Home › Engine / Hybrid System › 2GR-FE ENGINE MECHANICAL › ENGINE UNIT › from 2013.07
RM2030EQ _51 Engine / Hybrid System _014635 2GR-FE ENGINE MECHANICAL _0074417 ENGINE UNIT A

2GR-FE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 11381A 1.INSTALL ENGINE REAR OIL SEAL

a.

Place the engine rear oil seal retainer on wooden blocks.


b.
A120675C07
0.906,1.208 0.552,0.844 0.552,0.844 1.125,0.844 false 0.25,0.76 0.708,0.958 0.458,0.198 10 false SST

Using SST, tap in a new engine rear oil seal until its surface is flush with the engine rear oil seal retainer edge.

SST
09223-15030  
09950-70010  (09951-07100)

NOTICE:
·

Keep the lip free of foreign matter.

·

Do not tap in the engine rear oil seal at an angle.




c.

Apply MP grease to the engine rear oil seal lip.


Hide 11381 2.INSTALL ENGINE REAR OIL SEAL RETAINER

a.
A187879C03
2.433,0.058 2.603,0.219 0.17,0.161 10 *a 2.424,0.151 2.154,0.473 false
*a Seal Packing Diameter
(2.0 to 3.0 mm (0.0787 to 0.118 in.))


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal Packing Diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the engine rear oil seal retainer within 3 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




b.
A129686N04
0.135,0.146 0.25,0.313 0.115,0.167 10 A 2.542,0.865 2.844,1.177 0.302,0.313 10 A

Install the engine rear oil seal retainer with the 6 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Be sure to apply adhesive to the bolts in the places indicated by (A) before installing them.


Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



Hide 16322 3.INSTALL WATER INLET PIPE

a.
A268438

Install the water inlet pipe with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 1 water by-pass hose to the water inlet pipe and slide the clip to secure it.


Hide 11101 5.INSTALL CYLINDER HEAD SUB-ASSEMBLY RH

Hide 11102 7.INSTALL CYLINDER HEAD SUB-ASSEMBLY LH

Hide 13750 9.INSTALL VALVE LASH ADJUSTER ASSEMBLY

Hide 13801 10.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13.INSTALL CAMSHAFT BEARING CAP (for Bank 2)

Hide 11104A 14.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

Hide 17.INSTALL CAMSHAFT BEARING CAP (for Bank 1)

Hide 11103C 18.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

Hide 13560A 19.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 20.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)

Hide 13550 21.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 22.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)

Hide 13561 23.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.
A120649

Install the No. 1 chain vibration damper with the 2 bolts.

Torque:
22.5 N*m (229 kgf*cm, 17 ft.*lbf)


Hide 13562 24.INSTALL NO. 2 CHAIN VIBRATION DAMPER

a.

Install the 2 No. 2 chain vibration dampers.


Hide 13521 25.INSTALL CRANKSHAFT TIMING SPROCKET

a.
A109720

Install the 2 keys and crankshaft timing sprocket as shown in the illustration.


Hide 13530 26.INSTALL IDLE SPROCKET ASSEMBLY

a.
A132222C03
0.708,0.958 0.479,0.271 0.479,0.271 0.333,0.271 false 0.146,0.208 0.313,0.385 0.167,0.177 10 *1
*1 Knock Pin


Apply a light coat of engine oil to the rotating surface of the No. 1 idle gear shaft.


b.

Temporarily install the No. 1 idle gear shaft and idle sprocket assembly with the No. 2 idle gear shaft while aligning the knock pin of the No. 1 idle gear shaft with the knock pin groove of the cylinder block sub-assembly.

NOTICE:

Be careful of the No. 1 idle gear shaft installation position.


HINT:

Check that no foreign matter is on the No. 1 idle gear shaft or No. 2 idle gear shaft.



c.

Using a 10 mm hexagon wrench, tighten the No. 2 idle gear shaft.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)

HINT:

After installing the idle sprocket assembly, check that the idle sprocket assembly turns smoothly.



Hide 13506 27.INSTALL CHAIN SUB-ASSEMBLY

a.
A132223C03
0.74,0.979 1.771,1.896 1.771,1.896 2.563,1.031 false 0.625,0.875 0.438,1.479 false 2.719,0.927 2.938,1.479 false 0.375,1.49 0.656,1.667 0.281,0.177 10 false *a 1.688,1.948 1.854,2.104 0.167,0.156 10 false *b 2.875,1.49 3.042,1.667 0.167,0.177 10 false *a
*a Mark Plate
*b Timing Mark


Align the mark plates and timing marks as shown in the illustration and install the chain sub-assembly.

HINT:

The camshaft mark plates are orange.



b.
A134890

Do not pass the chain sub-assembly over the crankshaft, just temporarily place it on the crankshaft.


c.

Turn the camshaft timing gear assembly on bank 1 counterclockwise to tighten the chain sub-assembly between the banks.

