Home › Engine / Hybrid System › N04C-VQ (ENGINE CONTROL) › ECD SYSTEM › from 2019.08
RM2850E _51 Engine / Hybrid System _073138 N04C-VQ ENGINE CONTROL _0355854 ECD SYSTEM C

N04C-VQ ENGINE CONTROL  ECD SYSTEM  P0093  Fuel System Leak Detected - Large Leak  


DESCRIPTION

Refer to DTC P0087 (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0087).

Refer to DTC P0088 (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>P0088).

DTC No. DTC Detection Condition Trouble Area
P0093 DTC is output when following conditions (a), (b) and (c) are all met and if difference of common rail pressure that fuel pressure sensor detects before and after fuel injection varies greatly from difference of value that ECM calculates before and after fuel injection, ECM determines that there may be fuel leaks (1 trip detection logic).

(a) Engine speed is 1500 rpm or higher.

(b) Fuel pressure sensor is normal (P0190, P0192, and P0193 are not detected).

(c) Suction control valve is normal (P0088, P0627 and P1229 are not detected).


·

Fuel leak (injection or supply pump assembly to common rail assembly to injector assembly)

·

Injector assembly

·

Injection or supply pump assembly

(suction control valve)

·

Wire harness or connector

·

Common rail assembly

·

ECM



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injection or supply pump assembly, the ECM needs initialization (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).

·

After replacing the injector assembly, the ECM needs registration (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION).



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, as well as other data recorded at the time of a malfunction.


PROCEDURE

1.CHECK OTHER DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs.


Result:
Result Proceed to
DTC P0087, P0088, P0190, P0191, P0192, P0193, P0201, P0202, P0203, P0204, P0627, P062D or P1229 is not output A
DTC P0087, P0088, P0190, P0191, P0192, P0193, P0201, P0202, P0203, P0204, P0627, P062Dor P1229 is output B



A

2.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)

B

2.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
HINT:

By performing this Active Test, the engine speed is maintained at 2000 rpm and the common rail assembly internal fuel pressure is raised to the maximum operating pressure. As a result, a fuel leak check can be conducted while retaining the high common rail pressure.


a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Test the Fuel Leak.


e.

Visually check the injection or supply pump assembly, injector assembly and fuel line located between the injection or supply pump assembly and common rail assembly for fuel leaks and fuel pressure leaks. Also, perform the same check on the fuel line between the common rail assembly and the injector assembly.

HINT:

There may be fuel leaks inside the components, such as the injection or supply pump assembly.


OK:

No leakage.



Result:
Proceed to
OK
NG



OK

3.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

NG

REPAIR OR REPLACE FUEL LEAKAGE POINT

3.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Inspect the Injection or supply pump assembly (suction control valve) (Click hereEngine / Hybrid System>N04C-VQ (FUEL)>FUEL SUPPLY PUMP>INSPECTION).


Result:
Proceed to
OK
NG



OK

4.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)

NG

11.INSPECT FUEL INJECTION SYSTEM
4.INSPECT INJECTION OR SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE)
a.

Disconnect the suction control valve connector and then start the engine.

OK:

Engine does not start.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (TARGET PUMP SCV CURRENT)

NG

11.INSPECT FUEL INJECTION SYSTEM
5.READ VALUE USING GTS (TARGET PUMP SCV CURRENT)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Target Pump SCV Current.


e.

Read the value.

Standard:
Engine Speed Result
Idling 1350 to 2200 mA



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (FUEL PRESSURE)

NG

11.INSPECT FUEL INJECTION SYSTEM
6.READ VALUE USING GTS (FUEL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press and Target Common Rail Pressure.


e.

Read the value.

