Check whether the engine is TMC made or not by referring to the following illustration.
| *A | for TMC Made Engine | *B | except TMC Made Engine |
| *1 | Engine Oil Level Dipstick Guide | *2 | Water Inlet Housing |
| *3 | Water Inlet Housing Drain Cock Assembly | - | - |
13211
1.INSTALL PISTON
Using a screwdriver, install a new snap ring at one end of the piston pin hole.
Make sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.
Gradually heat the piston up to 80 to 90°C (176 to 194°F).
for 2-piece Type:
Align the front marks of the piston and connecting rod, then push in the piston pin with your thumb until the pin comes into contact with the snap ring.
Make sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.
| *A | for TMC Made Engine |
| *B | except TMC Made Engine |
| *a | Front Mark |
for 3-piece Type:
Align the front marks on the piston and connecting rod, and push in the piston with a thumb.
Make sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.
| *A | for TMC Made Engine |
| *B | except TMC Made Engine |
| *a | Front Mark |
Using a screwdriver, install a new snap ring on the other end of the piston pin hole.
13011
2.INSTALL PISTON RING SET
for 2-piece Type:
Install the expander and oil ring by hand.
Install the expander and oil ring so that their ring ends are at opposite sides.
Securely install the expander to the oil ring's inner groove.
| *1 | Oil Ring |
| *2 | Oil Ring (Expander) |
for 3-piece Type:
Install the oil ring expander and 2 side rails by hand.
When installing the upper side rail and lower side rail, the ends of the oil ring expander may overlap. If it occurs, the upper side rail or lower side rail may move out of its groove.
| *1 | Upper Side Rail |
| *2 | Oil Ring Expander |
| *3 | Lower Side Rail |
Check that the ends of the oil ring expander are not overlapping and that the upper side rail and lower side rail are securely installed into the groove.
After installing the oil ring expander, upper side rail and lower side rail, press around the circumference with a finger to check that they are securely installed into the groove.
If the oil ring expander is not securely installed into the groove, check that the ends of the oil ring expander are not overlapping.
If the ends of the oil ring expander are overlapping, remove the upper side rail and lower side rail and realign the oil ring expander using a screwdriver.
| *a | Press around the circumference | *b | Paint (Purple or White) |
| *c | Ring End | *d | Correct |
| *e | Incorrect (Ends of the oil ring expander are overlapping) | - | - |
Using a piston ring expander, install the 2 compression rings with the paint marks as shown in the illustration.
Install the No. 2 compression ring with the code mark (2N) facing upward.
for 2-piece Type:
Position the piston rings so that the ring ends are as shown in the illustration.
| *A | for TMC Made Engine |
| *B | except TMC Made Engine |
| *1 | No. 1 Compression Ring and Oil Ring Rail |
| *2 | No. 2 Compression Ring and Oil Ring Expander |
| *a | Front Mark |
for 3-piece Type:
Position the piston rings so that the ring ends are as shown in the illustration.
| *A | for TMC Made Engine |
| *B | except TMC Made Engine |
| *1 | Lower Side Rail |
| *2 | No. 2 Compression Ring |
| *3 | Upper Side Rail |
| *4 | No. 1 Compression Ring and Oil Ring Expander |
| *a | Front Mark |
15708
3.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY
Install the 4 No. 1 oil nozzle sub-assemblies with the 4 bolts.
11711
4.INSTALL CRANKSHAFT BEARING
Install the crankshaft bearing onto the cylinder block.
Do not apply engine oil to the crankshaft bearing or its contact surface.
11721
5.INSTALL NO. 2 CRANKSHAFT BEARING
Install the No. 2 crankshaft bearing onto the bearing cap.
Do not apply engine oil to the No. 2 crankshaft bearing or its contact surface.
11791
6.INSTALL UPPER CRANKSHAFT THRUST WASHER
Install the 2 upper crankshaft thrust washers onto the No. 3 journal position of the cylinder block with the oil grooves facing outward.
13411
7.INSTALL CRANKSHAFT
Apply engine oil to the upper bearing, and install the crankshaft onto the cylinder block.
Examine the front marks and numbers, and install the bearing caps onto the cylinder block in the order shown in the illustration.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
Using several steps, uniformly install and tighten the 10 bearing cap bolts in the sequence shown in the illustration.
Mark the front of the bearing cap bolts with paint.
Further tighten the 10 bearing cap bolts by 90° in the same sequence.
Check that the paint marks are now at a 90° angle to the front.
Check that the crankshaft turns smoothly.
13041
8.INSTALL CONNECTING ROD BEARING
Align the connecting rod bearing claw with the oil groove of the connecting rod or connecting rod cap.
Do not apply engine oil to the contact surfaces of the connecting rod cap and connecting rod bearing.