A293120C03
6.448,2.021 5.854,1.781 false 5.042,1.49 5.083,2.01 5.083,2.01 5.677,1.719 false 4.052,1.729 5.073,1.365 false 6.51,1.938 6.792,2.156 0.281,0.219 10 false *a 5,2.052 5.281,2.271 0.281,0.219 10 false *e 3.875,1.656 4.156,1.875 0.281,0.219 10 false *d 1.031,0.177 1.313,0.396 0.281,0.219 10 false *b 3.76,0.188 4.042,0.406 0.281,0.219 10 false *c
*a Mark Plate *b Turn
*c When the idle sprocket assembly is reused *d Mark
*e Align - -


NOTICE:

When the idle sprocket assembly is reused, align the mark plate with the mark where the plate had been in order to tighten the chain sub-assembly between the banks.



d.
A132224C04
2.99,1.271 2.156,0.229 false 2.781,1.271 2.448,2.031 2.448,2.031 2.604,1.396 false 2.292,1.99 2.469,2.135 0.177,0.146 10 false *b 2,0.052 2.208,0.208 0.208,0.156 10 false *a
*a Mark Plate
*b Timing Mark


Align the mark plate and timing marks as shown in the illustration and install the chain sub-assembly onto the crankshaft timing sprocket.

HINT:

The crankshaft mark plate is yellow.



e.

Temporarily tighten the pulley set bolt.


f.
A205165C09
0.635,0.615 0.385,1.521 0.385,1.521 1.594,0.938 false 0.458,0.198 0.708,0.198 false 1.906,1.917 2.156,2.031 false 2.219,1.969 2.396,2.135 0.177,0.167 10 false *a 0.75,0.135 0.927,0.302 0.177,0.167 10 false *b 0.24,1.542 0.521,1.74 0.281,0.198 10 false *c
*a Sensor Plate
*b Center Line
*c Timing Mark


Turn the crankshaft clockwise to align the timing mark on the crank angle sensor plate with the RH block bore center line (TDC/compression).


Hide 13559 28.INSTALL CHAIN TENSIONER SLIPPER

a.

Install the chain tensioner slipper.


Hide 13540 29.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A132225C03
0.938,1.344 0.625,1.646 0.625,1.646 0.625,1.792 false 2.583,1.198 2.792,0.542 2.792,0.542 2.969,0.542 false 1.635,1.469 1.406,0.542 1.406,0.542 1.229,0.542 false 2.896,1.365 2.896,1.75 false 0.542,1.792 0.698,1.958 0.156,0.167 10 false *a 2.802,1.74 2.979,1.927 0.177,0.188 10 false *b 1.073,0.448 1.25,0.635 0.177,0.188 10 false *b 2.979,0.438 3.208,0.635 0.229,0.198 10 false *a
*a Stopper Plate
*b Plunger


Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.


b.

Move the stopper plate downward to set the lock, and insert a hexagon wrench into the hole of the stopper plate.


c.
A095165

Install the No. 1 chain tensioner assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Remove the hexagon wrench from the No. 1 chain tensioner assembly.


Hide 30.INSPECT VALVE TIMING

a.

Check the camshaft timing marks.

NOTICE:
·

Check each timing mark from a viewpoint directly in line with the center of the camshaft and the timing mark on each camshaft timing gear assembly and each camshaft timing exhaust gear assembly.

·

If the timing marks are checked from any other viewpoint, the valve timing may appear misaligned.




b.

Check that each camshaft timing mark is positioned as shown in the illustration.

A182779C04
1.427,0.531 1.177,1.125 1.177,1.125 1.438,0.875 true 4.583,0.635 4.354,1.208 4.354,1.208 4.604,1.01 true 1.927,2.542 1.615,3.094 1.615,3.094 1.906,2.917 true 5.833,2.396 6.417,3.073 6.417,3.073 5.844,2.688 true 0.51,4.5 0.792,4.729 0.281,0.229 10 false *b 1.021,1.104 1.219,1.292 0.198,0.188 10 false *a 1.177,4.031 1.458,4.271 0.281,0.24 10 false *b 3.646,3.906 3.875,4.146 0.229,0.24 10 false *b 4.365,4.271 4.688,4.563 0.323,0.292 10 false *b 4.219,1.188 4.417,1.375 0.198,0.188 10 false *a 1.479,3.063 1.677,3.25 0.198,0.188 10 false *a 6.448,3.042 6.677,3.271 0.229,0.229 10 false *a
*a Timing Mark *b Viewpoint


HINT:
A293131N02
1.75,0.74 2.385,0.698 false 1.708,0.917 2.385,0.958 false 1.729,1.281 2.406,1.292 false 1.719,1.594 2.406,1.594 false 2.448,0.615 2.625,0.844 0.177,0.229 10 A 2.448,0.885 2.635,1.125 0.188,0.24 10 B 2.469,1.219 2.667,1.469 0.198,0.25 10 C 2.479,1.531 2.677,1.76 0.198,0.229 10 D

For the camshaft or No. 3 camshaft:

Be sure to check the mark (A) at the point when the marks (B), (C), and (D) are positioned in line. If the marks are checked from any other viewpoint, they cannot be checked correctly.



c.

If the valve timing is misaligned, reinstall the chain sub-assembly.


d.

Remove the pulley set bolt.


