Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge) › from 2015.04
RM19V0EQ _53 Suspension _014588 FRONT SUSPENSION _0281054 FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge) A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER(When Using the Engine Support Bridge)  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 3.SECURE STEERING WHEEL

Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 5.REMOVE FRONT WHEELS

Hide 53852K 6.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH (for RHD)

Hide 51442C 7.REMOVE ENGINE UNDER COVER LH

Hide 53851Z 8.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)

Hide 51441C 9.REMOVE ENGINE UNDER COVER RH

Hide 53737B 10.REMOVE FRONT FENDER APRON SEAL LH

Hide 53736 11.REMOVE FRONT FENDER APRON SEAL RH

Hide 53295E 12.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 12601B 13.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 17750A 14.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 17735 15.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17801 16.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17701 17.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 17771A 20.REMOVE NO. 1 AIR CLEANER BRACKET

Hide 17410 21.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 43502H 22.REMOVE FRONT AXLE SHAFT NUT LH

Hide 43501H 23.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Perform the same procedure as for the LH side.


Hide 48810 24.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 25.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45470 26.SEPARATE TIE ROD ASSEMBLY LH

Hide 45460 27.SEPARATE TIE ROD ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48069 28.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 29.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 43420 30.SEPARATE FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 31.SEPARATE FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45220 32.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 12361A 33.SEPARATE FRONT ENGINE MOUNTING INSULATOR

a.
A209884

Remove the 3 nuts and separate the front engine mounting insulator from the front frame assembly.


Hide 12372A 34.SEPARATE ENGINE MOUNTING INSULATOR LH

a.

Remove the 2 hole plugs.


b.
A353344

Remove the 3 nuts and separate the engine mounting insulator LH from the front frame assembly.


Hide 12362 35.SEPARATE ENGINE MOUNTING INSULATOR RH

a.

Remove the 2 hole plugs.


b.
A209885

Remove the 3 nuts and separate the engine mounting insulator RH from the front frame assembly.


Hide 12327A 36.REMOVE NO. 2 ENGINE MOUNTING STAY RH

Hide 37.INSTALL ENGINE HANGERS

a.
A195856C14
0.313,2.125 0.479,2.125 0.479,2.125 0.813,1.625 false 3.01,2.094 2.865,2.094 2.865,2.094 2.479,1.323 false 0.156,2.052 0.365,2.24 0.208,0.188 10 false *1 3.052,2.01 3.26,2.198 0.208,0.188 10 false *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the 2 engine hangers with the 2 bolts as shown in the illustration.

Part No.
Item Part No.
No. 1 engine hanger 12281-36020
No. 2 engine hanger 12282-36021
Bolt 91552-81040 or 91552-81025

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 38.INSTALL ENGINE SUPPORT BRIDGE

a.

Remove the 2 hood support assemblies.

Click hereVehicle Exterior>DOOR / HATCH>HOOD SUPPORT>REMOVAL


b.

Install SST to the vehicle body as shown in the illustration.