Do not apply engine oil to the contact surfaces of the connecting rod and connecting rod bearing.
13211
9.INSTALL PISTON WITH CONNECTING ROD
Apply engine oil to the cylinder walls, pistons, and surfaces of the connecting rod bearings.
for 2-piece Type:
Check the position of the piston ring ends.
| *A | for TMC Made Engine |
| *B | except TMC Made Engine |
| *1 | No. 1 Compression Ring and Oil Ring Rail |
| *2 | No. 2 Compression Ring and Oil Ring Expander |
| *a | Front Mark |
for 3-piece Type:
Check the position of the piston ring ends.
| *A | for TMC Made Engine |
| *B | except TMC Made Engine |
| *1 | Lower Side Rail |
| *2 | No. 2 Compression Ring |
| *3 | Upper Side Rail |
| *4 | No. 1 Compression Ring and Oil Ring Expander |
| *a | Front Mark |
Confirm that the ends of the oil ring expander are not overlapping and that the upper side rail and lower side rail are securely installed into the groove.
After installing the oil ring expander, upper side rail and lower side rail, press around the circumference with a finger to check that they are securely installed into the groove.
If the oil ring expander is not securely installed into the groove, check that the ends of the oil ring expander are not overlapping.
If the ends of the oil ring expander are overlapping, remove the upper side rail and lower side rail and realign the oil ring expander using a screwdriver.
| *a | Press around the circumference | *b | Paint (Purple or White) |
| *c | Ring End | *d | Correct |
| *e | Incorrect (Ends of the oil ring expander are overlapping) | - | - |
for 2-piece Type:
Using a hammer handle and piston ring compressor, press a piston and connecting rod into each cylinder with the front mark of the piston facing forward.
| *A | for TMC Made Engine |
| *B | except TMC Made Engine |
| *a | Front Mark |
|
Front |
for 3-piece Type:
Using a hammer handle and piston ring compressor, press a piston and connecting rod into each cylinder with the front mark of the piston facing forward.
| *A | for TMC Made Engine |
| *B | except TMC Made Engine |
| *a | Front Mark |
|
Front |
Check that the front mark of the connecting rod cap is facing in the correct direction.
Match the numbered connecting rod cap with the connecting rod.
Apply a light coat of engine oil to the threads and under the heads of the connecting rod bolts.
Using a 12 mm socket wrench, tighten the bolts in several passes to the specified torque.
Mark the front of the connecting rod bolts with paint.
Further tighten the connecting rod bolts by 90° as shown in the illustration.
Check that the paint marks are now at a 90° angle to the front.
Check that the crankshaft turns smoothly.
11420
10.INSTALL STIFFENING CRANKCASE ASSEMBLY
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block and stiffening crankcase assembly.
Place a new O-ring on the cylinder block as shown in the illustration.
Temporarily tighten the pulley set bolt.
Turn the crankshaft so that the key groove is facing downward.
Apply seal packing in a continuous bead (diameter: 2.5 to 3.0 mm (0.098 to 0.118 in.)) to the places shown in the illustration.
Toyota Genuine Seal Packing Black, Three bond 1207B or Equivalent
Remove any oil from the contact surface.
Ensure that no oil packing enters the oil path. The oil path has a groove to catch excess seal packing. Do not apply seal packing to the oil path side of the groove or to the groove itself, or seal packing may enter the oil path.
Install the stiffening crankcase assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.
Do not add engine oil for at least 2 hours after the installation.
Install the stiffening crankcase assembly to the cylinder block.
Temporarily install the stiffening crankcase assembly with the 11 bolts.
| Item | Bolt Length |
|---|---|
| Bolt A | 122 mm (4.80 in.) |
| Bolt B | 45 mm (1.77 in.) |
Using several steps, uniformly tighten the 11 bolts in the sequence shown in the illustration.
Wipe off the excess seal packing with a clean piece of cloth.
11.INSTALL NO. 1 BALANCESHAFT BEARING
Clean each No. 1 balanceshaft bearing installation surface and inner and outer surfaces of the No. 1 balanceshaft bearing.
Do not apply engine oil to the No. 1 balanceshaft bearing installation surface or the outer surface of the No. 1 balanceshaft bearing.
Align the claw of the No. 1 balanceshaft bearing with the groove of the balanceshaft housing and install the 8 No. 1 balanceshaft bearings.
Apply engine oil to the inner surface of the No. 1 balanceshaft bearing.
12.INSTALL NO. 1 AND NO. 2 BALANCESHAFT
Turn the No. 1 driven gear counterclockwise until it stops, then align the matchmark of the No. 1 driven gear with that of the No. 2 driven gear.
Install the No. 1 balanceshaft with the timing mark positioned as shown in the illustration. [*1]
(A) is not a timing mark.
