Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM (w/ EGR System)

DTC    P3190    Poor Engine Power

DTC    P3191    Engine does not Start

for Preparation Click here


DESCRIPTION

The ECM receives signals from the power management control ECU such as the requested engine torque, target engine speed and engine cranking status, and controls the engine output based on the target engine speed and requested torque.

DTC No.
DTC Detection Condition
Trouble Area
P3190
When all of the following conditions are met (1 trip detection logic):
  1. Engine speed is 650 rpm or more (varies depending on the engine coolant temperature).
  2. Engine torque requested by the power management control ECU exceeds a certain level.
  3. The power management control ECU judges that the engine has started.
  4. The fuel tank is not empty.
  5. Communication between the power management control ECU and ECM is normal.
  6. "The actual engine torque is less than 20% of the requested engine torque" for 6 seconds, or until the crankshaft rotates 100 times (whichever takes longer, differs depending on the engine coolant temperature).
  1. Intake system
  2. Throttle with motor body assembly
  3. Fuel system
  4. Engine
  5. Mass air flow meter sub-assembly
  6. Out of fuel
  7. Engine coolant temperature sensor
  8. Crankshaft position sensor
  9. Camshaft position sensor
  10. EGR valve assembly
  11. ECM
P3191
When all of the following conditions are met (1 trip detection logic):
  1. Engine speed is 650 rpm or more (varies depending on the engine coolant temperature).
  2. The fuel tank is not empty.
  3. Communication between the power management control ECU and ECM is normal.
  4. After the power management control ECU sends the engine start request signal, it does not detect engine start (generation of engine torque) for 6 seconds, or until the crankshaft rotates 100 times (whichever takes longer, differs depending on the engine coolant temperature).
  1. Intake system
  2. Throttle with motor body assembly
  3. Fuel system
  4. Engine
  5. Mass air flow meter sub-assembly
  6. Out of fuel
  7. Engine coolant temperature sensor
  8. Crankshaft position sensor
  9. Camshaft position sensor
  10. EGR valve assembly
  11. ECM

MONITOR DESCRIPTION

  1. The ECM receives signals such as requested engine torque, target engine speed and engine cranking status from the power management control ECU.
  2. The ECM controls engine start and stop and the throttle valve angle based on the signals received from the power management control ECU.
  3. The ECM receives the actual engine torque calculated by the power management control ECU based on the generator torque.
  4. When the actual engine torque is less than 20% of the requested engine torque*1, the ECM judges that engine output is abnormal and stores DTC P3190.
    (The engine may not have started in the above condition.)
    1. *1: Requested torque = Requested Engine Torque (kW) / HV Target Engine Speed (rpm) x 9549
  5. If the ECM does not detect engine start torque (actual engine torque) even though it has received an engine start request and started the engine, it stores DTC P3191.

    HINT:
    1. When DTC P3190, P3191 or P3193 is stored, engine operation is disabled. In this case, add fuel or perform a repair, then clear the DTCs and turn the power switch off to allow the operation to return to normal.
    2. When DTC P3190, P3191 or P3193 is stored, the HV battery is not charged as the vehicle operates using only the motor. If the vehicle is driven in this condition, SOC will drop and the HV battery will be depleted, preventing the system from entering the READY-on state.
    3. When DTC P3190 or P3191 is stored, the engine torque has dropped by 80% or the engine cannot be started. If any DTCs that indicate malfunctioning of engine related parts are stored at the same time, repair the malfunctioning parts first.
      Relevant Data List Items:


ECM (Powertrain / Engine and ECT / Data List)
HV Target Engine Speed
Engine Speed
Requested Engine Torque
Actual Engine Torque
Throttle Position Command
Throttle Position No. 1
Calculate Load
Coolant Temp
Short FT #1
Long FT #1
-
-

POWER MANAGEMENT CONTROL ECU (Powertrain / Hybrid Control / Data List)
Target Engine Rev
Engine Revolution
Requested Engine Torque
Engine Coolant Temp
Engine Idling Request
-
-
-

MONITOR STRATEGY


Frequency of Operation
Continuous

CONFIRMATION DRIVING PATTERN

NOTICE:
If the MIL or master warning light illuminates, stop the road test immediately. When DTC P3190, P3191 or P3193 is stored, the vehicle can be driven only a short distance as the engine operation is disabled and the HV battery is not charged.


A299140E06

  1. Apply the parking brake firmly.
  2. Connect the GTS to the DLC3.
  3. Turn the power switch on (IG).
  4. Turn the GTS on.
  5. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  6. Turn the power switch off and wait for at least 30 seconds.
  7. Turn the power switch on (READY).
  8. Turn the GTS on.
  9. Fully depress the accelerator pedal for 10 seconds with the vehicle stopped, the shift lever in P and the brake pedal depressed. [A]

    NOTICE:
    As soon as the engine starts, release the accelerator pedal.

  10. Release the parking brake.
  11. Drive the vehicle at an average of approximately 40 km/h (25 mph) or more until the total engine operation time is 10 minutes or more. [B]

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    It is not necessary to maintain the vehicle speed at 40 km/h (25 mph) throughout the road test.

  12. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes. [C]
  13. Read the DTCs (including pending DTCs).

    HINT:
    1. If a DTC (including pending DTC) is output, the system is malfunctioning.
    2. If a DTC (including pending DTC) is not output, perform the following procedure.