Hide 11301C 31.INSTALL TIMING CHAIN CASE OIL SEAL

Hide 16100 32.INSTALL ENGINE WATER PUMP ASSEMBLY

a.
A192425N02
0.963,0.439 1.082,0.589 0.119,0.15 10 A 1.092,1.688 1.21,1.838 0.119,0.15 10 A

Install a new water pump gasket and the engine water pump assembly with the 8 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)

NOTICE:

Be sure to replace the bolts (A) with new ones or reuse them after applying adhesive.


Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



Hide 11302 33.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Apply seal packing in a continuous line to the engine unit as shown in the following illustration.

A306195C03
3.792,1.76 4.208,1.344 false 4.948,0.573 5.104,0.188 5.104,0.188 5.302,0.188 false 6.594,1.542 6.448,1.125 false 5.979,0.906 5.76,1.073 5.76,1.073 5.823,0.833 true 5.26,1.792 5.385,1.646 5.385,1.646 5.177,1.51 true 0.396,1.667 0.917,2.115 0.521,0.448 10 false A 1.344,1.385 1.865,1.833 0.521,0.448 10 false A 2.063,1.313 2.583,1.76 0.521,0.448 10 false A 2.927,1.469 3.448,1.917 0.521,0.448 10 false A 3.698,1.813 3.854,2.01 0.156,0.198 10 false B 5.417,1.552 5.573,1.75 0.156,0.198 10 false C 5.729,1.104 5.885,1.302 0.156,0.198 10 false C 6.573,1.604 6.729,1.802 0.156,0.198 10 false B 5.396,0.083 5.552,0.281 0.156,0.198 10 false B 3.427,3.146 3.948,3.594 0.521,0.448 10 false A 3.823,3.823 4.135,4.021 0.313,0.198 10 false *a
*a Seal Diameter: 3.0 mm or more
V100135

Seal Packing


Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal Packing Diameter:

3.0 mm (0.118 in.)


NOTICE:
·

Be sure to clean and degrease the contact surfaces, especially the surfaces indicated by (B) in the illustration.

·

If there is oil on the contact surfaces, wipe them with an oil-free cloth before applying seal packing.

·

Install the timing chain cover sub-assembly within 3 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




b.

Apply seal packing in a continuous line to the timing chain cover sub-assembly as shown in the following illustration.

A187885C05
1.688,1.802 1.229,2.906 1.229,2.906 2.49,1.417 true 4.99,0.417 3.094,1.417 true 6.042,4.781 5.844,3.885 5.844,3.885 5.573,3.885 false 2.813,4.167 3.156,4.167 3.156,4.167 3.302,4.792 false 0.615,2.948 1.771,3.188 1.156,0.24 10 false 20 mm (0.787 in.) 5.063,0.333 6.188,0.688 1.125,0.354 10 false 20 mm (0.787 in.) 6.313,1.448 6.51,1.677 0.198,0.229 10 false *a 6.344,2.115 6.542,2.344 0.198,0.229 10 false *b 6.344,2.792 6.542,3.021 0.198,0.229 10 false *c 6.354,3.438 6.552,3.667 0.198,0.229 10 false *d 1.323,4.719 2.521,4.917 1.198,0.198 10 false 5.0 mm (0.197 in.) 1.896,4.104 3.073,4.469 1.177,0.365 10 false 3.0 to 4.0 mm 4.219,4.698 5.438,4.885 1.219,0.188 10 false 2.0 to 3.0 mm 4.5,3.813 5.813,4.313 1.313,0.5 10 false 1.0 to 2.0 mm 1.896,4.26 3.135,4.458 1.24,0.198 10 false (0.118 to 0.157 in.) 4.5,3.979 5.99,4.26 1.49,0.281 10 false (0.0394 to 0.0787 in.) 4.208,4.865 5.5,5.125 1.292,0.26 10 false (0.0787 to 0.118 in.)
*a Dashed line area
(Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent)
*b Continuous line area
(Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent)
*c Alternate long and short dashed line area
(Seal packing: Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent)
*d Diagonal line area
(Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent)
V100135

Be sure to apply seal packing - -


Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


NOTICE:
·

If there is oil on the contact surfaces, wipe them with an oil-free cloth before applying seal packing.

·

Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.



Seal Packing Application Chart
Area Seal Packing Diameter Application Position from Inside Seal Line
Continuous Line Area 4.5 mm or more (0.177 in.) 1.0 to 2.0 mm (0.0394 to 0.0787 in.)
Alternate Long and Short Dashed Line Area 3.5 mm or more (0.138 in.) 2.0 to 3.0 mm (0.0787 to 0.118 in.)
Dashed Line Area 3.5 mm or more (0.138 in.) 3.0 to 4.0 mm (0.118 to 0.157 in.)
Diagonal Line Area 6.0 mm or more (0.236 in.) 5.0 mm (0.197 in.)


c.
A128017

Install a new gasket.


d.
A132229C05
2.417,1.635 2.958,1.708 false 0.75,1.625 1.281,1.688 false 1.333,1.604 1.5,1.76 0.167,0.156 10 false *a 2.99,1.635 3.146,1.792 0.156,0.156 10 false *1
*1 Crankshaft
*a Drive Rotor Spline


Align the drive rotor spline of the oil pump and the crankshaft as shown in the illustration. Install the drive rotor spline and timing chain cover sub-assembly to the crankshaft.


e.

Type X:

i.
A187948C03
1.802,0.708 1.917,0.865 0.115,0.156 10 false A 1.052,1.813 1.177,1.969 0.125,0.156 10 true B 0.083,1.677 0.219,1.833 0.135,0.156 10 false C 2.438,2.635 2.635,2.792 0.198,0.156 10 false *1 0.677,2.667 0.875,2.823 0.198,0.156 10 false *1 1.313,1.531 1.427,1.688 0.115,0.156 10 false B 2.302,2.292 2.417,2.448 0.115,0.156 10 false B 3.292,1.292 3.406,1.448 0.115,0.156 10 false B 2.76,1.813 2.875,1.969 0.115,0.156 10 false B 2.771,2.052 2.885,2.208 0.115,0.156 10 false B 2.094,1.51 2.229,1.667 0.135,0.156 10 true B 1.854,1.99 1.979,2.146 0.125,0.156 10 true B 1.292,2.302 1.438,2.49 0.146,0.188 10 true B 0.76,2.302 0.896,2.458 0.135,0.156 10 true B 0.531,1.969 0.646,2.125 0.115,0.156 10 false B 1.26,1.875 1.385,2.073 0.125,0.198 10 true B 2.896,1.667 3.031,1.823 0.135,0.156 10 false C 1.969,0.5 2.104,0.656 0.135,0.156 10 false C 1.646,0.927 1.781,1.083 0.135,0.156 10 false C 1.25,1.354 1.385,1.51 0.135,0.156 10 false C 1.208,1.198 1.344,1.354 0.135,0.156 10 false C 1.094,0.99 1.229,1.146 0.135,0.156 10 false C 0.74,2.479 0.875,2.635 0.135,0.156 10 false C 0.396,1.896 0.531,2.052 0.135,0.156 10 false C 0.292,1.76 0.427,1.917 0.135,0.156 10 false C
*1 Nut


Temporarily tighten the timing chain cover sub-assembly with the 23 bolts and 2 nuts.

Bolt Length
Item Length
Bolt A 40 mm (1.57 in.)
Bolt B 55 mm (2.17 in.)
Bolt C 25 mm (0.984 in.)

NOTICE:

Make sure that there is no oil on the threads of the bolts (B) and (C).




f.

Type Y:

i.
A187948C03
1.802,0.708 1.917,0.865 0.115,0.156 10 false A 1.052,1.813 1.177,1.969 0.125,0.156 10 true B 0.083,1.677 0.219,1.833 0.135,0.156 10 false C 2.438,2.635 2.635,2.792 0.198,0.156 10 false *1 0.677,2.667 0.875,2.823 0.198,0.156 10 false *1 1.313,1.531 1.427,1.688 0.115,0.156 10 false B 2.302,2.292 2.417,2.448 0.115,0.156 10 false B 3.292,1.292 3.406,1.448 0.115,0.156 10 false B 2.76,1.813 2.875,1.969 0.115,0.156 10 false B 2.771,2.052 2.885,2.208 0.115,0.156 10 false B 2.094,1.51 2.229,1.667 0.135,0.156 10 true B 1.854,1.99 1.979,2.146 0.125,0.156 10 true B 1.292,2.302 1.438,2.49 0.146,0.188 10 true B 0.76,2.302 0.896,2.458 0.135,0.156 10 true B 0.531,1.969 0.646,2.125 0.115,0.156 10 false B 1.26,1.875 1.385,2.073 0.125,0.198 10 true B 2.896,1.667 3.031,1.823 0.135,0.156 10 false C 1.969,0.5 2.104,0.656 0.135,0.156 10 false C 1.646,0.927 1.781,1.083 0.135,0.156 10 false C 1.25,1.354 1.385,1.51 0.135,0.156 10 false C 1.208,1.198 1.344,1.354 0.135,0.156 10 false C 1.094,0.99 1.229,1.146 0.135,0.156 10 false C 0.74,2.479 0.875,2.635 0.135,0.156 10 false C 0.396,1.896 0.531,2.052 0.135,0.156 10 false C 0.292,1.76 0.427,1.917 0.135,0.156 10 false C
*1 Nut


Temporarily tighten the timing chain cover sub-assembly with the 23 bolts and 2 nuts.

Bolt Length
Item Length
Bolt A 40 mm (1.57 in.)
Bolt B 55 mm (2.17 in.)
Bolt C 28 mm (1.102 in.)

NOTICE:

Make sure that there is no oil on the threads of the bolts (B) and (C).




