Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2015.04
RM19V0EQ _51 Engine / Hybrid System _014574 2AR-FE ENGINE MECHANICAL _0073931 ENGINE ASSEMBLY A

2AR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

CAUTION:

The engine assembly with transmission is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

When the manual transaxle is removed, be sure to use a new clutch release with bearing cylinder and new installation bolts. Removal of the manual transaxle allows the compressed clutch release with bearing cylinder to return to its original position, and dust from the moving section could damage the seal of the clutch release with bearing cylinder, possibly causing clutch fluid leaks.



Hide 2.RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3. DISCHARGE FUEL SYSTEM PRESSURE

Hide 4. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 5.SECURE STEERING WHEEL

Hide 6.REMOVE FRONT WHEELS

Hide 7.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 53852K 8.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH (for RHD)

Hide 51442C 9.REMOVE ENGINE UNDER COVER LH

Hide 53851Z 10.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)

Hide 51441C 11.REMOVE ENGINE UNDER COVER RH

Hide 53737B 12.REMOVE FRONT FENDER APRON SEAL LH

Hide 53736 13.REMOVE FRONT FENDER APRON SEAL RH

Hide 53295E 17.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 12601B 18.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

a.
A255403

Lift the rear of the engine cover to detach the cover from the 2 pins, and then lift the front of the engine cover to detach the cover from the pin and remove the engine cover.

NOTICE:

Attempting to disengage both front and rear clips at the same time may cause the No. 1 engine cover sub-assembly to break.



Hide 17750A 19.REMOVE INLET AIR CLEANER ASSEMBLY

a.
A255404

Remove the 2 bolts and inlet air cleaner assembly.


Hide 20.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 17801 21.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 22.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A305723

Disconnect the wire harness clamp.


b.

Remove the 2 bolts and air cleaner case sub-assembly.


Hide 23.REMOVE BATTERY

a.
A255406

Loosen the nut, and separate the positive (+) battery terminal.


b.

Loosen the nut, and remove the bolt and battery clamp.


c.

Remove the battery and battery tray.


Hide 16571C 24.DISCONNECT NO. 1 RADIATOR HOSE

a.
A268547

Remove the hose clamp to separate the air fuel ratio sensor wire from the No. 1 radiator hose.


b.

Disconnect the No. 1 radiator hose.


Hide 16572D 25.DISCONNECT NO. 2 RADIATOR HOSE

a.
A255407

Disconnect the No. 2 radiator hose.


Hide 87245 26.DISCONNECT INLET HEATER WATER HOSE

a.
A203579

Disconnect the inlet heater water hose.


Hide 87246 27.DISCONNECT OUTLET HEATER WATER HOSE (for LHD)

a.
A207312

Disconnect the outlet heater water hose.


Hide 87246 28.DISCONNECT OUTLET HEATER WATER HOSE (for RHD)

a.
A255408

Disconnect the 3 outlet heater water hoses.


Hide 32942 29.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

a.
A257988

Disconnect the outlet No. 1 oil cooler hose from the automatic transaxle assembly.


Hide 32941 30.DISCONNECT INLET NO. 1 OIL COOLER HOSE

a.
A257990

Disconnect the inlet No. 1 oil cooler hose from the automatic transaxle assembly.


Hide 28100 31.REMOVE STARTER ASSEMBLY

Hide 82121 32.DISCONNECT ENGINE WIRE

a.

Remove the No. 1 relay block cover.


b.
A255436

Remove the 2 nuts and disconnect the wire clamp.


c.

Using a screwdriver, unlock the claw and separate the engine wire from the engine room relay block.


d.
A255438

Disconnect the 4 connectors.


e.

Using a screwdriver, unlock the claw and separate the engine wire from the engine room relay block.


f.

Pull up the lever to disconnect the ECM connector.


g.
A255462

Disconnect the 2 wire clamps.


Hide 17771A 33.REMOVE NO. 1 AIR CLEANER BRACKET

a.
A255409

Disconnect the 2 wire clamps.


b.

Remove the bolt and No. 1 air cleaner bracket.


Hide 33820B 34.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C239655

Disconnect the wire harness clamp.


b.
C239668

Remove the nut and clip, and disconnect the transmission control cable assembly.


Hide 12327A 35.REMOVE NO. 2 ENGINE MOUNTING STAY RH

a.
A255411

Remove the 2 bolts and No. 2 engine mounting stay RH.


Hide 82284 36.SEPARATE EARTH WIRE

a.
A255410

Remove the bolt and separate the earth wire from the engine moving control rod bracket.


Hide 12309 37.REMOVE ENGINE MOVING CONTROL ROD SUB-ASSEMBLY

a.
A255452

Remove the 4 bolts and engine moving control rod sub-assembly.


Hide 44774 38.DISCONNECT UNION TO CONNECTOR TUBE HOSE (for LHD)

a.
A255453

Disconnect the union to connector tube hose.


Hide 44773F 39.DISCONNECT UNION TO CHECK VALVE HOSE (for RHD)

a.
A268064

Disconnect the union to check valve hose.


