16400
1.REMOVE RADIATOR ASSEMBLY
33110
2.REMOVE MANUAL TRANSMISSION ASSEMBLY
31250
3.REMOVE CLUTCH DISC ASSEMBLY
17341F
4.REMOVE NO. 1 AIR HOSE
Separate the engine wire.
Disconnect the ventilation hose.
Remove the bolt.
Loosen the 2 No. 1 air cleaner hose clamps and remove the No. 1 air hose.
17201
5.REMOVE TURBOCHARGER SUB-ASSEMBLY
16577C
6.REMOVE RADIATOR PIPE
Remove the 2 bolts and radiator pipe.
88320
7.SEPARATE COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
Disconnect the connector.
Remove the 6 bolts and separate the cooler compressor assembly.
27020
8.REMOVE GENERATOR ASSEMBLY
44360
9.SEPARATE VANE PUMP OIL RESERVOIR ASSEMBLY
Remove the 3 bolts and vane pump oil reservoir assembly.
53712C
10.REMOVE FRONT FENDER APRON LH
44310
11.SEPARATE VANE PUMP ASSEMBLY
Remove the 2 bolts and separate the vane pump assembly.
Remove the O-ring.
17342P
12.REMOVE NO. 2 AIR HOSE
44774
13.DISCONNECT UNION TO CONNECTOR TUBE HOSE
Disconnect the union to connector tube hose.
23273C
14.DISCONNECT NO.2 FUEL HOSE
Disconnect the No. 2 fuel hose.
22100A
15.DISCONNECT INJECTION PUMP TO FUEL FILTER FUEL HOSE OR PIPE
Disconnect the injection pump to fuel filter fuel hose or pipe.
28100
16.REMOVE STARTER ASSEMBLY
45470
17.SEPARATE TIE ROD ASSEMBLY LH
Remove the cotter pin.
Remove the nut.
Using SST, separate the tie rod end assembly LH from the steering relay rod assembly.
45450
18.SEPARATE STEERING RELAY ROD ASSEMBLY
| *a | for Idler Arm Bracket Assembly Side |
| *b | for Center Arm Bracket Assembly Side |
Remove the 2 cotter pins.
Remove the 2 nuts.
Using SST, separate the steering relay rod assembly from the center arm.
51202D
19.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
Remove the 6 bolts, 4 nuts, 4 washers and front lower suspension crossmember sub-assembly.
While fixing the nut in place, loosen and remove the through bolt.
82121
20.SEPARATE ENGINE WIRE
Separate all engine wires from the engine.
21.REMOVE ENGINE ASSEMBLY
Support the engine using an engine lifter.
Remove the 2 nuts.
Remove the 4 bolts and front No. 1 engine mounting bracket LH.
Remove the engine mounting stabilizer and front engine mounting insulator.
Remove the 2 nuts.
Remove the 4 bolts and front No. 1 engine mounting bracket RH.
Remove the engine mounting stabilizer and front engine mounting insulator.
Remove the engine assembly.
12180E
22.REMOVE OIL FILLER CAP SUB-ASSEMBLY
Remove the oil filler cap sub-assembly.
11201
23.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the 2 bolts, 2 cylinder head cover stay and cylinder head cover sub-assembly.
25625B
24.REMOVE EGR VALVE BRACKET
Remove the 4 bolts and EGR valve bracket.
15301
25.REMOVE OIL DIPSTICK GUIDE
Remove the bolt and oil dipstick guide.
Remove the O-ring from the oil dipstick guide.
16206C
26.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
Disconnect the 2 water by-pass hoses from the EGR valve assembly.
Remove the 3 bolts and 2 union bolts, then remove the water by-pass pipe sub-assembly.
17113D
27.REMOVE NO. 1 INTAKE PIPE
11202D
28.REMOVE NO. 2 CYLINDER HEAD COVER SUB-ASSEMBLY
Remove the wire harness.
Remove the 2 cylinder head cover cushion rubber.
Remove the 2 bolts and No. 2 cylinder head cover sub-assembly.
Remove the 4 No. 2 cylinder head cover gaskets.
17113
29.REMOVE NO. 2 INTAKE PIPE
Remove the 4 bolts and No. 2 intake pipe.
23741B
30.REMOVE INJECTION PIPE CLAMP
23670
31.REMOVE INJECTOR ASSEMBLY
17111
32.REMOVE INTAKE MANIFOLD
17141
33.REMOVE EXHAUST MANIFOLD
83530
34.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY
35.REMOVE OIL COOLER COVER SUB-ASSEMBLY
89422
36.REMOVE ENGINE COOLANT TEMPERATURE SENSOR
Using a 19 mm deep socket wrench, remove the water temperature sender gauge assembly.
37.REMOVE CRANKSHAFT POSITION SENSOR
Remove the bolt and crankshaft position sensor.
38.REMOVE CAMSHAFT POSITION SENSOR
Remove the bolt and camshaft position sensor.
16630G
39.REMOVE IDLER PULLEY ASSEMBLY
Remove the 2 bolts and idler pulley assembly.
88440B
40.REMOVE IDLE PULLEY ASSEMBLY WITH BRACKET (w/ Air Conditioning System)
Remove the 3 bolts and idle pulley assembly with bracket.
88431
41.REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
Remove the 7 bolts, compressor mounting bracket set and No. 1 compressor mounting bracket.
| *1 | Compressor Mounting Bracket Set |
| *2 | No. 1 Compressor Mounting Bracket |
16331
42.REMOVE WATER OUTLET SUB-ASSEMBLY
Remove the 3 bolts and water outlet sub-assembly.
16331A
43.REMOVE THERMOSTAT
16331
44.REMOVE WATER OUTLET HOUSING
Remove the 3 bolts, water outlet housing and gasket.
87208L
45.REMOVE WATER PIPE SUB-ASSEMBLY
Remove the 3 bolts, water pipe sub-assembly and O-ring.
16206
46.REMOVE NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
Disconnect the water hose.
Remove the 2 bolts and No. 2 water by-pass pipe sub-assembly.
16206C
47.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
Remove the 6 bolts, 6 O-rings and water by-pass pipe sub-assembly.
16100
48.REMOVE ENGINE WATER PUMP ASSEMBLY
23803H
49.REMOVE FUEL RETURN PIPE SUB-ASSEMBLY
23811
50.REMOVE FUEL FILTER TO INJECTION PUMP FUEL PIPE
19971E
51.REMOVE VACUUM PIPE
Remove the nut and pipe clamp.
Remove the union bolt, vacuum pipe and 2 gaskets.
29601B
52.REMOVE VACUUM PUMP OIL PIPE SUB-ASSEMBLY
29300
53.REMOVE VACUUM PUMP ASSEMBLY
54.REMOVE NO. 3 NOZZLE LEAKAGE PIPE SUB-ASSEMBLY
Loosen the hose clamp, 2 union bolts, 2 gaskets and the No. 3 nozzle leakage pipe sub-assembly.
23810A
55.REMOVE COMMON RAIL ASSEMBLY
Remove the 2 bolts and common rail assembly.
82702E
56.REMOVE WIRING HARNESS BRACKET
Remove the 2 bolts and wiring harness bracket.
23849G
57.REMOVE FUEL SUPPORT
Remove the 2 bolts and fuel support.
Remove the 2 bolts and fuel support.
22100
58.REMOVE INJECTION OR SUPPLY PUMP ASSEMBLY
Remove the 4 bolts and injection or supply pump assembly.