g.
A187949C05
0.198,1.646 0.198,1.438 false 0.427,1.969 0.521,1.969 0.521,1.969 0.75,1.823 false 0.781,2.729 0.979,2.729 false 0.927,0.427 1.115,0.427 1.115,0.427 1.385,0.635 false 2.354,0.469 2.188,0.469 2.188,0.469 2.063,0.646 false 3.146,1.719 3.031,1.719 3.031,1.719 2.917,1.531 false 2.875,1.917 2.75,1.917 2.75,1.917 2.469,1.771 false 2.771,2.208 2.656,2.208 2.656,2.208 2.563,2.073 false 1.385,1.563 1.469,1.563 1.469,1.563 1.552,1.688 false 1.771,0.729 1.844,0.729 1.844,0.729 1.906,0.958 false 0.271,1.865 0.448,2.052 0.177,0.188 10 false *a 1.24,1.458 1.417,1.646 0.177,0.188 10 false *b 0.635,2.625 0.813,2.802 0.177,0.177 10 false *c 0.115,1.656 0.292,1.833 0.177,0.177 10 false *d 2.927,1.823 3.104,2.01 0.177,0.188 10 false *a 2.802,2.104 2.979,2.281 0.177,0.177 10 false *c 3.198,1.635 3.375,1.813 0.177,0.177 10 false *d 2.396,0.365 2.573,0.542 0.177,0.177 10 false *d 0.771,0.323 0.948,0.5 0.177,0.177 10 false *d 1.646,0.635 1.76,0.802 0.115,0.167 10 false A
*a Area 1
*b Area 2
*c Area 3
*d Area 4


Fully tighten the bolts in this order: Area 1 and Area 2.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


h.

Fully tighten the bolts and nuts in Area 3.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

Tighten the bolts and nuts from top to bottom as shown in the illustration.



i.

Fully tighten the bolts in Area 4.

Torque:
Bolt A : 43 N*m (438 kgf*cm, 32 ft.*lbf)
Except Bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

Tighten the bolts from bottom to top as shown in the illustration.



j.

Install a new timing chain cover plate gasket and the timing chain cover plate with the 4 bolts.

Torque:
9.1 N*m (93 kgf*cm, 81 in.*lbf)


Hide 16323 34.INSTALL WATER INLET HOUSING

a.
A129675N04
1.448,0.771 1.646,0.969 0.198,0.198 10 A

Install 2 new O-rings.

HINT:

Apply a small amount of water or soapy water to the O-ring (A) shown in the illustration before installation.



b.
A137975N05
1.167,2.208 1.823,2.531 0.656,0.323 10 false 9 mm 1.167,2.833 1.813,3.146 0.646,0.313 10 false 9 mm 2.385,2.49 3.052,2.865 0.667,0.375 10 false 25 mm 1.167,2.375 2.854,2.573 1.688,0.198 10 false (0.354 in.) 1.156,2.99 2.844,3.188 1.688,0.198 10 false (0.354 in.) 2.375,2.646 3.104,2.896 0.729,0.25 10 false (0.984 in.)

Install the 2 stud bolts.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.
A307377C01
1.021,1.333 1.333,1.531 0.313,0.198 10 false *1 1.969,0.573 2.281,0.771 0.313,0.198 10 false *2 1.813,1.948 2.125,2.146 0.313,0.198 10 false *2
*1 Nut
*2 Bolt


Install the water inlet housing with the 2 bolts and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Be careful that the O-ring does not get caught between the parts.



d.

Connect the No. 1 water by-pass hose to the water inlet housing and slide the clip to secure it.


e.

Apply adhesive around the drain cock assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.

Install the drain cock assembly to the water inlet housing.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


g.

Install the drain cock plug to the drain cock assembly.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


h.

Install a new gasket to the thermostat.


i.
A134896N04
1.206,0.0 1.512,0.187 0.306,0.187 10 10° 1.718,0.0 2.024,0.187 0.306,0.187 10 10°

Align the thermostat jiggle valve with the upper stud bolt, and insert the thermostat in the water inlet housing.

HINT:

The thermostat jiggle valve may be set within 10° of either side of the prescribed position.



j.
A129673

Install the water inlet with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12315 35.INSTALL NO. 1 FRONT ENGINE MOUNTING BRACKET LH

a.
A134961C04
1.469,0.344 1.469,0.167 1.469,0.167 2.417,0.167 false 1.615,0.354 1.615,0.167 false 2.458,0.083 2.615,0.25 0.156,0.167 10 false *1 2.375,3.417 3.188,3.573 0.813,0.156 10 false 29 mm 1.198,3.156 1.948,3.333 0.75,0.177 10 false 14 mm 1.208,3.677 1.99,3.854 0.781,0.177 10 false 13 mm 1.208,3.323 2.896,3.521 1.688,0.198 10 false (0.551 in.) 1.219,3.833 1.917,4.031 0.698,0.198 10 false (0.512 in.) 2.375,3.583 2.99,3.802 0.615,0.219 10 false (1.14 in.)
*1 Stud Bolt


Using an E8 "TORX" socket wrench, install the 2 stud bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Install the No. 1 front engine mounting bracket LH with the 6 bolts.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)

NOTICE:
·

Install the water inlet and No. 1 front engine mounting bracket LH within 15 minutes of installing the timing chain cover sub-assembly.

·

Do not start the engine for at least 2 hours after installation.




Hide 12121 36.INSTALL NO. 1 OIL PAN BAFFLE PLATE

a.
A129685N05
0.885,0.271 1.104,0.49 0.219,0.219 10 A 3,1.813 3.219,2.031 0.219,0.219 10 A

Install the No. 1 oil pan baffle plate with the 7 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

Temporarily tighten the 7 bolts. Fully tighten the 2 bolts (A) shown in the illustration before tightening the other bolts.



Hide 12101 37.INSTALL OIL PAN SUB-ASSEMBLY

a.

Using an E8 "TORX" socket wrench, install the 4 stud bolts.