Hide 88711 40.DISCONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

Hide 88704 41.DISCONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 23901 42.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A203577

Release the claw and remove the No. 1 fuel pipe clamp.


b.

Pinch the fuel tube connector and then pull out the fuel main tube.

NOTICE:
·

Check for dirt and foreign objects on the pipe and around the connector. Clean if necessary and then disconnect the connector.

·

Disconnect the connector by hand.

·

Do not bend, fold or rotate the nylon tube.

·

If the pipe and connector are stuck together, push and pull the connector until it becomes free.

·

Put the pipe and connector ends in vinyl bags to prevent damage and contamination.




Hide 17410 43.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 43502H 44.REMOVE FRONT AXLE SHAFT NUT LH

Hide 43501H 45.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 46.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 47.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 89543 48.SEPARATE FRONT SPEED SENSOR LH

Hide 89542 49.SEPARATE FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 45470 50.SEPARATE TIE ROD ASSEMBLY LH

Hide 45460 51.SEPARATE TIE ROD ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48069 52.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 53.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 43502C 54.SEPARATE FRONT AXLE ASSEMBLY LH

Hide 43501C 55.SEPARATE FRONT AXLE ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45220 56.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 11361J 57.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
A196625

Remove the flywheel housing under cover.


Hide 32101A 58.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
A196626

Turn the crankshaft to gain access to the removal locations of the 6 torque converter assembly setting bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.


Hide 59.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.
A255461C08
0.708,1.5 0.708,1.49 false
V100145

Attachment Installation Position


Set an engine lifter.

NOTICE:
·

Install a height adjustment attachment and plate lift attachment onto the engine assembly with transaxle.

·

Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.

·

To prevent the oil pan from deforming, do not place any attachments onto the oil pan of the engine assembly with transaxle.

·

Servicing an engine assembly while it is hanging is dangerous. This can be done only when installing/removing the engine assembly to/from an engine stand.

·

Do not perform any procedure while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed or removed from an engine stand.




b.
A255454

Remove the 4 bolts, 2 nuts, and frame side rail plate RH and LH.


c.

Remove the 4 bolts, 2 nuts, and front suspension member brace rear RH and LH.


d.

Operate the engine lifter and remove the engine assembly from the vehicle.

NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While lowering the engine from the vehicle, do not allow it to contact the vehicle.





Hide 82121 60.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine with transaxle.


Hide 88310 62.REMOVE COMPRESSOR ASSEMBLY WITH PULLEY

Hide 27020 63.REMOVE GENERATOR ASSEMBLY

Hide 43420 64.REMOVE FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43420G 65.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING LH

Hide 43410 66.REMOVE FRONT DRIVE SHAFT ASSEMBLY RH

Hide 51100G 67.REMOVE FRONT FRAME ASSEMBLY

a.

Loosen the bolt and 2 nuts.

A265024C01
0.344,0.125 1.292,0.365 0.948,0.24 10 false *a 2.885,0.125 3.708,0.344 0.823,0.219 10 false *b 5.115,0.125 5.938,0.344 0.823,0.219 10 false *c
*a Front Side *b LH Side
*c RH Side - -



b.

Remove the 4 hole plugs.

A256545C08
0.707,0.06 0.975,0.291 0.267,0.23 10 *a 4.112,0.06 4.379,0.291 0.267,0.23 10 *b
*a Engine Mounting Insulator RH *b Engine Mounting Insulator LH



c.

Remove the 9 nuts, and separate the front frame assembly.

A172973C07
0.208,0.063 0.74,0.5 0.531,0.438 10 false *a 2.198,0.063 2.677,0.448 0.479,0.385 10 false *b 4.646,0.063 4.979,0.292 0.333,0.229 10 false *c
*a Front Side *b RH Side
*c LH Side - -



d.

Using a height adjustable attachment and plate lift attachment, place the engine assembly on a flat level surface.

NOTICE:
·

Using a height adjustable attachment and plate lift attachment, place the engine assembly with transaxle horizontally.

·

To prevent the oil pan from deforming, do not place any attachments onto the oil pan of the engine assembly with transaxle.

·

Using an engine sling device and engine lift, secure the engine assembly before service.




Hide 12361A 68.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
A265026

Remove the bolt and front engine mounting insulator.


Hide 12372A 69.REMOVE ENGINE MOUNTING INSULATOR LH

a.
A196630

Remove the nut and engine mounting insulator LH.


Hide 12362A 70.REMOVE ENGINE MOUNTING INSULATOR RH

a.
A196631

Remove the nut and engine mounting insulator RH.


Hide 43457 71.REMOVE DRIVE SHAFT BEARING BRACKET

a.
A196633

Remove the 3 bolts and drive shaft bearing bracket.


Hide 12315A 72.REMOVE ENGINE MOUNTING BRACKET RH

a.
A196634

Remove the 3 bolts and engine mounting bracket RH.


Hide 32101 74.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

Hide 75.INSTALL ENGINE STAND

a.

Install the engine onto an engine stand with the bolts.