  14. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  15. Input the DTC: P3190 or P3191.
  16. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.


INSPECTION PROCEDURE

HINT:
  1. Repeating this inspection for symptom confirmation may cause the SOC to drop, preventing the system from entering the READY-on state. In this case, use the THS charger to charge the HV battery.
  2. Cranking the engine once causes the SOC to drop approximately 1%.
  3. Charging the HV battery once (10 minutes) using the THS charger restores the SOC approximately 2%.
  4. Charging the HV battery using the THS charger takes approximately 10 minutes when the HV battery temperature is 25°C (77°F) or approximately 30 minutes when the HV battery temperature is 0°C (32°F).
  5. The THS charger is a supplemental charging device that charges the HV battery enough to enable the engine to start (the vehicle can enter the READY-on state).
  6. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P3190, P3191 AND/OR P3193)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P3190 or P3191 is output
    A
    DTC P3193 is output
    B
    DTC P3190, P3191 and/or P3193 and other DTCs are output
    C

    HINT:
    If any SFI system DTCs other than DTC P3190, P3191 or P3193 is output, perform troubleshooting for those DTCs first.



B
GO TO DTC P3193 (Click here)

C
GO TO DTC CHART (Click here)
A


2.CHECK SHORTAGE OF FUEL
  1. Check the amount of fuel remaining.

    OK:
    There is enough fuel.

    HINT:
    1. DTCs P3190, P3191 and/or P3193 may be output if the vehicle ran out of fuel in the past.
    2. If not enough fuel is added, DTC P3190, P3191 or P3193 may be output again. If the engine cannot be started because the vehicle is out of fuel, add fuel until the fuel level warning light turns off.



NG
REFILL FUEL
OK


3.CLEAR DTC
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs.

  1. Turn the power switch off and wait for at least 30 seconds.


NEXT


4.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leaks (Click here).

    OK:
    No leaks in intake system.

    HINT:
    Perform "Inspection After Repair" after repairing or replacing the intake system (Click here).



NG
REPAIR OR REPLACE INTAKE SYSTEM
OK


5.CHECK FOR UNUSUAL NOISE OR VIBRATION WHEN STARTING ENGINE OR REVVING UP

OK:
Unusual noise and vibration do not occur.



NG
REPAIR OR REPLACE MALFUNCTIONING PART
OK


6.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
CHECK FUEL PUMP CONTROL CIRCUIT (Click here)
OK


7.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY
  1. Inspect the throttle with motor body assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the throttle with motor body assembly (Click here).



NG
REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY (Click here)
OK


8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY
  1. Inspect the mass air flow meter sub-assembly (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly (Click here).



NG
REPLACE MASS AIR FLOW METER SUB-ASSEMBLY (Click here)
OK


9.INSPECT ENGINE COOLANT TEMPERATURE SENSOR
  1. Inspect the engine coolant temperature sensor (Click here).

    HINT:
    Perform "Inspection After Repair" after replacing the engine coolant temperature sensor (Click here).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


10.INSPECT CRANKSHAFT POSITION SENSOR
  1. Inspect the crankshaft position sensor (Click here).



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


11.REPLACE CAMSHAFT POSITION SENSOR
  1. Replace the camshaft position sensor (Click here).


NEXT


12.CHECK WHETHER DTC OUTPUT RECURS (DTC P3190 OR P3191)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Turn the power switch on (READY).

  1. Turn the GTS on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    DTC P3190 or P3191 is output
    A
    DTCs are not output
    B



B
END
A


13.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION)
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Put the engine in inspection mode (maintenance mode) (Click here).

  1. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

    HINT:
    The A/C switch and all accessory switches should be off and shift lever in P or N.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / All Data / MAP and Throttle Idle Position.

  1. Confirm that Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.

    HINT:
    1. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    2. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    3. Do not open the EGR valve 30 steps or more during the Active Test.

    OK:
    MAP change in response to EGR step position when Throttle Idle Position is ON in the Data List.


    Standard:

    -
    EGR Step Position (Active Test)
    0 Steps
    0 to 30 Steps
    MAP
    (Data List)
    (EGR valve is fully closed)
    MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed

    HINT:
    1. If the Active Test cannot be performed due to a malfunction such as the engine not starting, perform the EGR valve assembly inspection in the following step.
    2. While performing the Active Test, if the increase in the value of MAP is small, the EGR valve assembly may be a malfunctioning.
    3. Even if the EGR valve assembly is malfunctioning, rough idling or an increase in the value of MAP may occur while performing the Active Test. However, the amount that the value of MAP increases will be smaller than normal.


    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
Go to step 15
A


14.INSPECT EGR VALVE ASSEMBLY
  1. Remove the EGR valve assembly (Click here).

  1. Check if the EGR valve is stuck open.

    OK:
    EGR valve is tightly closed.

    HINT:
    Perform "Inspection After Repair" after replacing the EGR valve assembly (Click here).



NG
REPLACE EGR VALVE ASSEMBLY (Click here)
OK


15.REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


16.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Turn the power switch on (IG).

  1. Turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the power switch off and wait for at least 30 seconds.

  1. Turn the power switch on (READY).

  1. Turn the GTS on.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.


NEXT

END