Home › Engine / Hybrid System › N04C-VL (ENGINE CONTROL) › ECD SYSTEM
RM2850E _51 Engine / Hybrid System _073159 N04C-VL ENGINE CONTROL _0357053 ECD SYSTEM J

N04C-VL ENGINE CONTROL  ECD SYSTEM  Rough Idling or Excessive Engine Vibrations  


DESCRIPTION

Malfunction Condition Main Trouble Areas Related Trouble Areas
·

Rough idling or shuddering due to abnormal combustion

·

Shuddering when vehicle starting due to clutch system malfunctions


1.

Injector malfunctions

-

Injector assembly sliding malfunction

-

Injector assembly stuck closed

-

Injector assembly stuck open

-

Deposits in injector assembly

-

Injector assembly circuit malfunction


2.

Clutch system malfunctions

-

Clutch system (shuddering when starting)



·

Injector compensation code

·

Fuel leak

·

Engine mounting insulator

·

Intake air system leakage

·

Intake air system blockage

·

Venturi assembly

·

Suction control valve

·

Pressure limiter (common rail assembly)

·

Fuel pressure sensor (common rail assembly)

·

Injector driver (P062D stored simultaneously)

·

Low quality fuel

·

Vehicle modifications

·

Fuel filter air bleed problem

·

Accessory problem (A/C, generator, etc.)

·

ECM



HINT:
·

Rough idling and excessive engine vibrations are checked in this troubleshooting procedure.

·

Specified values in the following troubleshooting flowchart are for reference only. Variations in the Data List result values may occur depending on the measuring conditions or the vehicle's age. Do not judge the vehicle to be normal even when the Data List values indicate a standard level. There are possibly some concealed factors causing the malfunction.

·

Check that the vehicle has not been modified in any way prior to the vehicle inspection.



CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing an injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).

·

After replacing the venturi assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

Before troubleshooting, conduct the following:

1.

Check the fuel quality.

2.

Check the fuel for air.

3.

Check the fuel system for blockages.

4.

Check the air filter.

5.

Check the engine oil.

6.

Check the engine coolant.

7.

Check the engine idling speed and the maximum engine speed.

8.

Check the vacuum pump.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR IN ENGINE COMPARTMENT
a.

Check the wire harness and connector connections of the common rail system components.

HINT:

Check the following components and systems:

·

Sensors

·

Injection or supply pump assembly

·

Common rail assembly

·

Injector assemblies

·

Injector driver

·

Turbocharger system

·

Intake and exhaust systems



OK:

The wire harnesses and connectors are connected securely.



Result:
Proceed to
OK
NG



OK

2.PERFORM CONFIRMATION DRIVING PATTERN

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.PERFORM CONFIRMATION DRIVING PATTERN
HINT:

Drive the vehicle according to the driving pattern below to allow the ECM to store DTCs related to malfunctions of the fuel system and throttle valve. If DTCs are stored, problem areas can be identified.


a.

Start the engine (Procedure "A").


b.

Stop the engine and wait for at least 10 seconds (Procedure "B").


c.

Perform procedure "A" and procedure "B" described above (to allow the ECM to store pressure limiter malfunction DTCs again).



e.

Fully warm up the engine.


f.

Allow the engine to idle for 5 minutes or more.


g.

Drive the vehicle at more than 40 km/h (25 mph) for 1 minute or more (Procedure "C").


h.

Decelerate and stop the vehicle (Procedure "D").


i.

Repeat procedure "C" and procedure "D" 4 times or more.


j.

Stop the engine and wait for at least 10 seconds (Procedure "E").


k.

Repeat procedure "C" and procedure "D" described above (to store DTCs relating to the throttle valve).


l.

Drive the vehicle at more than 70 km/h (43 mph) for at least 1 minute (to store DTCs relating to the injection or supply pump assembly).


Result:
Proceed to
NEXT



NEXT

3.CHECK OUTPUT DTC (RELATED TO ENGINE)
3.CHECK OUTPUT DTC (RELATED TO ENGINE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the pending DTCs.


Result:
Result Proceed to
DTC is not output A
DTCs related to engine B



A

4.PERFORM ACTIVE TEST USING GTS (FUEL LEAK TEST)

B

4.PERFORM ACTIVE TEST USING GTS (FUEL LEAK TEST)
HINT:

By performing this Active Test, the engine speed is maintained at 2000 rpm and the common rail internal fuel pressure is raised to the maximum operating pressure. As a result, a fuel leak check can be conducted while retaining the high common rail pressure.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.


e.