Standard:
GTS Display Condition Specified Condition
Fuel Press Idling 20000 to 30000 kPa
3000 rpm without Load 130000 to 150000 kPa
Target Common Rail Pressure Idling Deviation from Fuel Press within 5000 kPa
3000 rpm without Load Deviation from Fuel Press within 5000 kPa



Result:
Result Proceed to
NG A
OK B



A

7.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)

B

12.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
7.CHECK HARNESS AND CONNECTOR (FUEL PRESSURE SENSOR - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the fuel pressure sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B105-16 (PCR1) - B93-2 (PCR1) Always Below 1 Ω
B104-13 (VC) - B93-1 (VC1) Always Below 1 Ω
B104-14 (E2) - B93-3 (E1) Always Below 1 Ω
B105-2 (PCR2) - B93-5 (PCR2) Always Below 1 Ω
B105-13 (VC2) - B93-6 (VC2) Always Below 1 Ω
B105-14 (E21) - B93-4 (E2) Always Below 1 Ω
B105-16 (PCR1) or B93-2 (PCR1) - Body ground Always 10 kΩ or higher
B104-13 (VC) or B93-1 (VC1) - Body ground Always 10 kΩ or higher
B105-2 (PCR2) or B93-5 (PCR2) - Body ground Always 10 kΩ or higher
B105-13 (VC2) or B93-6 (VC2) - Body ground Always 10 kΩ or higher
B104-14 (E2) or B93-3 (E1) - Other terminals Always 10 kΩ or higher
B105-14 (E21) or B93-4 (E2) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.READ VALUE USING GTS (FUEL PRESSURE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL PRESSURE SENSOR - ECM)

8.READ VALUE USING GTS (FUEL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Fuel Press.


e.

Wiggle the fuel pressure sensor connector and check that the fuel pressure reading does not change.

OK:

The fuel pressure reading does not change.



Result:
Proceed to
OK
NG



OK

9.PERFORM INITIALIZATION (INJECTION OR SUPPLY PUMP ASSEMBLY)

NG

REPLACE COMMON RAIL ASSEMBLY

9.PERFORM INITIALIZATION (INJECTION OR SUPPLY PUMP ASSEMBLY)

Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0093)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Warm up the engine.


f.

Drive the vehicle by 1500 rpm or more for 5 minutes.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


h.

Read the DTC.


Result:
Result Proceed to
DTC is not output A
DTC P0093 is output B



A

END

B

11.INSPECT FUEL INJECTION SYSTEM
11.INSPECT FUEL INJECTION SYSTEM
a.

Inspect the fuel injection system circuit (Click hereEngine / Hybrid System>N04C-VQ (ENGINE CONTROL)>ECD SYSTEM>Fuel Injection System).


b.

Check whether the malfunction has been repairedsuccessfully.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG

12.CHECK HARNESS AND CONNECTOR (SUCTION CONTROL VALVE - ECM)
a.

Disconnect the suction control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B103-23 (PCV+) - B52-1 (SCV+) Always Below 1 Ω
B103-12 (PCV-) - B52-2 (SCV-) Always Below 1 Ω
B103-23 (PCV+) or B52-1 (SCV+) - Body ground Always 10 kΩ or higher
B103-12 (PCV-) or B52-2 (SCV-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT ECM (PCR VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SUCTION CONTROL VALVE - ECM)

13.INSPECT ECM (PCR VOLTAGE)
a.

Start the engine.


A260250E30
1.302,0.104 1.792,0.396 0.49,0.292 1.844,0.104 2.333,0.396 0.49,0.292 2.188,0.865 2.917,1.729 true 1.688,0.875 2.271,1.76 true 1.521,0.875 0.49,1.75 true 1.688,0.719 1.302,1.74 true 1.396,0.167 1.813,0.323 0.417,0.156 10 false B105 1.938,0.167 2.417,0.323 0.479,0.156 10 false B104 0.063,0.073 0.25,0.281 0.188,0.208 10 false *a 1.042,1.76 1.677,2.031 0.635,0.271 10 false 2 (PCR2) 0.292,1.76 0.99,2 0.698,0.24 10 false 16 (PCR1) 2.729,1.771 3.427,2.01 0.698,0.24 10 false 14 (E2) 2.125,1.771 2.76,2.042 0.635,0.271 10 false 14 (E21)

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B105-16 (PCR1) - B104-14 (E2) Idling 1.7 to 2.2 V
B105-2 (PCR2) - B105-14 (E21) Idling 1.2 to 1.6 V


Text in Illustration
*a Component with harness connected
(ECM)


Result:
Proceed to
OK
NG



OK

NG

REPLACE COMMON RAIL ASSEMBLY