Home › Engine / Hybrid System › 6AR-FSE (LUBRICATION) › OIL PUMP › 2018.04–2021.02
RM33A0E _51 Engine / Hybrid System _072208 6AR-FSE LUBRICATION _0351652 OIL PUMP A

6AR-FSE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 11302 1.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.
A337955C01
0.74,1.719 0.938,1.917 0.198,0.198 10 true *1 2.729,1.417 3.042,1.573 0.313,0.156 10 true *2 2.375,1.74 2.688,1.896 0.313,0.156 10 true *1
*1 Oil Pump Gasket
*2 Oil Hole Cover Gasket


Apply a light coat of engine oil to 2 new oil pump gaskets and a new oil hole cover gasket.


b.

Install the 2 oil pump gaskets and oil hole cover gasket to the stiffening crankcase assembly.


c.
A337953C01
0.938,3.073 1.188,3.26 1.188,3.26 1.469,3.26 true 2.292,2.938 2.542,3.125 2.542,3.125 2.823,3.125 true 1.51,3.188 1.823,3.344 0.313,0.156 10 false *1 2.854,3.052 3.167,3.208 0.313,0.156 10 false *2
*1 Drive Rotor Spline
*2 Crankshaft Timing Sprocket


Align the drive rotor spline and the crankshaft timing sprocket as shown in the illustration.


d.

Apply seal packing in a line to the timing chain cover sub-assembly as shown in the following illustration.

A337282C01
5.073,1.396 5.271,1.396 5.271,1.396 5.521,1.573 false 5.896,3.5 6.156,3.302 6.156,3.302 6.302,3.302 false 6.094,5.719 6.354,5.521 6.354,5.521 6.5,5.521 false 2.729,7.229 3.26,7.229 false 4.844,3.604 5.156,3.76 0.313,0.156 10 false *a 5.688,2.938 6,3.094 0.313,0.156 10 false *b 5.813,5.063 6.125,5.219 0.313,0.156 10 false *c 3.635,0.427 4.115,0.823 0.479,0.396 10 false A - A 0.51,0.417 0.99,0.813 0.479,0.396 10 false A - A 0.5,0.802 0.979,1.198 0.479,0.396 10 false B - B 2.885,0.771 3.25,0.958 0.365,0.188 10 true B - B 0.979,1.708 1.344,1.885 0.365,0.177 10 true C - C 3.448,1.708 3.802,1.875 0.354,0.167 10 true C - C 5.052,0.74 5.531,1.135 0.479,0.396 10 false A - A 4.521,2.865 5.573,3.188 1.052,0.323 10 false B - B, D - D 0.875,3.813 1.344,4.219 0.469,0.406 10 false D - D 2.781,3.802 3.135,3.979 0.354,0.177 10 true D - D 4.719,5.031 5.198,5.427 0.479,0.396 10 false C - C 2.375,5.177 2.854,5.573 0.479,0.396 10 false E 2.583,2.625 2.771,2.844 0.188,0.219 10 true E 4.323,5.875 4.635,6.031 0.313,0.156 10 false *a 6.083,1 6.781,1.24 0.698,0.24 10 false 2.5 mm 4.177,1.302 5.156,1.521 0.979,0.219 10 false 2.5 to 3.5 mm 6.292,4.031 6.99,4.271 0.698,0.24 10 false 3.0 mm 6.354,3.219 7.052,3.458 0.698,0.24 10 false 5.0 mm 6.552,5.448 7.083,5.781 0.531,0.333 10 false 7.0 mm 6.521,6.229 7.135,6.531 0.615,0.302 10 false 5.0 mm 3.302,7.156 4.281,7.375 0.979,0.219 10 false 2.5 to 3.5 mm 1.771,7.052 2.469,7.292 0.698,0.24 10 false 3.0 mm 4.021,1 4.719,1.24 0.698,0.24 10 false 28 mm 4.042,1.927 4.74,2.167 0.698,0.24 10 false 25 mm 4.052,4.01 4.75,4.25 0.698,0.24 10 false 26 mm 2.479,1.177 2.667,1.396 0.188,0.219 10 true E
*a 3.0 mm or more *b 7.0 mm or more
*c 13 mm or more - -


Seal Packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal Packing Application Chart:
Area Seal Packing Diameter (Round) Distance from Edge of Cover to Center of Seal Packing Seal Packing Application Length
Seal Packing Dimension (Flat)
Dashed Line 2.5 to 3.5 mm (0.0984 to 0.138 in.) 2.5 mm (0.0984 in.) -
-
(A) - (A) 2.5 to 3.5 mm (0.0984 to 0.138 in.) 2.5 mm (0.0984 in.) -
-
(B) - (B) 5.0 mm (0.197 in.) 3.0 mm (0.118 in.) 28 mm (1.10 in.)
7.0 mm (0.276 in.) or wider and 3.0 mm (0.118 in.) or thicker
(C) - (C) 7.0 mm (0.276 in.) 5.0 mm (0.197 in.) 25 mm (0.984 in.)
13 mm (0.512 in.) or wider and 3.0 mm (0.118 in.) or thicker
(D) - (D) 5.0 mm (0.197 in.) 3.0 mm (0.118 in.) 26 mm (1.02 in.)
7.0 mm (0.276 in.) or wider and 3.0 mm (0.118 in.) or thicker
(E) 2.5 to 3.5 mm (0.0984 to 0.138 in.) 3.0 mm (0.118 in.) -
-


NOTICE:
·

Clean the surfaces with non-residue solvent before applying seal packing.

·

Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes of applying seal packing.

·

After applying seal packing to the timing chain cover sub-assembly, install the engine mounting bracket RH within 10 minutes.