A374607C02
0.177,0.094 6.99,2.177 6.813,2.083 0.177,2.177 6.99,4.26 6.813,2.083 0.24,0.135 0.906,0.781 0.667,0.646 12 false *A 0.26,2.229 1.094,2.76 0.833,0.531 12 false *B 5.417,0.115 5.729,0.271 0.313,0.156 10 false *b 1.438,0.104 1.75,0.26 0.313,0.156 10 false *a 1.521,4.531 1.833,4.688 0.313,0.156 10 false *c 5.542,4.688 5.854,4.844 0.313,0.156 10 false *d 5.563,5.177 5.875,5.333 0.313,0.156 10 false *e 6.792,4.948 7.104,5.104 0.313,0.156 10 false *f 3.094,2.198 3.406,2.354 0.313,0.156 10 false *b 6.021,1.948 6.177,2.146 0.156,0.198 10 true A 0.958,1.552 1.115,1.75 0.156,0.198 10 false A 3.948,2.229 4.104,2.427 0.156,0.198 10 true A 3.75,4.031 3.906,4.229 0.156,0.198 10 true A 1.167,5.115 1.323,5.313 0.156,0.198 10 false B 0.49,5.156 0.646,5.354 0.156,0.198 10 false B
*A Type A *B Type B
*a Timing Chain Cover Sub-assembly Side *b Cylinder Block Sub-assembly Bottom Side
*c Oil Pan Sub-assembly LH Side *d 20 mm (0.787 in.)
*e 13 mm (0.512 in.) *f 35 mm (1.38 in.)


Torque:
Stud Bolt (A) : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Stud Bolt (B) : 9.0 N*m (92 kgf*cm, 80 in.*lbf)


b.
A129684

Install 2 new O-rings.


c.
A187880C02
2.694,0.105 2.88,0.291 0.186,0.186 10 *a 2.676,0.192 2.378,0.65 false
*a Seal Packing


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal Packing Diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan sub-assembly within 3 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




d.
A376238C04
0.292,0.073 0.656,0.313 0.365,0.24 12 false *A 0.292,2.406 0.656,2.677 0.365,0.271 12 false *B 2.938,0.833 3.094,1.031 0.156,0.198 10 false A 2.948,1.104 3.104,1.302 0.156,0.198 10 false A 2.948,3.167 3.104,3.365 0.156,0.198 10 false A 2.948,3.438 3.104,3.635 0.156,0.198 10 false A
*A Type A
*B Type B
V100135

Bolt
V100136

Nut


Install the oil pan sub-assembly with the 16 bolts and 2 nuts.

Torque:
Bolt (A) : 10 N*m (102 kgf*cm, 7 ft.*lbf)
Except Bolt (A) : 21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 15104 38.INSTALL OIL STRAINER SUB-ASSEMBLY

a.
A134963C06
1.458,2.49 1.906,1.969 false 1.458,2.844 1.885,3.198 false 0.938,1.427 1.094,1.427 1.094,1.427 1.365,1.219 false 0.708,1.365 0.896,1.552 0.188,0.188 10 false *1 2.375,2.5 3.063,2.688 0.688,0.188 10 false 27 mm 1.938,1.875 3.094,2.052 1.156,0.177 10 false 16 mm (0.630 in.) 1.979,3.135 3.01,3.354 1.031,0.219 10 false 9 mm (0.354 in.) 2.365,2.656 2.99,2.896 0.625,0.24 10 false (1.06 in.)
*1 Timing Chain Cover Sub-assembly


Using an E6 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
A129681C06
1.021,1.802 1.188,1.969 0.167,0.167 10 true *1 1.167,0.854 1.333,1.021 0.167,0.167 10 true *1
*1 Nut


Install a new gasket and the oil strainer sub-assembly with the bolt and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12102A 39.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.
A306211N01
1.24,2.615 2.344,2.844 1.104,0.229 10 false 9 mm (0.354 in.) 1.219,3.031 2.323,3.26 1.104,0.229 10 false 9 mm (0.354 in.) 2.552,2.813 3.333,3.135 0.781,0.323 10 false 20 mm (0.787 in.)

Using an E6 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
A187881C02
3.039,0.405 3.223,0.568 0.184,0.163 10 *a 3.01,0.521 2.666,0.697 false
*a Seal Diameter


Apply seal packing in a continuous line as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal Packing Diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 2 oil pan sub-assembly within 3 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




c.
A306210C03
0.344,1.667 0.656,1.865 0.313,0.198 10 false *1 2.458,0.531 2.771,0.729 0.313,0.198 10 false *1
*1 Nut


Install the No. 2 oil pan sub-assembly with the 16 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12101A 40.INSTALL OIL PAN DRAIN PLUG

a.
A129654

Install a new oil pan drain plug gasket and the oil pan drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 11201 41.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A187882C02
1.823,1.75 1.948,1.75 false
V100135

Seal Packing


Apply seal packing as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover sub-assembly within 3 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




b.
A129699

Install 3 new gaskets as shown in the illustration.


c.

Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.


d.
A129679C05
0.427,1.031 0.198,1.531 0.198,1.531 0.688,1.74 false 1.823,1.385 1.823,1.219 1.823,1.219 1.896,1.167 false 1.906,0.646 2.063,0.802 0.156,0.156 10 false 1 1.385,1.958 1.615,2.135 0.229,0.177 10 false 3 0.083,0.25 0.24,0.406 0.156,0.156 10 false 4 2.938,0.146 3.094,0.302 0.156,0.156 10 false 7 3.156,0.781 3.313,0.938 0.156,0.156 10 false 8 3.073,1.708 3.229,1.865 0.156,0.156 10 false 9 2.5,1.958 2.865,2.125 0.365,0.167 10 false 10 0.458,1.948 0.844,2.146 0.385,0.198 10 false 11 0.083,1.125 0.417,1.323 0.333,0.198 10 false 12 1.313,0.26 1.469,0.417 0.156,0.156 10 true 5 1.802,0.229 1.958,0.385 0.156,0.156 10 true 6 2.469,0.031 2.625,0.219 0.156,0.188 10 true 2 0.083,1.51 0.188,1.656 0.104,0.146 10 false A 1.719,1.406 2.031,1.604 0.313,0.198 10 false *1
*1 Seal Washer


Install the cylinder head cover sub-assembly with the 12 bolts and a new seal washer.

Torque:
Bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
Except bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

After tightening all bolts, check the tightening torque of 1 and 11. Retighten the bolt if necessary.



Hide 11202 42.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.
A187886C02
1.063,1.542 1.24,1.552 false
V100135

Seal Packing


Apply seal packing as shown in the illustration.

Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the cylinder head cover sub-assembly LH within 3 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




b.
A129705

Install 3 new gaskets as shown in the illustration.


c.

Install a new No. 2 cylinder head cover gasket to the cylinder head cover sub-assembly LH.


d.
A306349C01
0.427,1.625 0.427,1.479 0.427,1.479 1.469,1.479 true 0.906,1.844 0.906,1.49 false 1.25,1.677 1.25,1.479 false 1.76,1.115 2,0.927 2,0.927 2.156,0.927 false 1.563,1.344 1.719,1.542 0.156,0.198 10 false A 1.833,0.75 1.99,0.948 0.156,0.198 10 false 1 1.24,0.052 1.396,0.25 0.156,0.198 10 false 2 2.99,1.927 3.146,2.125 0.156,0.198 10 false 3 2.333,1.979 2.49,2.177 0.156,0.198 10 false 4 0.115,0.938 0.271,1.135 0.156,0.198 10 false 5 0.146,0.344 0.302,0.542 0.156,0.198 10 false 6 1.604,0.073 1.76,0.271 0.156,0.198 10 false 7 2.365,0.146 2.521,0.344 0.156,0.198 10 false 8 3.219,0.323 3.375,0.521 0.156,0.198 10 false 9 1.01,1.979 1.323,2.177 0.313,0.198 10 false 10 0.458,1.979 0.771,2.177 0.313,0.198 10 false 11 1.323,1.979 1.635,2.177 0.313,0.198 10 false 12 2.188,0.833 2.5,1.031 0.313,0.198 10 false *1
*1 Seal Washer


Install the cylinder head cover sub-assembly LH with the 12 bolts and a new seal washer.

Torque:
Bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
Except bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:

After tightening all bolts, check the tightening torque of 1 and 10. Retighten the bolt if necessary.



Hide 16331 43.INSTALL WATER OUTLET

a.
A129677

Install 2 new gaskets and a new O-ring.

HINT:

Apply soapy water to the O-ring.



b.
A268436C06
2.448,0.333 2.76,0.531 0.313,0.198 10 false *1 1.875,1.51 2.188,1.708 0.313,0.198 10 false *2 1.521,1.521 1.833,1.719 0.313,0.198 10 false *2 0.896,0.365 1.208,0.563 0.313,0.198 10 false *1 0.844,1.583 1.156,1.792 0.313,0.208 10 false *1 2.563,1.542 2.875,1.75 0.313,0.208 10 false *1
*1 Nut
*2 Bolt


Install the water outlet with the 2 bolts and 4 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Be careful that the O-ring does not get caught between the parts.



Hide 11452 44.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A171897

Apply a light coat of engine oil to a new O-ring and install it to the engine oil level dipstick guide.


b.
A210128

Install the engine oil level dipstick guide.


Hide 15781 45.INSTALL NO. 1 OIL COOLER BRACKET

a.
A139009N02
1.427,2.146 2.094,2.333 0.667,0.188 10 false 16 mm 1.427,2.802 2.135,2.969 0.708,0.167 10 false 12 mm 2.406,2.469 3.094,2.667 0.688,0.198 10 false 34 mm 1.427,2.302 3.115,2.5 1.688,0.198 10 false (0.630 in.) 1.427,2.958 3.115,3.156 1.688,0.198 10 false (0.472 in.) 2.406,2.625 3.042,2.865 0.635,0.24 10 false (1.34 in.)

Using an E8 "TORX" socket, install the 2 stud bolts as shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
A268435C04
2.833,0.438 3.146,0.635 0.313,0.198 10 false *1 2.896,1.063 3.208,1.26 0.313,0.198 10 false *2 2.573,1.25 2.885,1.448 0.313,0.198 10 false *1
*1 Nut
*2 Bolt


Install a new gasket to the No. 1 oil cooler bracket.


c.