C316204C01
5.781,2.729 6.563,2.729 true 4.698,2.406 4.927,2.406 4.927,2.406 5.125,2.656 true 2.417,2.344 2.198,2.344 2.198,2.344 2.083,2.469 true 4.271,5.948 5.531,5.948 true 1.708,5.896 2.781,5.896 true 1.198,8.177 1.198,7.76 1.198,7.76 1.365,7.76 false 5.188,7.021 5.385,7.021 5.385,7.021 5.615,6.76 true 1.958,7.021 1.781,7.021 1.781,7.021 1.667,6.74 true 2.375,8.188 2.375,7.771 2.375,7.771 2.219,7.771 false 5.917,8.188 5.917,7.771 5.917,7.771 5.76,7.771 false 4.813,8.188 4.813,7.771 4.813,7.771 4.927,7.771 false 2.802,5.802 2.979,5.979 0.177,0.177 10 true *a 1.406,7.688 1.719,7.844 0.313,0.156 10 false *b 2.448,2.271 2.76,2.427 0.313,0.156 10 false *c 0.938,1.885 1.25,2.042 0.313,0.156 10 false *d 0.958,7 1.271,7.156 0.313,0.156 10 false *e 2.5,6.979 2.813,7.135 0.313,0.156 10 false *f 0.479,0.948 0.625,1.156 0.146,0.208 10 true *g 4.115,5.875 4.427,6.031 0.313,0.156 10 false *a 2.073,7.708 2.385,7.865 0.313,0.156 10 false *b 4.958,7.698 5.271,7.854 0.313,0.156 10 false *b 5.615,7.708 5.927,7.865 0.313,0.156 10 false *b 6.073,6.979 6.385,7.135 0.313,0.156 10 false *e 4.552,7 4.865,7.156 0.313,0.156 10 false *f 1.99,6.938 2.302,7.094 0.313,0.156 10 false *b 5.042,6.958 5.354,7.115 0.313,0.156 10 false *b 4.531,2.333 4.708,2.51 0.177,0.177 10 true *c 6.031,1.875 6.344,2.031 0.313,0.156 10 false *d 6.458,1 6.625,1.188 0.167,0.188 10 true *g 6.604,2.646 6.948,2.823 0.344,0.177 10 false SST
*a Support Shaft *b Side Member
*c Cloth *d Front Side
*e Correct *f Incorrect
*g Front Suspension Nut - -


SST
09940-10010  

CAUTION:
·
C312303C05
1.761,2.043 1.964,2.235 0.203,0.191 10 *a 0.175,1.885 0.378,2.076 0.203,0.191 10 *a 0.57,0.075 0.773,0.266 0.203,0.191 10 *c 2.261,0.075 2.464,0.266 0.203,0.191 10 *d 0.136,2.338 0.340,2.530 0.203,0.191 10 *b 1.74,2.46 1.944,2.651 0.203,0.191 10 *b 0.405,1.987 0.51,1.987 0.51,1.987 0.797,2.456 false 0.35,2.426 0.465,2.426 0.465,2.426 0.781,2.709 false 1.991,2.133 2.078,2.133 2.078,2.133 2.475,2.448 false 1.971,2.545 2.091,2.545 2.091,2.545 2.477,2.723 false
*a Fuse Shackle
*b Shackle (A)
*c Correct
*d Incorrect


Make sure the fuse shackle is on the chain block side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.

·
C316804C03
1.396,1.052 1,1.052 false 0.792,0.969 1,1.156 0.208,0.188 10 false *a 0.854,1.802 1.063,1.99 0.208,0.188 10 false *b 2.354,1.802 2.563,1.99 0.208,0.188 10 false *c
*a Fuse Bolt
*b Correct
*c Incorrect


Make sure the fuse bolt is not deformed.



NOTICE:
·

Prevent SST from contacting the vehicle body or windshield.

·

To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.

·

Lightly shake SST by hand to make sure it is securely installed while performing work.

·

Set the support shafts on level surfaces.




c.
C312305C04
1.063,2.146 1.365,2.146 false 1.021,2.458 1.896,2.458 false 0.708,2.521 0.792,2.521 0.792,2.521 0.854,2.771 false 0.479,1.063 0.563,1.063 0.563,1.063 0.646,1.479 false 1.406,2.073 1.604,2.281 0.198,0.208 10 false *a 1.938,2.385 2.135,2.594 0.198,0.208 10 false *d 0.552,2.438 0.75,2.646 0.198,0.208 10 false *c 0.323,0.99 0.521,1.198 0.198,0.208 10 false *b
*a Support Shaft
*b Sub Beam
*c Side Member
*d Threaded Portion


Turn the threaded portion of each support shaft to adjust its height and make the sub beams parallel to the ground.


d.

Connect the chain to the division bar with the shackle at the position shown in the illustration.

