The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.
11310
1.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
17118
2.REMOVE MANIFOLD STAY
17139
3.REMOVE NO. 2 MANIFOLD STAY
17167
4.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
25051
5.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)
22030
6.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY
22271
7.REMOVE THROTTLE BODY GASKET
17650
8.REMOVE VACUUM SWITCHING VALVE ASSEMBLY (for ACIS)
23814B
9.REMOVE FUEL DELIVERY PIPE
23891
10.REMOVE FUEL DELIVERY SPACER
23291
11.REMOVE INJECTOR VIBRATION INSULATOR
23250
12.REMOVE FUEL INJECTOR ASSEMBLY
12262
13.DISCONNECT NO. 2 VENTILATION HOSE
17111
14.REMOVE INTAKE MANIFOLD
15.SET NO. 1 CYLINDER TO TDC/COMPRESSION
13566B
16.REMOVE TIMING CHAIN GUIDE
Remove the bolt and timing chain guide.
13540
17.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
| *a | Stopper Plate |
| *b | Plunger |
Allow the plunger to extend slightly, and then turn the stopper plate counterclockwise to release the lock. Once the lock is released, push the plunger into the No. 1 chain tensioner assembly.
| *a | Pin |
Move the stopper plate clockwise to set the lock, and insert a pin into the stopper plate hole.
Remove the 2 bolts, No. 1 chain tensioner assembly and gasket.
13559
18.REMOVE CHAIN TENSIONER SLIPPER
Remove the bolt and chain tensioner slipper.
13506
19.REMOVE CHAIN SUB-ASSEMBLY
Remove the chain sub-assembly.
13561
20.REMOVE NO. 1 CHAIN VIBRATION DAMPER
Remove the 2 bolts and No. 1 chain vibration damper.
13050
21.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
| *a | Hold |
| *b | Turn |
| *c | Do not remove |
Using a wrench to hold the hexagonal portion of the camshaft, remove the bolt and camshaft timing gear assembly.
Be careful not to damage the cylinder head sub-assembly or spark plug tube with the wrench.
Do not disassemble the camshaft timing gear assembly.
Do not remove the other 4 bolts.
13070A
22.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
| *a | Hold |
| *b | Turn |
Using a wrench to hold the hexagonal portion of the No. 2 camshaft, remove the bolt and camshaft timing exhaust gear assembly.
Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly or spark plug tube with the wrench.
11103
23.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY
Uniformly loosen and remove the 20 bolts in the order shown in the illustration.
Remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver.
Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.
Tape the screwdriver tip before use.
24.REMOVE CAMSHAFT BEARING CAP
| *1 | No. 1 Camshaft Bearing Cap |
| *2 | No. 2 Camshaft Bearing Cap |
| *3 | No. 3 Camshaft Bearing Cap |
Remove the 11 bolts in the order shown in the illustration.
Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap and 3 No. 3 camshaft bearing caps.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
15678A
25.REMOVE OIL CONTROL VALVE FILTER
11811
26.REMOVE NO. 1 CAMSHAFT BEARING
13511
27.REMOVE CAMSHAFT
Remove the camshaft from the camshaft housing sub-assembly.
13512
28.REMOVE NO. 2 CAMSHAFT
Remove the No. 2 camshaft from the camshaft housing sub-assembly.
11821
29.REMOVE NO. 2 CAMSHAFT BEARING
13801
30.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Remove the 16 No. 1 valve rocker arm sub-assemblies.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
13750
31.REMOVE VALVE LASH ADJUSTER ASSEMBLY
Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
13716
32.REMOVE VALVE STEM CAP
Remove the 16 valve stem caps from the cylinder head sub-assembly.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
11101
33.REMOVE CYLINDER HEAD SUB-ASSEMBLY
Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 cylinder head bolts in the order shown in the illustration. Remove the 10 cylinder head bolts and 10 plate washers.
Arrange the removed parts in such a way that they can be reinstalled to their original locations.
Remove the cylinder head sub-assembly.
Be careful not to drop the plate washers into the cylinder head sub-assembly.
Warpage or cracking of the cylinder head sub-assembly may result from removing the cylinder head bolts in the incorrect order.
11115
34.REMOVE CYLINDER HEAD GASKET
Remove the cylinder head gasket from the cylinder block sub-assembly.