Install the oil cooler pipe with the bolt and 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.
A268434C01
3.01,0.198 2.615,0.198 2.615,0.198 2.406,0.229 true 3.052,0.125 3.25,0.302 0.198,0.177 10 true *1
*1 Stud Bolt


Using an E7 "TORX" socket wrench, install the stud bolt as shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

Install a new gasket to the oil pan sub-assembly.


f.

Install the No. 1 oil cooler bracket with oil cooler pipe with the 3 bolts and 3 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 15710 46.INSTALL OIL COOLER ASSEMBLY

Hide 04152 48.INSTALL OIL FILTER CAP ASSEMBLY

Hide 11415 49.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.
A076531C14
2.271,0.969 2.542,1.313 false 2.531,1.385 2.844,1.583 0.313,0.198 10 false *a
*a Adhesive


for Bank 1:

i.

Apply adhesive to the cylinder block water drain cock sub-assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



ii.
A305236C02
0.135,0.104 0.448,0.302 0.313,0.198 12 false *A 2.938,0.917 3.292,1.135 0.354,0.219 10 false 20° 2.927,1.115 3.188,1.344 0.26,0.229 10 false 12°
*A for Bank 1


Install the cylinder block water drain cock sub-assembly as shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

Do not rotate the cylinder block water drain cock sub-assembly more than 1 revolution (360°) after tightening the cylinder block water drain cock sub-assembly to the specified torque.



iii.

Install the cylinder block water drain cock plug to the cylinder block water drain cock sub-assembly.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)



b.
A076531C14
2.271,0.969 2.542,1.313 false 2.531,1.385 2.844,1.583 0.313,0.198 10 false *a
*a Adhesive


for Bank 2:

HINT:

Perform this operation only when a cylinder block water drain cock sub-assembly is installed.


i.

Apply adhesive to the cylinder block water drain cock sub-assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



ii.
A305237C02
0.135,0.104 0.448,0.302 0.313,0.198 12 false *A 2.198,1.354 2.49,1.604 0.292,0.25 10 false 45° 2.625,1.354 2.906,1.594 0.281,0.24 10 false 15°
*A for Bank 2


Install the cylinder block water drain cock sub-assembly as shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:

Do not rotate the cylinder block water drain cock sub-assembly more than 1 revolution (360°) after tightening the cylinder block water drain cock sub-assembly to the specified torque.



iii.

Install the cylinder block water drain cock plug to the cylinder block water drain cock sub-assembly.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)



Hide 11415 50.INSTALL TAPER SCREW PLUG

HINT:

Perform this operation only when a taper screw plug is installed.


a.

Apply adhesive to the taper screw plug.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.

Install the taper screw plug to the cylinder block sub-assembly.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 15771 51.INSTALL NO. 1 OIL PIPE

a.

Make sure that there is no foreign matter on the mesh of the oil control valve filter LH.

NOTICE:

Do not touch the mesh when installing the oil control valve filter LH.



b.
A306342C01
1.354,0.708 1.667,0.906 0.313,0.198 10 false *1 2.052,1.885 2.365,2.083 0.313,0.198 10 false *1
*1 Oil Pipe Union


Install the oil control valve filter LH to the oil pipe union. Install 2 new gaskets and temporarily install the No. 1 oil pipe (on the cylinder head cover sub-assembly side) with the oil pipe union.


c.

Install a new gasket and temporarily install the oil pipe (on the cylinder head sub-assembly side) with the oil pipe union.


d.

Tighten the oil pipe union (on the cylinder head cover sub-assembly side).

Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)


e.

Tighten the oil pipe union (on the cylinder head sub-assembly side).

Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)

NOTICE:

If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.



Hide 15771M 52.INSTALL OIL PIPE

a.

Make sure that there is no foreign matter on the mesh of the oil control valve filter RH.

NOTICE:

Do not touch the mesh when installing the oil control valve filter RH.



b.
A200607C05
1.677,0.604 1.844,0.76 0.167,0.156 10 false *1 1.521,1.667 1.75,1.823 0.229,0.156 10 false *1 2.333,1.135 2.573,1.302 0.24,0.167 10 false *2
*1 Oil Pipe Union
*2 Bolt


Install the oil control valve filter RH to the oil pipe union. Install 2 new gaskets and temporarily install the oil pipe (on the cylinder head cover sub-assembly side) with the oil pipe union.


c.

Install a new gasket and temporarily install the oil pipe (on the cylinder head sub-assembly side) with the oil pipe union.


d.

Install the bolt to the cylinder head sub-assembly.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

Tighten the oil pipe union (on the cylinder head cover sub-assembly side).

Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)


f.

Tighten the oil pipe union (on the cylinder head sub-assembly side).

Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)

NOTICE:

If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.



Hide 54.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 12204 56.INSTALL VENTILATION VALVE SUB-ASSEMBLY

a.

Apply adhesive to the ventilation valve sub-assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



b.
A129655

Using a 19 mm deep socket wrench, install the ventilation valve sub-assembly.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 12108 58.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install a new oil filler cap gasket.


b.

Install the oil filler cap sub-assembly.