If any of the following conditions are detected, the brake warning light remains on:
The ECU connectors are disconnected from the skid control ECU.
The brake fluid level is insufficient.
The parking brake is applied.
The EBD is defective.
Check that both of the following conditions are satisfied.
The brake fluid level in the brake master cylinder reservoir is correct.
The parking brake is released.
When the ABS warning light remains illuminated, repair the malfunctions in the ABS system first.
NEXT
Check if any ABS DTCs are output (see page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Check if the CAN communication system DTC is output (see page Power Source / Network>CAN COMMUNICATION>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC is output | B |
A
B
Check if the skid control ECU connector is properly installed.
The skid control ECU connector is properly installed.
OK
NG
Disconnect the A9 ECU connector.
Measure the resistance of the wire harness side connector.
| Tester Connection | Specified Condition |
|---|---|
| A9-4 (GND1) - Body ground | Below 1 Ω |
| A9-1 (GND2) - Body ground | Below 1 Ω |
Measure the voltage of the wire harness side connector.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A9-28 (IG1) - Body ground | Engine switch on (IG) | 10 to 14 V |
OK
NG
Using the Data List, check for proper functioning of the parking brake switch.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Parking Brake SW | Parking brake switch / ON or OFF | ON: Parking brake applied
OFF: Parking brake released |
- |
When the parking brake lever is operated, the display changes as shown above.
OK
NG
Remove the reservoir tank cap and strainer.
Disconnect the A10 brake fluid level warning switch connector.
Measure the resistance of the switch.
A float is placed inside the reservoir. Its position can be changed by increasing or decreasing the brake fluid level.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (+) - 2 (E) | Switch OFF (Float up) | 10 kΩ or higher |
| 1 (+) - 2 (E) | Switch ON (Float down) | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
If there is no problem after the above check is finished, adjust the brake fluid level to the MAX level.
A
B
C
Disconnect the G28 combination meter connector.
Disconnect the A10 switch connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| G28-26 (#10) - A10-1 (+) | Below 1 Ω |
| G28-26 (#10) - Body ground | 10 kΩ or higher |
| A10-2 (E) - Body ground | Below 1 Ω |
OK
NG
Check the combination meter (see page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
| Result | Proceed to |
|---|---|
| OK (for 2AZ-FE) | A |
| OK (for 2GR-FE) | B |
| NG | C |
A
B
C
Remove the parking brake switch.
Measure the resistance of the switch.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - Body ground | Parking brake switch ON
(Switch pin not pushed) |
Below 1 Ω |
| 1 - Body ground | Parking brake switch OFF
(Switch pin pushed) |
10 kΩ or higher |
OK
NG
Disconnect the 4D ECU connector.
Disconnect the A4 switch connector.
Measure the resistance of the wire harness side connectors.
| Tester Connection | Specified Condition |
|---|---|
| 4D-13 (PKB) - A4-1 | Below 1 Ω |
| 4D-13 (PKB) - Body ground | 10 kΩ or higher |
OK
NG