Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › from 2015.04
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075054 SMART ENTRY AND START SYSTEM(for Start Function) J

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  Power Source Mode does not Change to ON (READY)  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the vehicle and the power switch is pressed, the power management control ECU receives a signal and changes the power source mode. In addition, when the shift lever is in P and the brake pedal is depressed, the hybrid control system can be started by pressing the power switch.

HINT:
·

When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) auxiliary battery terminal, the power source mode changes to on (IG).

·

When the auxiliary battery cable is disconnected and reconnected, the power source returns to the mode it was in before the auxiliary battery cable was disconnected.



CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>CUSTOMIZE PARAMETERS).

·

Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly), refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

If the steering lock ECU (steering lock actuator assembly) is replaced, be sure to confirm that the steering is unlocked by turning the steering wheel to the left and right before starting the hybrid control system. If the steering is locked for any reason, open and close a door with the power switch off, and then unlock the steering by pressing the power switch. This prevents the hybrid control system from starting while the steering is locked.

·

After completing repairs, confirm that the problem does not occur.



HINT:
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to ON (READY)
Power Source Control
·

Stop Light Switch1

·

Steering Unlock Switch

·

Power Supply Condition

·

IG1 Relay Monitor(Inside)

·

IG2 Relay Monitor(Inside)

·

IG1 Relay Monitor(Outside)

·

IG2 Relay Monitor(Outside)

·

Latch Circuit

·

Shift P Signal

·

Starter Request Signal


Entry&Start
·

L Code Check

·

Engine Start Request


-


PROCEDURE

1.CHECK HYBRID CONTROL SYSTEM (READY ON)
a.

Place the electrical key transmitter sub-assembly on the driver seat.


b.

Depress the brake pedal.


c.

Confirm that the smart warning light is displayed, and then press the power switch and check that the hybrid system turns on (READY).

OK:

Power source mode becomes on (READY).



Result:
Proceed to
OK
NG



OK

END (HYBRID SYSTEM PERMISSION CONDITIONS WERE NOT SATISFIED)

NG

2.CHECK AUXILIARY BATTERY
2.CHECK AUXILIARY BATTERY
a.

Measure the auxiliary battery voltage with the power switch off.

Standard voltage:

11 to 14 V


HINT:
·

It may be possible to tell whether the auxiliary battery is discharged by operating the horn.

·

If the auxiliary battery voltage is less than 11 V, charge or replace it.




Result:
Proceed to
NEXT



NEXT

3.CHECK FOR DTC (ALL)
3.CHECK FOR DTC (ALL)
a.

Using the intelligent tester, confirm the output of DTCs for all systems.

OK:

No DTCs are output.


NOTICE:

Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.



Result:
Proceed to
OK
NG



OK

4.CHECK WAVE ENVIRONMENT

NG

GO TO DTC CHART

4.CHECK WAVE ENVIRONMENT
a.

If the problem occurs in certain locations or times of day, the possibility of wave interference is high.

HINT:

Whether or not the problem is due to wave interference can be checked by holding the electrical key transmitter sub-assembly near the door control receiver (RF band).



Result:
Proceed to
NEXT



NEXT

5.CHECK POWER SWITCH CONDITION
5.CHECK POWER SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

With the brake pedal released, check that pressing the power switch causes the power source mode to change.


Result:
Result Proceed to
Off → on (ACC) → on (IG) → off A
Power source mode does not change to on (ACC) and on (IG) B
Power source mode changes to on (IG) but not to on (ACC) C
Power source mode changes to on (ACC) but not to on (IG) D



A

6.READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH)

B

C

D

6.READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Switch State of steering unlock sensor signal output from steering lock actuator assembly ON or OFF ON: Steering unlocked
OFF: Steering locked
·

When the shift lever is in P and the power switch is off, if any door is opened or closed, the steering is locked.

·

When the electrical key transmitter sub-assembly is inside the vehicle and the power switch is turned on (ACC) or on (IG), the steering unlocks.

·

The hybrid control system cannot be started when the steering unlock signal is off.


Body Electrical > Power Source Control > Data List
Tester Display
Steering Unlock Switch
50003 223 2
OK:

The item in the Data List indicates "ON" (the steering is unlocked).



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH1)

NG

7.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH1)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch1 State of brake pedal ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
·

Use this item to determine whether the stop light switch is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.

·

When this item is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch1
50003 223 3
OK:

The item in the Data List changes when the brake pedal is depressed and released.



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)

NG

17.INSPECT STOP LIGHT SWITCH ASSEMBLY
8.READ VALUE USING INTELLIGENT TESTER (L CODE CHECK)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
L Code Check Verification result between certification ECU (smart key ECU assembly) and steering lock ECU (steering lock actuator assembly) OK or NG OK: Verification result normal
NG: Verification result abnormal
When NG is displayed:
·

L code has not been registered for the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly).

·

Steering wheel cannot be locked.

·

Steering wheel cannot be unlocked (the hybrid control system cannot be started).


Body Electrical > Entry&Start > Data List
Tester Display
L Code Check
50003 125 66
OK:

The Data List item changes to "OK" when the electrical key transmitter sub-assembly is inside the vehicle.


HINT:

Reasons for verification failure:

·

The steering lock ECU (steering lock actuator assembly) is malfunctioning.

·

There is a problem with the communication between ECUs.

·

An ECU is replaced, but is not registered.

·

An ECU is replaced with an ECU which has a code already stored in it.




