Home › Drivetrain › U241E (AUTOMATIC TRANSMISSION / TRANSAXLE) › TRANSMISSION CONTROL CABLE › 2013.04–2014.09
RM24M0E _52 Drivetrain _059578 U241E AUTOMATIC TRANSMISSION / TRANSAXLE _0292102 TRANSMISSION CONTROL CABLE A

U241E AUTOMATIC TRANSMISSION / TRANSAXLE  TRANSMISSION CONTROL CABLE  REPLACEMENT  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.


Hide 17705 2.REMOVE AIR CLEANER CAP

a.

Hide 28800 4.REMOVE BATTERY

a.

Loosen the nut, and remove the bolt and battery clamp.


b.

Remove the battery.


c.

Remove the battery tray.


d.

Detach the 2 wire harness clamps.


e.

Remove the No. 2 air cleaner inlet's bolt.


f.

Remove the 4 bolts and battery carrier.


g.

Remove the 2 bolts and battery bracket reinforcement.


Hide 58534E 5.REMOVE FLOOR CARPET COVER CENTER LH

Hide 33820B 6.REMOVE TRANSAXLE CONTROL CABLE ASSEMBLY

C140274

a.

Remove the nut and disconnect the control cable from the control shaft lever.


b.
C132999

Remove the clip and disconnect the control cable from the control cable bracket.


c.
C133000

Disconnect the control cable from the control cable support.


d.
C138652

Remove the 2 nuts and disconnect the clamp of the control cable.


e.
C133003

Disconnect the control cable from the shift lever.


f.
C133004

Using a screwdriver, pull out the stopper of the transmission control cable.

NOTICE:

Do not remove the stopper. If the stopper is removed, reinstall it to its original position.



g.

Rotate the nut counterclockwise approximately 180° and, while holding the nut in that position, disconnect the transmission control cable from the shift lever retainer.

NOTICE:

Do not over rotate the nut as it will come off the interior spring and the transmission control cable will not be reusable.



h.
C133002

Remove the 2 bolts and control cable.


Hide 33820B 7.INSTALL TRANSAXLE CONTROL CABLE ASSEMBLY

C133005E06
2.25,1.802 2.375,2.042 false 1.438,0.99 1.135,0.875 false 2.375,0.875 2.719,1.073 0.344,0.198 10 false Turn 2.344,2.052 2.646,2.281 0.302,0.229 10 false Nut 0.635,0.76 1.167,0.948 0.531,0.188 10 false Stopper 1.875,0.146 2.281,0.385 0.406,0.24 10 false Push

a.

Rotate the transmission control cable nut counterclockwise approximately 180° and, while holding the nut in that position, press in the stopper until it makes 2 "click" sounds.


b.
U189032E02
1.76,0.646 2.198,0.646 false 2.271,0.552 2.438,0.75 0.167,0.198 10 false A

Install the cable outer of the transmission control cable to the shift lever retainer, check that the position of the spring is the same as A shown in the illustration, and press in the stopper.

HINT:

If the stopper cannot be pressed in, slightly rotate the nut clockwise and then press in the stopper.



c.
C133008

Connect the control cable to the shift lever.

NOTICE:

Make sure the cable is installed to the base of the pin.



d.
C133002

Install the control cable with the 2 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


e.
C132999

Fix the control cable onto the control cable bracket with the clip.


f.
C140274

Connect the control cable onto the control shaft lever with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


g.
C138652

Connect the clamp of the control cable with the 2 nuts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


h.
C133000

Connect the control cable to the cable support.


Hide 17705 9.INSTALL AIR CLEANER CAP

Hide 10.INSTALL BATTERY

a.

Install the battery bracket reinforcement with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.

Install the battery carrier with the 4 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


c.

Insert the No. 2 air cleaner inlet to the bracket with the bolt.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Attach the 2 wire harness clamps.


e.

Install the battery tray.


f.

Install the battery with the battery clamp.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)

for nut



Hide 11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 12.INSPECT SHIFT LEVER POSITION

a.

When shifting the lever from P to the R position with the ignition switch on (IG) and the brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into position.


b.

Start the engine and make sure that the vehicle moves forward when moving the lever from N to the D position and moves rearward when moving the lever to the R position.

If the operation cannot be performed as specified, inspect the park/neutral position switch and check the shift lever installation condition.


Hide 58534E 14.INSTALL FLOOR CARPET COVER CENTER LH

Hide 15.PERFORM INITIALIZATION

a.

Perform initialization (see page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).

NOTICE:

Certain systems need to be initialized after disconnecting and reconnecting the cable from the negative (-) battery terminal.