The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.
This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
43457
1.REMOVE DRIVE SHAFT BEARING BRACKET
Remove the 3 bolts and drive shaft bearing bracket.
88370
2.REMOVE COMPRESSOR WITH MOTOR ASSEMBLY
|
Bolt |
|
Nut |
Remove the bolt and 2 nuts.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts and compressor with motor assembly.
16207
3.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Slide the clip and disconnect the No. 2 water by-pass pipe sub-assembly from the outlet water by-pass sub-assembly.
Remove the bolt and the No. 2 water by-pass pipe sub-assembly.
16260
4.REMOVE FLOW SHUTTING VALVE (WATER BY-PASS HOSE ASSEMBLY)
Remove the bolt.
Slide the clip and remove the flow shutting valve (water by-pass hose assembly) from the outlet water by-pass sub-assembly.
Remove the 2 bolts and water hose clamp bracket.
89481B
5.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ Differential Pressure Sensor)
6.REMOVE VACUUM TRANSMITTING HOSE ASSEMBLY (w/ Differential Pressure Sensor)
Slide the clip and remove the vacuum transmitting hose assembly from the No. 1 vacuum transmitting pipe sub-assembly.
25706
7.REMOVE NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Differential Pressure Sensor)
Remove the nut.
Using a 14 mm union nut wrench, remove the No. 1 vacuum transmitting pipe sub-assembly from the exhaust manifold.
17167
8.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
w/o Differential Pressure Sensor, Type A:
Remove the 5 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.
w/o Differential Pressure Sensor, Type B:
Remove the 3 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.
w/ Differential Pressure Sensor:
Remove the 3 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.
17118
9.REMOVE MANIFOLD STAY
17141
10.REMOVE EXHAUST MANIFOLD
w/o Differential Pressure Sensor, Type A:
Using a 12 mm deep socket wrench, remove the 7 nuts and exhaust manifold from the cylinder head sub-assembly.
w/o Differential Pressure Sensor, Type B:
Using a 12 mm deep socket wrench, remove the 7 nuts and exhaust manifold from the cylinder head sub-assembly.
w/ Differential Pressure Sensor:
Using a 12 mm deep socket wrench, remove the 7 nuts and exhaust manifold from the cylinder head sub-assembly.
Remove the exhaust manifold to head gasket from the cylinder head sub-assembly.
22030
11.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY
22271
12.REMOVE THROTTLE BODY GASKET
25680
13.REMOVE EGR COOLER ASSEMBLY
| *1 | No. 3 Water By-pass Hose |
| *2 | Water Hose |
Slide the clip and disconnect the water hose from the EGR cooler assembly.
Slide the clip and disconnect the No. 3 water by-pass hose from the EGR cooler assembly.
Type A:
|
Bolt |
|
Nut |
Remove the 2 bolts, 3 nuts, EGR cooler assembly, EGR cooler gasket and EGR valve gasket.
Type B:
|
Bolt |
|
Nut |
Remove the 3 bolts, 2 nuts, EGR cooler assembly, EGR cooler gasket and EGR valve gasket.
25601
14.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY
15.REMOVE WATER HOSE
Slide the clip and remove the water hose from the EGR valve assembly.
25620
16.REMOVE EGR VALVE ASSEMBLY
Slide the clip and disconnect the No. 8 water by-pass hose from the EGR valve assembly.
Using an 8 mm socket wrench, remove the 2 bolts.
| *a | Pin |
| *b | Hole |
Remove the EGR valve assembly vertically.
16279
17.REMOVE NO. 3 WATER BY-PASS PIPE
Using an 8 mm socket wrench, remove the bolt and disconnect the No. 3 water by-pass pipe from the intake manifold.
Slide the clip and remove the No. 3 water by-pass pipe from the water outlet.
16278
18.REMOVE NO. 2 WATER BY-PASS PIPE
Remove the bolt (A).
Using an 8 mm socket wrench, remove the 2 bolts (B) and No. 2 water by-pass pipe.
17111
19.REMOVE INTAKE MANIFOLD
17177
20.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET
23910A
21.DISCONNECT FUEL TUBE SUB-ASSEMBLY
23801P
22.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY
Using an 8 mm socket wrench, remove the bolt.
Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 1 fuel pipe sub-assembly.
23100X
23.REMOVE FUEL(ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)
16295
24.REMOVE NO. 7 WATER BY-PASS HOSE
Slide the 2 clips and remove the No. 7 water by-pass hose.
82219A
25.REMOVE SENSOR WIRE
Disconnect the 3 connectors.
Disengage the 3 clamps.
Using an 8 mm socket wrench, remove the bolt and sensor wire from the water inlet with thermostat sub-assembly.
82126A
26.REMOVE NO. 6 ENGINE WIRE
Disconnect the 4 connectors.
Disengage the 2 clamps.
Remove the 2 nuts and No. 6 engine wire from the wire harness clamp bracket.
27.REMOVE WIRE HARNESS CLAMP BRACKET
Using an 8 mm socket wrench, remove the 2 bolts and wire harness clamp bracket from the No. 1 ventilation case.
23800
28.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY
23807V
29.REMOVE NO. 1 DELIVERY PIPE SPACER
23291
30.REMOVE INJECTOR VIBRATION INSULATOR
82125N
31.REMOVE NO. 5 ENGINE WIRE
23250F
32.REMOVE PORT FUEL INJECTOR ASSEMBLY
23814B
33.REMOVE FUEL DELIVERY PIPE
23250E
34.REMOVE DIRECT FUEL INJECTOR ASSEMBLY
23255A
35.REMOVE FUEL INJECTOR SEAL
19500
36.REMOVE IGNITION COIL ASSEMBLY
11452
37.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
Remove the engine oil level dipstick.
Using an 8 mm socket wrench, remove the bolt and engine oil level dipstick guide from the camshaft housing sub-assembly.
Remove the O-ring from the engine oil level dipstick guide.
17169A
38.REMOVE NO. 3 EXHAUST MANIFOLD HEAT INSULATOR
Type A:
Remove the bolt and No. 3 exhaust manifold heat insulator from the cylinder block sub-assembly.
Type B:
Remove the 2 bolts and No. 3 exhaust manifold heat insulator from the cylinder block sub-assembly.