Install the No. 2 balanceshaft with the timing mark positioned as shown in the illustration.
Make sure that the key groove of the crankshaft and timing mark of the balanceshafts are positioned as shown in the illustration.
(A) is not a timing mark.
Apply a light coat of engine oil under the heads of the balanceshaft housing bolts.
Install the balanceshaft housing bolts.
The balanceshaft housing bolts are tightened in 2 progressive steps.
Step 1:
Install and uniformly tighten the 8 bolts in the order shown in the illustration.
Step 2:
Mark the front side of each balanceshaft housing bolt head with paint.
Tighten the balanceshaft housing bolts 90° in the same order.
Check that the paint marks are now at a 90° angle to the front.
Turn the crankshaft 360° and check that the timing marks of the balanceshafts are positioned as shown in the illustration with the key groove of the crankshaft facing downward.
If the timing marks are not positioned as shown in the illustration, perform the procedure from step [*1] again.
(A) is not a timing mark.
Remove the pulley set bolt.
11401L
13.INSTALL REAR CRANKSHAFT OIL SEAL
Apply multi-purpose grease to the lip of a new rear crankshaft oil seal.
Keep the lip free of foreign objects.
Using SST and a hammer, tap in the new rear crankshaft oil seal until its surface is flush with the rear crankshaft oil seal retainer edge.
Wipe any extra grease off of the crankshaft.
Do not tap the rear crankshaft oil seal at an angle.
15678B
14.INSTALL OIL CONTROL VALVE FILTER
Check that there are no foreign objects on the mesh part of the oil control valve filter.
Using a 6 mm socket hexagon wrench, install a new gasket and the oil control valve filter with the plug.
16323
15.INSTALL WATER INLET HOUSING (except TMC Made Engine)
Install a new water inlet housing O-ring and water inlet housing gasket to the water inlet housing.
Install the water inlet housing to the cylinder block with the 5 bolts in the order shown in the illustration.
Using an E5 "TORX" socket, install the stud bolts as shown the illustration.
11415
16.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY (for TMC Made Engine without Engine Oil Cooler)
Apply adhesive to 2 or 3 threads of the cylinder block water drain cock sub-assembly.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the drain cock as shown in the illustration.
Install the cylinder block water drain cock sub-assembly within 3 minutes.
Do not add coolant for 1 hour after installation.
Be sure to only tighten the cylinder block water drain cock sub-assembly up to 360 degrees to position the pipe. Do not loosen the cylinder block water drain cock sub-assembly to position the pipe.
Make sure to position the pipe within the range shown in the illustration.
16323D
17.INSTALL WATER INLET HOUSING DRAIN COCK ASSEMBLY (except TMC Made Engine)
Apply adhesive to 2 or 3 threads of the water inlet housing drain cock assembly.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the water inlet housing drain cock assembly within the range shown in the illustration.
Install the water inlet housing drain cock assembly within 3 minutes.
Do not add coolant for 1 hour after installation.
Be sure to only tighten the water inlet housing drain cock assembly up to 360 degrees to position the pipe. Do not loosen the water inlet housing drain cock assembly to position the pipe.
Make sure to position the pipe within the range shown in the illustration.
11445
18.INSTALL CYLINDER BLOCK WATER JACKET SPACER (for TMC Made Engine)
Install the water jacket spacer as shown in the illustration.
11445
19.INSTALL CYLINDER BLOCK WATER JACKET SPACER (except TMC Made Engine)
Install the water jacket spacer as shown in the illustration.
11115
20.INSTALL CYLINDER HEAD GASKET
11101
21.INSTALL CYLINDER HEAD SUB-ASSEMBLY
13050
22.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY
13523
23.INSTALL NO. 2 CAMSHAFT TIMING SPROCKET
11821
24.INSTALL NO. 2 CAMSHAFT BEARING
11811
25.INSTALL NO. 1 CAMSHAFT BEARING
13511
26.INSTALL CAMSHAFT
13519
27.INSTALL OIL PUMP DRIVE GEAR
15100
28.INSTALL OIL PUMP ASSEMBLY
13507
29.INSTALL NO. 2 CHAIN SUB-ASSEMBLY
13521
30.INSTALL CRANKSHAFT TIMING SPROCKET
13561
31.INSTALL NO. 1 CHAIN VIBRATION DAMPER
13506
32.INSTALL CHAIN SUB-ASSEMBLY
13559
33.INSTALL CHAIN TENSIONER SLIPPER
13566B
34.INSTALL TIMING CHAIN GUIDE
19315
35.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE
11301C
36.REPLACE TIMING CHAIN COVER OIL SEAL
11302
37.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
16620
38.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY
13540
39.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY
12101
40.INSTALL OIL PAN SUB-ASSEMBLY
12101A
41.INSTALL OIL PAN DRAIN PLUG
Place a new gasket on the oil pan drain plug, then install it onto the oil pan.
13471
42.INSTALL CRANKSHAFT PULLEY
15600A
43.INSTALL OIL FILTER UNION (except TMC Made Engine with Engine Oil Cooler)
Using a 12 mm hexagon wrench, install the oil filter union.
44.INSTALL ENGINE OIL COOLER (for TMC Made Engine with Engine Oil Cooler)
Clean the oil cooler contact surface on the engine.
Install a new O-ring to the oil cooler.
Apply a light coat of engine oil on the threads and under the head of the oil cooler union.
Install the oil cooler with the plate washer, oil cooler union and nut.
for oil cooler union
for nut
15601
45.INSTALL OIL FILTER SUB-ASSEMBLY
11101J
46.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
Apply a light coat of engine oil to a new O-ring, then install it onto the camshaft timing oil control valve assembly.
Install the camshaft timing oil control valve assembly with the bolt.
16100
47.INSTALL WATER PUMP ASSEMBLY (for TMC Made Engine)
16100
48.INSTALL WATER PUMP ASSEMBLY (except TMC Made Engine)
16173
49.INSTALL WATER PUMP PULLEY
11301K
50.INSTALL CRANKSHAFT POSITION SENSOR (for TMC Made Engine)
11301K
51.INSTALL CRANKSHAFT POSITION SENSOR (except TMC Made Engine)
52.SET NO. 1 CYLINDER TO TDC/COMPRESSION
53.INSPECT AND ADJUST VALVE CLEARANCE
11213
54.INSTALL CYLINDER HEAD COVER GASKET
Install the gasket onto the cylinder head cover sub-assembly.
11201
55.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY
12204
56.INSTALL VENTILATION VALVE SUB-ASSEMBLY
Apply adhesive to the threads of the ventilation valve sub-assembly.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Using a 22 mm deep socket wrench, install the ventilation valve sub-assembly.
12108
57.INSTALL OIL FILLER CAP SUB-ASSEMBLY
Install the gasket to the cap.
Install the oil filler cap sub-assembly.
19100P
58.INSTALL SPARK PLUG
19500
59.INSTALL IGNITION COIL ASSEMBLY
11102A
60.INSTALL CAMSHAFT POSITION SENSOR
89422
61.INSTALL ENGINE COOLANT TEMPERATURE SENSOR
83530
62.INSTALL OIL PRESSURE SWITCH
63.INSTALL RADIO SETTING CONDENSER
89615
64.INSTALL KNOCK SENSOR
65.INSTALL UNION BOLT (for TMC Made Engine with Engine Oil Cooler)
Apply adhesive to the threads of the union bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the union bolt.
15777B
66.INSTALL OIL COOLER PIPE (for TMC Made Engine with Engine Oil Cooler)
Install a new gasket and the oil cooler pipe with the bolt and 2 nuts.
15777
67.CONNECT NO. 3 WATER BY-PASS HOSE (for TMC Made Engine with Engine Oil Cooler)
Connect the No. 3 water by-pass hose to the oil cooler.
15777C
68.CONNECT NO. 4 WATER BY-PASS HOSE (for TMC Made Engine with Engine Oil Cooler)
Connect the No. 4 water by-pass hose to the oil cooler.
16279G
69.INSTALL NO. 3 WATER BY-PASS PIPE (except TMC Made Engine with Engine Oil Cooler)
Install a new gasket and the No. 3 water by-pass pipe with the bolt and 2 nuts.
16268
70.INSTALL NO. 1 WATER BY-PASS PIPE (for TMC Made Engine)
Install a new gasket and the No. 1 water by-pass pipe with the bolt and 2 nuts.
16268
71.INSTALL NO. 1 WATER BY-PASS PIPE (except TMC Made Engine)
Install a new gasket and the No. 1 water by-pass pipe with the bolt and 2 nuts.
| *A | for Automatic Transaxle
for CVT (w/o Air Cooled Transmission Oil Cooler) |
| *B | for CVT (w/ Air Cooled Transmission Oil Cooler) |
16279G
72.INSTALL NO. 4 WATER BY-PASS PIPE (for TMC Made Engine with Engine Oil Cooler)
for CVT:
Install the No. 4 water by-pass pipe with the bolt and nut.
16331A
73.INSTALL THERMOSTAT
16321
74.INSTALL WATER INLET
25051
75.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
17167
76.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
17139
77.INSTALL NO. 2 MANIFOLD STAY
17118
78.INSTALL MANIFOLD STAY
11452
79.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE (for TMC Made Engine)
11452
80.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE (except TMC Made Engine)
15301
81.INSTALL ENGINE OIL LEVEL DIPSTICK
16631A
82.INSTALL IDLER PULLEY BRACKET