Visually check the injection or supply pump assembly, injector assembly, and fuel line located between the injection or supply pump assembly and common rail assembly for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail assembly and the injector assembly.

HINT:

There may be fuel leaks inside the components, such as the injection or supply pump assembly.


OK:

No fuel leakage.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS

NG

REPAIR OR REPLACE FUEL LEAKAGE PARTS

5.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

Enter the following menus in order and read the values.

·

MAP

·

Fuel Press


Standard:
GTS Display Condition* Standard Range Description
MAP Ignition switch ON (engine stopped) Same as atmospheric pressure Intake manifold internal pressure detected by vacuum sensor
Idling 93 to 100 kPa (698 to 750 mmHg) or less
3000 rpm (no engine load) 110 to 140 kPa (825 to 1050 mmHg) or more
Fuel Press Idling 25000 to 35000 kPa Common rail assembly internal fuel pressure


Result:
Item Result Proceed to
MAP and Fuel press Standard range A
Only MAP Outside standard range B
Only Fuel Press Outside standard range C


HINT:

*: The A/C switch and all accessory switches should be off with a fully-warmed engine.




A

6.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)

B

GO TO DTC P0107 AND P0108 (RELATED TO VACUUM SENSOR)

C

23.INSPECT FUEL PRESSURE SENSOR (COMMON RAIL ASSEMBLY)
6.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
a.

Enter the following menus in order and read the values.

·

Injection Feedback Val #1, #2, #3 and #4

·

Injection Volume


Standard:
GTS Display Condition* Standard Range Description
Injection Feedback Val #1 Idling -7.0 to 7.0 mm3/st Value of injector fuel injection volume compensates for differences in combustion condition of cylinders
·

Positive values indicate control which corrects combustion degradation

·

Negative values indicate control which corrects excessive combustion pressure

·

If problems exist, "Injection Feedback Val" may deviate from -7.0 and 7.0 mm3/st


Injection Feedback Val #2 Idling -7.0 to 7.0 mm3/st
Injection Feedback Val #3 Idling -7.0 to 7.0 mm3/st
Injection Feedback Val #4 Idling -7.0 to 7.0 mm3/st
Injection Volume Idling 5.0 to 15.0 mm3/st Fuel injection volume value controlled by ECU
·

Controls NE signal, fuel temperature, engine coolant temperature, intake air temperature, manifold absolute pressure and atmospheric pressure

·

If problems exist, "Injection Volume" may be outside the standard range




Result:
Result Proceed to
Standard range A
Injection Feedback Val #1 to #4 and/or Injection Volume outside standard range B


HINT:

*: The A/C switch and all accessory switches should be off with a fully-warmed engine.




A

7.CHECK INJECTOR COMPENSATION CODE

B

13.IDENTIFY MALFUNCTIONING CYLINDER INJECTOR
7.CHECK INJECTOR COMPENSATION CODE
a.

Read the injector compensation code (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).

HINT:

If the injector compensation code is not correctly registered, it may cause malfunctions (Click hereEngine / Hybrid System>N04C-VL (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



b.

Check the injector compensation code.

OK:

Compensation code of the installed injector assembly is the same as the code registered in the ECM.



Result:
Proceed to
OK
NG



OK

8.RESET ECM

NG

PERFORM REGISTRATION INJECTOR COMPENSATION CODE

8.RESET ECM
a.

Disconnect the cable from the negative (-) battery terminal for at least 2 minutes.


b.

Reconnect the cable to the negative (-) battery terminal.


c.

Check whether the malfunction has been successfully repaired by performing a driving test using the freeze frame data recorded at the time the malfunction occurred.

OK:

Malfunction has been repaired successfully.



Result:
Result Proceed to
NG A
OK B



A

9.CHECK ENGINE MOUNTING INSULATOR

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

9.CHECK ENGINE MOUNTING INSULATOR
a.

Visually check that the engine mounting insulator is installed correctly and is not crooked or twisted.

OK:

No abnormalities.



Result:
Proceed to
OK
NG



OK

10.CHECK INTAKE SYSTEM

NG

REPAIR OR REPLACE ENGINE MOUNTING INSULATOR

10.CHECK INTAKE SYSTEM
a.

Check for air leaks and blockage between the air cleaner and turbocharger sub-assembly.


b.

Check for air leaks and blockage between the turbocharger sub-assembly and intake manifold.

OK:

No air leaks or blockage.



Result:
Proceed to
OK
NG



OK

11.INSPECT EXHAUST RETARDER ASSEMBLY

NG

REPAIR OR REPLACE INTAKE SYSTEM

11.INSPECT EXHAUST RETARDER ASSEMBLY
a.

Inspect the exhaust retarder assembly.


Result:
Proceed to
OK
NG



OK

12.INSPECT VENTURI ASSEMBLY

NG

REPLACE EXHAUST RETARDER ASSEMBLY

12.INSPECT VENTURI ASSEMBLY
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Actual Throttle Position.


e.

Read the value.

Standard:
Ignition switch ON:

0%

Idling (Warmed up engine):

81 to 95%

Accelerator pedal fully depressed:

0%



Result:
Result Proceed to
NG A
OK B



A

B

15.PERFORM ACTIVE TEST USING GTS (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)
13.IDENTIFY MALFUNCTIONING CYLINDER INJECTOR
a.

Follow the instructions in the table below according to the check result of the GTS.

HINT:

This operation is based on the premise that the common rail assembly pressure is normal.


Standard:
GTS Display Condition* Reference Value
Injection Feedback Val #1 to #4 Idling -7.0 to 7.0 mm3/st
Injection Volume Idling 5.0 to 15.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up.


Result:
Injection Feedback Val #1 to #4 Injection volume
Less than 5.0 mm3 Between 5.0 and 23.0 mm3/st (Normal) More than 23.0 mm3/st
7.0 mm3/st or more, -7.0 mm3/st or less A B B
Between -7.0 and 7.0 mm3/st - Normal C*

Proceed to Inspection Areas Descriptions
A Inspect and repair cylinder injector assembly with revised injection volume of less than -7.0 mm3/st:
·

Perform power balance inspection and identify malfunctioning cylinder

·

Replace malfunctioning cylinder injector assembly


Abnormal cylinder injector assembly injects excessively large quantity of fuel
B Identify malfunctioning cylinders by conducting power balance inspection:
·

Perform power balance inspection to identify malfunctioning cylinders

·

Clean malfunctioning cylinder injector assembly and check it


·

Fuel injection volume too low due to injector assembly nozzle being blocked by deposits

·

Abnormal cylinder compression decreases

·

Abnormal cylinder injector assembly injects excessively large quantity of fuel


C Inspect and repair all cylinder injector assemblies:
Clean all cylinder injector assemblies and check them
All cylinder injector assemblies inject excessively small quantity of fuel:
Fuel injection volume too low due to all cylinder injector assembly nozzles being blocked by deposits


HINT:

*: When the Injection Volume displayed on the GTS is large despite the Fuel Press and Injection Feedback Val #1 to #4 in the Data List being normal, the injector assembly may be clogged. In this case, there may be deposits inside or outside the tip of the injector assembly.

·

Despite the injector assembly functioning normally, the indicated Injection Feedback Val #1 to #4 value may be outside the normal operating range due to compensation for other problems (such as low compression).

·

Injection Feedback Val #1 to #4 is the value used to correct the fuel injection volumes of each cylinder, in order to optimize (compensate for the unevenness between) all the cylinder combustion conditions. If any of the cylinder malfunction, the fuel injection volumes for the normal cylinders are corrected simultaneously. As a result, the Injection Feedback Val #1 to #4 may deviate from the standard range.





A

14.PERFORM ACTIVE TEST USING GTS (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)

B

15.PERFORM ACTIVE TEST USING GTS (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)

C

20.CHECK INJECTOR ASSEMBLY FOR DEPOSITS
14.PERFORM ACTIVE TEST USING GTS (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder #1, #2, #3 and #4 Fuel Cut.


e.

Check the four cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.

HINT:
·

If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change of idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

15.PERFORM ACTIVE TEST USING GTS (INJECTOR CUT FOR IDENTIFYING MALFUNCTIONING CYLINDER)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Select Cylinder #1, #2, #3 and #4 Fuel Cut.


e.

Check the four cylinders in sequence to identify any faulty cylinders by performing the power-balance inspection.

HINT:
·

If the engine idle does not change when an injector is disabled, the cylinder being tested is malfunctioning.

·

If the cylinder being tested is normal, there will be a significant change of idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

16.CHECK CYLINDER COMPRESSION PRESSURE
16.CHECK CYLINDER COMPRESSION PRESSURE
a.

Check the cylinder compression pressure (Click hereEngine / Hybrid System>N04C-VL (ENGINE MECHANICAL)>ENGINE>ON-VEHICLE INSPECTION).


Result:
Proceed to
OK
NG



OK

17.CHECK MALFUNCTIONING CYLINDER'S INJECTOR ASSEMBLY FOR DEPOSITS

NG

CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION

17.CHECK MALFUNCTIONING CYLINDER'S INJECTOR ASSEMBLY FOR DEPOSITS
HINT:

If an injector assembly is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.


a.

Check the injector assembly for any deposits.

Result:
Injector Condition Proceed to
Deposits A
No deposits B




A

18.CLEAN INJECTOR ASSEMBLY

B

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

18.CLEAN INJECTOR ASSEMBLY
a.

Wipe away deposits from the tips of the injector assemblies.

HINT:
·

Solvent or carbon removal agents help remove deposits easily.

·

Exercise extreme care not to damage the injector assemblies while wiping off the deposits.




Result:
Proceed to
NEXT



NEXT

19.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
19.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
a.

Reinstall the injector assembly.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine and warm it up.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.


g.

Enter the following menus in order and read the values.

·

Injection Feedback Val #1, #2, #3 and #4

·

Injection Volume


Standard:
GTS Display Condition* Reference Value
Injection Feedback Val #1 to #4 Idling -7.0 to 7.0 mm3/st
Injection Volume Idling 5.0 to 15.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up. When the values are outside the standard range, deposits inside the injector assembly may be causing the problem.


OK:

Values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER

20.CHECK INJECTOR ASSEMBLY FOR DEPOSITS
HINT:

If an injector assembly is contaminated with deposits, the fuel injection volume deviates from the standard range. This may cause malfunctions.


a.

Check the injector assembly for any deposits.


Result:
Injector Condition Proceed to
Deposits A
No deposits B



A

21.CLEAN INJECTOR ASSEMBLY

B

21.CLEAN INJECTOR ASSEMBLY
a.

Wipe away deposits from the tips of the injector assemblies.

HINT:
·

Solvent or carbon removal agents help remove deposits easily.

·

Exercise extreme care not to damage the injector assemblies while wiping off the deposits.




Result:
Proceed to
NEXT



NEXT

22.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
22.READ VALUE USING GTS (INJECTION FEEDBACK VAL AND INJECTION VOLUME)
a.

Reinstall the injector assembly.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine and warm it up.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine and ECT / Data List.


h.

Enter the following menus in order and read the values.

·

Injection Feedback Val #1, #2, #3 and #4

·

Injection Volume


Standard:
GTS Display Condition* Reference Value
Injection Feedback Val #1 to #4 Idling -7.0 to 7.0 mm3/st
Injection Volume Idling 5.0 to 15.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, and the engine should be fully warmed up. When the values are outside the standard range, deposits inside the injector assembly may be causing the problem.


OK:

Values are within the standard range.



Result:
Proceed to
OK
NG



OK

END

NG

23.INSPECT FUEL PRESSURE SENSOR (COMMON RAIL ASSEMBLY)
a.

Inspect the fuel pressure sensor (common rail assembly) (Click hereEngine / Hybrid System>N04C-VL (FUEL)>COMMON RAIL>INSPECTION).


Result:
Proceed to
OK
NG



OK

24.INSPECT SUCTION CONTROL VALVE

NG

REPLACE FUEL PRESSURE SENSOR (COMMON RAIL ASSEMBLY)

24.INSPECT SUCTION CONTROL VALVE
a.

Inspect the suction control valve (Click hereEngine / Hybrid System>N04C-VL (FUEL)>FUEL SUPPLY PUMP>INSPECTION).


Result:
Proceed to
OK
NG



OK

CHECK AND REPLACE PRESSURE LIMITER (COMMON RAIL ASSEMBLY)

NG