·

Do not add oil for at least 2 hours after installation.

·

Do not start the engine for at least 2 hours after installation.




e.

Temporarily install the timing chain cover sub-assembly with the 17 bolts and 2 nuts.

A337954C01
0.906,0.156 1.063,0.354 0.156,0.198 10 false A 0.875,0.49 1.031,0.688 0.156,0.198 10 false A 0.927,0.833 1.083,1.031 0.156,0.198 10 false B 0.969,1.031 1.125,1.229 0.156,0.198 10 false B 0.938,1.229 1.094,1.427 0.156,0.198 10 false A 0.823,1.531 0.979,1.729 0.156,0.198 10 false A 0.854,1.865 1.01,2.063 0.156,0.198 10 false A 0.854,2.177 1.01,2.375 0.156,0.198 10 false A 1.115,2.563 1.271,2.76 0.156,0.198 10 true A 2.844,0.479 3,0.677 0.156,0.198 10 false A 2.667,0.802 2.823,1 0.156,0.198 10 false B 2.625,1.042 2.781,1.24 0.156,0.198 10 true B 2.563,1.5 2.719,1.698 0.156,0.198 10 true A 2.656,1.844 2.813,2.042 0.156,0.198 10 true A 2.646,2.156 2.802,2.354 0.156,0.198 10 true A 1.74,2.615 1.979,2.781 0.24,0.167 10 false A 0.521,0.083 0.833,0.417 0.313,0.333 10 false *a 3.833,0.083 4.146,0.417 0.313,0.333 10 false *b 4.094,0.167 4.385,0.406 0.292,0.24 10 false 18 4.073,0.49 4.365,0.729 0.292,0.24 10 false 17 4.167,0.833 4.458,1.073 0.292,0.24 10 false 4 4.208,1.021 4.5,1.26 0.292,0.24 10 false 2 4.125,1.219 4.417,1.458 0.292,0.24 10 false 16 4,1.542 4.292,1.781 0.292,0.24 10 false 15 4.052,1.896 4.344,2.135 0.292,0.24 10 false 14 4.073,2.177 4.365,2.417 0.292,0.24 10 false 13 4.323,2.552 4.552,2.75 0.229,0.198 10 true 12 6.115,0.188 6.406,0.427 0.292,0.24 10 false 5 6.052,0.5 6.344,0.74 0.292,0.24 10 false 6 5.896,0.792 6.188,0.99 0.292,0.198 10 true 3 5.854,1.031 6.146,1.229 0.292,0.198 10 true 1 5.792,1.5 6.083,1.698 0.292,0.198 10 true 7 5.906,1.875 6.198,2.073 0.292,0.198 10 true 8 5.896,2.188 6.188,2.385 0.292,0.198 10 true 9 5.552,2.542 5.844,2.74 0.292,0.198 10 true 10 5.219,1.656 5.51,1.854 0.292,0.198 10 true 19 4.938,2.625 5.229,2.792 0.292,0.167 10 false 11 2.052,1.667 2.208,1.865 0.156,0.198 10 true C
*a Torque *b Tightening Order
V100135

Bolt
V100136

Nut


Bolt Length:
Item Length Thread Diameter
Bolt (A) 30 mm (1.18 in.) 8.0 mm (0.315 in.)
Bolt (B) 35 mm (1.38 in.) 10 mm (0.394 in.)
Bolt (C) 45 mm (1.77 in.) 8.0 mm (0.315 in.)


NOTICE:

Make sure there is no oil on the bolts. If oil is found on any bolt, clean it before installation.



f.

Tighten the 17 bolts and 2 nuts in several steps, in the order shown in the illustration.

Torque:
Bolt (A), (C) and Nut : 21 N*m (214 kgf*cm, 15 ft.*lbf)
Bolt (B) : 55 N*m (561 kgf*cm, 41 ft.*lbf)


Hide 12315A 2.INSTALL ENGINE MOUNTING BRACKET RH

a.
A413666N01
1.552,1.51 1.708,1.708 0.156,0.198 10 true 1 0.771,0.604 0.927,0.813 0.156,0.208 10 true 2 2.198,0.594 2.354,0.802 0.156,0.208 10 true 3 1.063,1.438 1.219,1.646 0.156,0.208 10 true 4

Install the engine mounting bracket RH with the 4 bolts in the order shown in the illustration.

Torque:
Bolt (1), (2) and (3) : 55 N*m (561 kgf*cm, 41 ft.*lbf)
Bolt (4) : 21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

After applying seal packing to the timing chain cover sub-assembly, install the engine mounting bracket RH within 10 minutes.



Hide 16620 4.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 15370 5.INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 11201 8.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 25625 9.INSTALL EGR VALVE BRACKET

a.

Temporarily install the 2 EGR valve brackets with the 4 bolts.


b.
A340297N01
2.625,1.49 2.781,1.688 0.156,0.198 10 true 1 2.104,1.333 2.26,1.531 0.156,0.198 10 true 2 2.302,2.854 2.458,3.052 0.156,0.198 10 true 3 1.063,1.583 1.271,1.802 0.208,0.219 10 false 4

Tighten the 4 bolts in the order shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Install the fuel hose bracket to the EGR valve bracket with the engine cover joint.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 23021 10.TEMPORARILY INSTALL FUEL PUMP WITH SEAL SUB-ASSEMBLY

Hide 23801P 11.TEMPORARILY INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23021 12.INSTALL FUEL PUMP WITH SEAL SUB-ASSEMBLY

Hide 23801P 13.INSTALL NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 12262 17.CONNECT NO. 2 VENTILATION HOSE

Hide 19.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND