAGE) |
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| ST relay terminal - 5 - Body ground | Always | 9 to 14 V |
|
| ||||
| OK | |
| 19.INSPECT STARTER ASSEMBLY |
|
| ||||
| OK | ||
| ||
| 20.READ VALUE USING INTELLIGENT TESTER (L CODE) |
Reconnect the connectors.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Entry & Start / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| L Code Chk | L code check / ON or NG | OK: Normal NG: Malfunction | Electrical key in the cabin |
|
| ||||
| OK | |
| 21.READ VALUE USING INTELLIGENT TESTER (ENGINE START REQUEST) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Start Rqst-Past | Start request signal response / OK or NG | OK: Received NG: Not received | - |
|
| ||||
| OK | |
| 22.READ VALUE USING INTELLIGENT TESTER (S CODE) |
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| S Code Chk | S code check / OK or NG | OK: Normal NG: Malfunction | - |
|
| ||||
| OK | |
| 23.INSPECT ID CODE BOX |
![]() |
Check the input signal waveform.
Connect an oscilloscope to terminal E68-6 (EFIO) and body ground.
Turn the engine switch on (IG).
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
| Tool setting | 10 V/DIV., 100 ms./DIV. |
| Vehicle condition | Engine switch on (IG) |
|
| ||||
| OK | ||
| ||