C362317C01
0.417,1.615 1.385,1.615 true 1.667,1.26 1.792,0.802 1.792,0.802 1.969,0.802 true 1.042,2.531 1.208,2.531 1.208,2.531 1.458,1.677 true 1.646,3.854 2.271,3.854 true 1.125,5.083 1.354,5.083 1.354,5.083 1.531,4.615 true 0.844,3.271 1.063,3.271 1.063,3.271 1.135,3.49 true 0.26,1.552 0.469,1.719 0.208,0.167 10 true *1 0.969,5.021 1.281,5.177 0.313,0.156 10 false *2 2,0.74 2.313,0.896 0.313,0.156 10 false *a 0.885,2.458 1.198,2.615 0.313,0.156 10 false *c 0.688,3.198 1,3.354 0.313,0.156 10 false *a 2.292,3.781 2.5,3.948 0.208,0.167 10 true *b
*1 No. 1 Engine Hanger *2 No. 2 Engine Hanger
*a Division Bar *b Shackle (A)
*c Shackle (B) - -



e.

Connect the division bar and No. 1 engine hanger with the shackle (B).


f.

Connect the 2nd link of the chain to the No. 2 engine hanger.


g.

Make sure the distance between the chain block assembly and suspension ring is 20 mm (0.787 in.) or more.

C316207C01
1.573,1.427 1.5,1.542 1.5,1.542 1.333,1.542 false 1.833,1.26 1.906,1.375 1.906,1.375 2.073,1.375 false 2.104,1.302 2.323,1.51 0.219,0.208 10 false *a 1.125,1.188 1.344,1.396 0.219,0.208 10 false *c 1.177,1.469 1.396,1.677 0.219,0.208 10 false *b
*a Chain Block Assembly *b Suspension Ring
*c 20 mm (0.787 in.) or more - -



h.

Adjust the position of the chain block assembly so that the chain is perpendicular to the main beam and sub beams as shown in the illustration.

C316208C01
3.979,0.729 4.063,0.427 4.063,0.427 4.156,0.427 false 1.677,2.094 1.073,2.094 true 6.104,2.115 5.5,2.115 true 3.25,1.146 2.99,1.146 false 2.823,1.063 3.031,1.271 0.208,0.208 10 false *a 3.365,0.333 3.573,0.542 0.208,0.208 10 false *h 4.198,0.354 4.406,0.563 0.208,0.208 10 false *b 1.615,0.281 1.823,0.49 0.208,0.208 10 true *d 5.365,0.292 5.573,0.5 0.208,0.208 10 true *e 1.5,1.406 1.708,1.615 0.208,0.208 10 false *i 5.604,1.385 5.813,1.594 0.208,0.208 10 false *i 0.917,2.021 1.125,2.229 0.208,0.208 10 false *c 6.125,2.031 6.333,2.24 0.208,0.208 10 false *c 1.281,3.438 1.49,3.646 0.208,0.208 10 false *f 4.646,3.385 4.854,3.594 0.208,0.208 10 false *g
*a Chain Block Assembly *b Main Beam
*c Sub Beam *d Dimension (A)
*e Dimension (B) *f Correct
*g Incorrect *h Right to Left Adjustment
*i Front to Rear Adjustment - -


CAUTION:

To prevent the engine assembly with automatic transaxle assembly from falling, make sure that the dimension (A) and dimension (B) are equal.



i.

Tighten the 6 wing bolts and 2 bolts.

C316209

Torque:
for Bolt : 30 N*m (306 kgf*cm, 22 ft.*lbf)


j.
C316210C01
1.369,0.782 1.608,0.993 0.239,0.211 10 *a
*a Approximately 50 mm (1.97 in.)


Move the chain block assembly approximately 50 mm (1.97 in.) as shown in the illustration.


k.
C316211C01
2.672,3.238 2.881,3.436 0.209,0.198 10 *a
*a Turn


Tighten the chain block assembly until it cannot be moved any further by hand.