Result:
Proceed to
OK
NG



OK

9.READ VALUE USING INTELLIGENT TESTER (STARTER REQUEST SIGNAL)

NG

15.CHECK STEERING LOCK ACTUATOR ASSEMBLY
9.READ VALUE USING INTELLIGENT TESTER (STARTER REQUEST SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Entry&Start / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Entry&Start > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Start Condition Status of hybrid control system start permission signal determined by steering lock ECU (steering lock actuator assembly) and sent to certification ECU (smart key ECU assembly) OK or NG OK: Hybrid control system start permitted
NG: Hybrid control system start prohibited
·

When OK is displayed, the certification ECU (smart key ECU assembly) receives an unlock confirmation signal from the steering lock ECU (steering lock actuator assembly) and hybrid control system starting possible.

·

The hybrid control system cannot be started when NG is displayed.


Body Electrical > Entry&Start > Data List
Tester Display
Engine Start Condition
50003 125 49
NOTICE:

Check that the smart warning is displayed on the multi-information display on the combination meter assembly, and then press the power switch.


OK:

The display changes in response to the operation of the power switch.



Result:
Proceed to
OK
NG



OK

10.CHECK ENGINE IMMOBILISER SYSTEM

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

10.CHECK ENGINE IMMOBILISER SYSTEM
a.
B231391C19
2.417,0.26 2.833,0.5 0.417,0.24 1.875,0.26 2.292,0.5 0.417,0.24 1.802,1.031 1.51,1.802 false 2.583,1.229 2.406,1.771 false 2.625,1.229 2.906,1.781 false 2.563,0.302 2.833,0.521 0.271,0.219 10 false I4 2.01,0.302 2.271,0.521 0.26,0.219 10 false I3 0.021,0.01 0.26,0.292 0.24,0.281 10 false *a 2.833,1.802 3.208,2.042 0.375,0.24 10 false IMO 2.292,1.802 2.594,2.031 0.302,0.229 10 false IMI 1.406,1.802 1.75,2.073 0.344,0.271 10 false E1
*a Component with harness connected(Power Management Control ECU)


Using the oscilloscope, check the waveform.

i.

Waveform 1

B325134C07
0.917,1.271 1.375,1.469 0.458,0.198 10 false GND 2.719,1.354 3.177,1.552 0.458,0.198 10 false *a 2.906,1.354 3.365,1.552 0.458,0.198 10 false *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition:
Item Content
Tester Connection I4-28 (IMO) - I3-6 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected



ii.

Waveform 2

B333259C08
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition:
Item Content
Tester Connection I4-29 (IMI) - I3-6 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of hybrid control system start or within 3 seconds of power switch turned on (IG) after auxiliary battery cable disconnected and reconnected


OK:

The waveform is displayed as shown in illustration.




Result:
Proceed to
OK
NG



OK

11.READ VALUE USING INTELLIGENT TESTER (STARTER REQUEST SIGNAL)

NG

12.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
11.READ VALUE USING INTELLIGENT TESTER (STARTER REQUEST SIGNAL)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Starter Request Signal Hybrid control system start request signal status ON or OFF ON: With the shift lever in P and brake pedal depressed, the power switch is pressed and held
OFF: After approx. 1 sec. has elapsed, the power switch is released
·

When the hybrid control system cannot be started due to a start request signal malfunction, OFF is displayed.

·

When the power switch is pressed, the duration of time that ON is displayed will be extremely short. As such, the power switch needs to be pressed and held for a certain amount of time.


Body Electrical > Power Source Control > Data List
Tester Display
Starter Request Signal
50003 223 12
NOTICE:

Check that the smart warning is displayed on the multi-information display on the combination meter assembly, and then press the power switch.


OK:

The display changes in response to the operation of the power switch.



Result:
Proceed to
OK
NG



OK

GO TO HYBRID CONTROL SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

NG

12.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the I4 connector from the power management control ECU.


b.

Disconnect the I87 connector from the certification ECU (smart key ECU assembly).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I4-28 (IMO) - I87-10 (EFII) Always Below 1 Ω
I4-29 (IMI) - I87-14 (EFIO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one (Refer to the Service Bulletin).


b.

Perform the registration procedures (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

14.CHECK HYBRID CONTROL SYSTEM (READY ON)
14.CHECK HYBRID CONTROL SYSTEM (READY ON)
a.

Place the electrical key transmitter sub-assembly on the driver seat.


b.

Depress the brake pedal.


c.

Confirm that the smart warning light is displayed, and then press the power switch and check that the hybrid system turns on (READY).

OK:

Power source mode becomes on (READY).



Result:
Proceed to
OK
NG



OK

END(CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) WAS DEFECTIVE)

NG

15.CHECK STEERING LOCK ACTUATOR ASSEMBLY
a.

Replace the steering lock ECU (steering lock actuator assembly) with a new one.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>DISASSEMBLY


b.

Perform the registration procedures (Refer to the Service Bulletin).


Result:
Proceed to
NEXT



NEXT

16.CHECK HYBRID CONTROL SYSTEM (READY ON)
16.CHECK HYBRID CONTROL SYSTEM (READY ON)
a.

Place the electrical key transmitter sub-assembly on the driver seat.


b.

Depress the brake pedal.


c.

Confirm that the smart warning light is displayed, and then press the power switch and check that the hybrid system turns on (READY).

OK:

Power source mode becomes on (READY).



Result:
Proceed to
OK
NG



OK

END (STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

17.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Disconnect the A33 connector from the stop light switch assembly.


b.

Inspect the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

18.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STOP LIGHT SWITCH ASSEMBLY)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR