DTC P21951D O2 Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Circuit Current Out of Range |
DTC P219523 O2 Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Signal Stuck Low |
DTC P21961D O2 Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Circuit Current Out of Range |
DTC P219624 O2 Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Signal Stuck High |

| DTC No. | DTC Detection Condition | Trouble Area |
| P21951D | While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is 2.2 mA or higher for 3 seconds or more (2 trip detection logic). |
|
| P219523 | Both of the following conditions are met for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor voltage is higher than 3.8 V. (b) Heated oxygen sensor voltage is 0.21 V or higher. |
|
| P21961D | While the fuel-cut operation is performed (during vehicle deceleration), the air fuel ratio sensor current is less than 0.47 mA for 3 seconds or more (2 trip detection logic). |
|
| P219624 | Both of the following conditions are met for 5 seconds or more (2 trip detection logic): (a) Air fuel ratio sensor voltage is less than 2.8 V. (b) Heated oxygen sensor voltage is less than 0.69 V. |
|

| Required Sensors/Components (Main) | Air fuel ratio sensor |
| Required Sensors/Components (Related) | Heated oxygen sensor |
| Frequency of Operation | Continuous: Sensor voltage detection monitor Once per driving cycle: Sensor current detection monitor |
| Duration | 3 seconds: Sensor current detection monitor 5 seconds: Sensor voltage detection monitor |
| Time after engine start | 30 seconds or more |
| Fuel system status | Closed loop |
| Battery voltage | 11 V or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [570 mmHg(abs)] or higher |
| Air fuel ratio sensor status | Activated |
| Continuous time of fuel-cut | 3 seconds or more, and less than 10 seconds |
| Heated oxygen sensor voltage | 0.21 V or higher |
| Air fuel ratio sensor voltage | Higher than 3.8 V |
| Heated oxygen sensor voltage | Less than 0.69 V |
| Air fuel ratio sensor voltage | Less than 2.8 V |
| Air fuel ratio sensor current | 2.2 mA or higher |
| Air fuel ratio sensor current | Less than 0.47 mA |


| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P21951D, P219523, P21961D OR P219624) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P21951D, P219523, P21961D or P219624 is output | A |
| DTC P21951D, P219523, P21961D or P219624 and P013613, P013617 or P01361C are output | |
| DTC P21951D, P219523, P21961D or P219624 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST |
Has the vehicle run out of fuel in the past?
|
| ||||
| YES | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P21951D, P219523, P21961D OR P219624) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P21951D, P219523, P21961D or P219624.
Check the DTC judgment.
| Result | Proceed to |
| NORMAL (DTCs are not output) | A |
| ABNORMAL (DTC P21951D, P219523, P21961D or P219624 is output) | B |
|
| ||||
| A | ||
| ||
| 4.READ VALUE USING GTS (A/F (O2) SENSOR CURRENT B1S1) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Enter the following menus: Powertrain / Engine / Data List / All Data / A/F (O2) Sensor Current B1S1.
Check the test value of the air fuel ratio sensor output current during fuel-cut, referring to the Driving Pattern Detail for [C] through [E] in the Confirmation Driving Pattern.
| Test Value | Proceed to |
| Within normal range (0.47 mA or higher, and less than 2.2 mA) | A |
| Outside normal range (less than 0.47 mA, or 2.2 mA or higher) | B |
|
| ||||
| A | |
| 5.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.
Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.
Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2) displayed on the GTS.
| GTS Display (Sensor) | Injection Volume | Status | Voltage |
| A/F (O2) Sensor Voltage B1S1 (Air fuel ratio) | 12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2 Sensor Voltage B1S2 (Heated oxygen) | 12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Status of A/F (O2) Sensor Voltage B1S1 | Status of O2 Sensor Voltage B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Proceed to |
| Lean | Lean | Actual air fuel ratio lean | A |
| Rich | Rich | Actual air fuel ratio rich | |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | |
| Lean/Rich | Lean/Rich | Normal |
|
| ||||
| A | |
| 6.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 7.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 8.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE) |
Check the fuel pressure (for low pressure side) .
|
| ||||
| OK | |
| 9.INSPECT FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION) |
Inspect the fuel injector assembly (for port injection) (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 10.READ VALUE USING GTS (FUEL PRESSURE (HIGH)) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine / Data List / All Data / Fuel Pressure (High).
Read the values.
|
| ||||
| OK | |
| 11.INSPECT FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION) |
Inspect the fuel injector assembly (for direct injection) (Click here).
|
| ||||
| OK | |
| 12.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 13.CHECK WHETHER DTC OUTPUT RECURS (DTC P21951D, P219523, P21961D OR P219624) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P21951D, P219523, P21961D or P219624.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P21951D, P219523, P21961D or P219624 is output) | A |
| NORMAL (DTCs are not output) | B |
|
| ||||
| A | |
| 14.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / All Data / Engine Speed and Intake Manifold Absolute Pressure.
Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| Idling condition | Steady idling | Idling changes from steady to rough idling or engine stalls |
| Intake Manifold Absolute Pressure (Data List) | Intake Manifold Absolute Pressure value is 20 to 40 kPa(abs) (150 to 300 mmHg(abs)) (EGR valve is fully closed) | Intake Manifold Absolute Pressure value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
|
| ||||
|
| ||||
| 15.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | |
| 16.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P21951D, P219523, P21961D or P219624.
Check the DTC judgment result.
| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| NEXT | ||
| ||
| 18.CHECK FUEL LINE (FOR LOW PRESSURE SIDE) |
Check the fuel lines for leaks or blockage.
|
| ||||
| OK | ||
| ||
| 19.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 20.CHECK WHETHER DTC OUTPUT RECURS (DTC P21951D, P219523, P21961D OR P219624) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P21951D, P219523, P21961D or P219624.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTCs are not output) | A |
| ABNORMAL (DTC P21951D, P219523, P21961D or P219624 is output) | B |
|
| ||||
| A | ||
| ||