CAUTION:
C316805C06
1.208,0.958 1.479,0.958 false 3.031,0.958 3.188,0.958 false 0.49,2.333 0.49,2.583 false 2.313,2.479 2.313,2.729 false 0.365,1.365 0.125,1.604 0.125,1.604 0.125,1.844 true 2.188,1.448 1.948,1.688 1.948,1.688 1.948,1.927 true 3.219,0.875 3.406,1.083 0.188,0.208 10 false *a 1.521,0.875 1.708,1.083 0.188,0.208 10 false *a 0.063,1.854 0.25,2.063 0.188,0.208 10 false *c 0.417,2.604 0.604,2.813 0.188,0.208 10 false *b 1.885,1.938 2.073,2.146 0.188,0.208 10 false *c 2.24,2.75 2.427,2.958 0.188,0.208 10 false *b 0.625,0.448 0.813,0.656 0.188,0.208 10 false *d 2.448,0.458 2.635,0.667 0.188,0.208 10 false *e
*a Chain Block Assembly
*b Suspension Ring
*c Roller
*d Incorrect
*e Correct


If the suspension ring contacts the roller of the chain block assembly, the chain block assembly may be damaged. Do not tighten the chain block assembly excessively.


NOTICE:
·

When suspending the engine assembly with automatic transaxle assembly, do not tighten the chain block assembly more than 50 N*m (510 kgf*cm, 37 ft.*lbf).

·

Do not shake the engine assembly with automatic transaxle assembly excessively while it is being suspended.




Hide 39.INSTALL BELT

a.
C312140

Remove the bolt and nut.


b.
C312141

Loosen the bolt and disconnect the windshield washer jar assembly from the vehicle body.

NOTICE:

Do not remove the bolt.



c.

Install SST to the vehicle body as shown in the illustration.

C313247N01
3.781,4.104 6.292,4.104 true 0.906,4.115 3.177,4.115 true 0.625,4.042 1.083,4.24 0.458,0.198 10 false SST 6.323,4.031 6.781,4.229 0.458,0.198 10 false SST

SST
09727-00110  


d.

Using the SST ratchet buckle, tighten the SST belt until there is no slack.

C313252C01
0.906,2.208 3.344,2.208 true 3.615,2.208 6.052,2.208 true 4.51,1.063 4.75,1.448 4.75,1.448 5.198,1.448 true 2.51,1.104 2.292,1.49 2.292,1.49 1.917,1.49 true 1.771,1.417 2.083,1.573 0.313,0.156 10 false *a 5.219,1.365 5.531,1.521 0.313,0.156 10 false *a 6.094,2.135 6.552,2.333 0.458,0.198 10 false SST 0.615,2.135 1.073,2.333 0.458,0.198 10 false SST
*a Ratchet Buckle - -



Hide 51100G 40.REMOVE FRONT FRAME ASSEMBLY

a.
C319461C01
1.458,0.667 1.177,0.667 false 1,0.583 1.229,0.719 0.229,0.135 10 false *a
*a Chain Block Assembly


Wind the chain with the chain block assembly to lift the engine assembly with automatic transaxle assembly.

NOTICE:
·

When suspending the engine assembly with automatic transaxle assembly, do not tighten the chain block assembly more than 50 N*m (510 kgf*cm, 37 ft.*lbf).

·

Lift the engine assembly with automatic transaxle assembly until the engine assembly is slightly raised off the front frame assembly.

·

Do not lift the engine assembly with automatic transaxle assembly excessively.




b.
C313394C01
0.313,1.063 0.313,0.75 true 1.354,1.021 1.354,0.563 true 2.417,0.979 2.417,0.521 true 2.417,0.719 2.667,0.719 2.667,0.719 2.667,0.552 true 1.344,0.708 0.885,0.708 0.885,0.708 0.885,0.573 true 0.25,1.073 0.563,1.229 0.313,0.156 10 false *a 1.302,1.042 1.615,1.198 0.313,0.156 10 false *b 2.365,1 2.677,1.156 0.313,0.156 10 false *b
*a Engine Lifter
*b Attachment
V100145

Attachment Placement Location


Support the front frame assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

CAUTION:
·

The front frame assembly is a heavy component. Make sure that it is supported securely.

·

Make sure to secure the front frame assembly to prevent it from dropping.



NOTICE:

Use the attachments to keep the front frame assembly level.



c.
A331865

Remove the 4 bolts, 2 nuts and frame side rail plates RH and LH.


d.

Remove the 4 bolts, 2 nuts and front suspension member rear braces RH and LH.


e.

Slowly lower the front frame assembly.

NOTICE:

When lowering the front frame assembly, be careful not to damage the vehicle body or other components installed to the vehicle.



Hide 48829A 41.REMOVE FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 42.REMOVE FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 43.REMOVE FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY

a.

Remove the front stabilizer bar with 2 front stabilizer link assemblies from the front frame assembly.


Hide 44.REMOVE STEERING LINK ASSEMBLY

Hide 48069 45.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C167143

Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front frame assembly.

NOTICE:

When removing the bolt, keep the nut from rotating.



b.

Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly LH.


Hide 48068 46.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51227B 47.REMOVE FRONT SUSPENSION MEMBER DYNAMIC DAMPER

a.
C221242

Remove the 2 bolts and front suspension member dynamic damper from the front frame assembly.


Hide 52213A 48.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER

a.

Remove the 2 front suspension member body mounting front stoppers from the front frame assembly.


Hide 52216B 49.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER

a.

Remove the 2 front suspension member body mounting rear stoppers from the front frame assembly.


Hide 52211J 50.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION

a.
C169231C05
1.188,1.01 1.365,1.01 1.365,1.01 1.49,1.427 false 1.927,0.823 2.323,0.823 false 2.74,2.188 2.292,2.188 false 2.573,2.875 2.635,2.875 2.635,2.875 2.635,2.198 false 1.01,0.938 1.271,1.135 0.26,0.198 10 false *1 2.385,0.729 2.708,0.875 0.323,0.146 10 false SST 2.771,2.104 3.094,2.25 0.323,0.146 10 false SST
*1 Front Suspension Member Body Mounting Front Cushion


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)


b.
C265514C03
0.698,2.99 1,2.99 false 2.823,0.719 2.823,0.469 false 2.594,2.917 2.896,2.917 false 0.417,2.917 0.875,3.115 0.458,0.198 10 false SST 2.74,0.708 2.938,0.917 0.198,0.208 10 false *a 2.927,2.844 3.125,3.052 0.198,0.208 10 false *b
*a Turn
*b Hold


Using SST, remove the front suspension member body mounting front cushion from the front frame assembly.

NOTICE:
·

Make sure that the claws of SST are securely hung onto the mounting cushion.

·

Tighten SST slowly and evenly.

·

Be careful as the mounting cushion may fly out.

·

The mounting cushion cannot be reused.




Hide 52217E 51.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH

a.
C169231C06
1.188,1.01 1.365,1.01 1.365,1.01 1.49,1.427 false 1.927,0.823 2.323,0.823 false 2.74,2.188 2.292,2.188 false 2.563,2.875 2.625,2.875 2.625,2.875 2.625,2.198 false 1.01,0.938 1.208,1.125 0.198,0.188 10 false *1 2.385,0.729 2.708,0.875 0.323,0.146 10 false SST 2.771,2.104 3.094,2.25 0.323,0.146 10 false SST
*1 Front Suspension Member Body Mounting Rear Cushion LH


Install SST as shown in the illustration.

SST
09830-10010  (09830-01010, 09830-01040, 09830-01050)
09950-40011  (09951-04020, 09952-04010, 09954-04010, 09955-04011, 09958-04011)


b.
C265515C03
0.677,3.031 0.99,3.031 false 2.708,0.781 2.708,0.427 false 2.677,2.917 2.99,2.917 false 0.396,2.969 0.854,3.167 0.458,0.198 10 false SST 2.625,0.781 2.938,0.938 0.313,0.156 10 false *a 3.01,2.854 3.323,3.01 0.313,0.156 10 false *b
*a Turn
*b Hold


Using SST, remove the front suspension member body mounting rear cushion LH from the front frame assembly.

NOTICE:
·

Make sure that the claws of SST are securely hung onto the mounting cushion.

·

Tighten SST slowly and evenly.

·

Be careful as the mounting cushion may fly out.

·

The mounting cushion cannot be reused.




Hide 52215 52.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH

HINT:

Perform the same procedure as for the LH side.


Hide 53.REMOVE HOLE PLUG

a.

Remove 5 hole plugs from the front frame assembly.